Models > MDE7600AYW > Instructions

MDE7600AYW Maytag Dryer - Instructions

All installation instructions for MDE7600AYW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDE7600AYW
61-75 of 641
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Switch did not turn off dryer when door opened

  • Customer: paul from madison CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
Switch can be removed from outside of dryer and your video described the repair as having to work from inside dryer. But since wires were still attached to old switch, it could be popped out and wires switched. Since there were three wires on new switch to allow it to turn on and off a circuit, it was useful to check the resistance of the switch compressed or released to be certain I was attaching the two wires to the right two poles of the new switch. But that all required only a couple of minutes. Thank you.

Drying time was taking longer than it should.

  • Customer: Vicki from Springfield MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
I simply went on line and ordered the part. I had it shipped to my office since I am here all day, M-F. I received the part in 2 days. I took it home, pulled out the old lint filter and slid in the new one. It is amazing how much more efficient my dryer is. The old lint filter had about a 6 inch tear in it so it was not catching all the lint.

All three baffles fell out of dryer drum; one by one in a week time span; of course the warranty expired in May of 2007. Figures!

  • Customer: Sandra from Germantown TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 7 people found this instruction helpful
Had to remove the dryer door and back top screws to access the drum.
Once this was accomplished all that had to be done was to turn the drum by hand and replace each baffle and (two) screws each.

Noisy and thumping drum

  • Customer: Barry from League City TX
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
I set the dryer on its back to make alignment of the front drum guide cover easy to reinstall in the seal after completion. I removed the 2 screws at the bottom front then removed the white and yellow wires to the interlock switch and set the front cover aside. I then removed the 4 nut screws holding the front drum cover and removed. On the back side there are two teflon and cork "bearings". I had ordered two even though only one was worn down to metal. On each one I then removed the two rivets by drilling them out. Then I placed the corks into the bearing slots with a little glue then inserted the teflon into the slots and riveted them into place with the rivets that came with the kit. I replaced the drum cover, connected the switch and screwed the dryer front cover back on. I set the dryer back up. Connected the vent hose and turned the dryer on. Beautiful sweet smooth and quiet operation. I had replaced the front and back drum seals a few months ago and saw the teflon was missing but did not have the kits at that time. With a complete job I would recommend replacing the front and rear drum seals and the two teflon/cork bearing kits at the same time.

Loud noise - missing baffle

  • Customer: Ron from Fresno CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 4 of 4 people found this instruction helpful
1 - unscrewed door
2 - made a mess because the directions did not work for my dryer
3 - figured it out = eventually
4 - popped loose the front panel
5 - unscrewed metal bars (that were holding the top down in the front)
6 - lift front like a hood on a car
7 - unscrew the rest of the front until the drum was loose and I could get to the felt strip
8 - glue new strip on where the old strip was = to the front and back plates that hold the drum
9 - put it back together :)

Loudly squealing dryer

  • Customer: Donald from Bridgewater MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
Piece of cake. Use the available manual to ascertain dismantling procedure. Only thing that might be tough for average DIY'er is the internal snap rings. Snap ring pliers are mandatory for quick easy repair.
Total time was probably about 15 minutes and this was the first time I had taken it apart. Quiet as a mouse now!
Very helpful site.

Dryer timer dial was cracked and thus would not turn the timer pivot.

  • Customer: Richard from Keswick VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 4 of 5 people found this instruction helpful
Ordered the three pieces of the dryer dial and replaced the old dial with the new one.

Timer skirt/knob was broken and dryer wouldn't start

  • Customer: Maurice from Sunriver OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
I removed the knob and timer skirt after viewing the same on the parts diagram provided by PartSelect. This was very helpful. I ordered the new part, received it in just a few days, reinstalled the parts and everything works fine.

The key was the diagram provided so I knew exactly what to order and how the parts could be taken apart and reassembled.

Dry er would run but no heat.

  • Customer: Randall from Viper KY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
Appliance dealer stated that usually timers did not go out and thermostats were most likely . Tried all and called repairman that did not show. Removed cover found burned gear in timer ordered. The part is easy to replace just change wires one at a time or take a digital pic of the wires.

my parents lint filter had holes in it

  • Customer: Scott from Van Nuys CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
I simply put the new lint filter in the spot for it inside the door.

High-pitched squeeking when running

  • Customer: James from Jupiter FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 3 of 3 people found this instruction helpful
UNPLUG THE UNIT First, I removed the 2 screws from bottom of the front panel. I removed the panel and disconnected the switch wires. Next, I removed the 4 bolts from the front tumbler support with a socket. I removed the tumbler, but left the belt inside. I cleaned up the inside as much as possible and removed both support rollers with a 1/2 in. straight wrench. (Save the nuts.) I removed the clips to reuse with the new shafts, attached the new washers and rollers, and resecured the shafts in place. Next reset the tumbler with the belt slacked over the back support. Let the tumbler rest on the blower pipe to allow slack to bring the belt over the tumbler and around the drive and idler wheel. Then, set tumbler back into rear seat and reattach front support and panel. I tested the unit before attaching the front panel. Works great!!

Our timer dial had been broken for some time, cracked around the connection to the control panel. I had been able to epoxy glue it to where it was functional, but that eventually failed. We were using a pair of pliers to set the timer on the dryer.

  • Customer: Joanne from Missouri City TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
I was able to easily find the replacement part on PartSelect, and the schematics showed me how to easily disassemble my dial (which has three parts) so that only the broken part needed to be replaced. I used a tiny straight-slot screwdriver to pop the pieces apart. Once we received the new piece, it was very simple to pop the pieces back together and have a fully functioning new dial!

dryer drum not turning well clothes were wrinkled

  • Customer: Cindy from Vincent OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 9 people found this instruction helpful
Took off the front, took thd drum off, removed old belt, placed on new belt ptu everything back together.

The inner dor had broken and would not hold the seal.

  • Customer: Mark from Boaz AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Took the door off the hinges. Removed remaining 6 screws and clips. removed the inner door. Made sure the door seal was correctly installed in the inner door. Installed the inner door and seal. Put the clips and screws back in. attached door to the hinges and was back in business.

The dryer door latch was broken.

  • Customer: Jack from Memphis TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.
All Instructions for the MDE7600AYW
61-75 of 641