MDE508DAYW Maytag Dryer - Instructions

Un plug the dryer ***
Pulled the top portion of the dryer off
Used socket to undue two nuts to remove the front panel and unhooked the wires.
unscrewed 3 screws and took out the air duct assembly. Cleaned the dryer of all lint and replaced the air duct with a new one.
Reverse the process.

Simply remove the front panel screws(2) at the bottom of the dryer. Pull bottom of panel outward until it swings free of the top(taking care not to pull the wires out). Rotate out of the way and remove the two left side screws holding the drum plate and snake the belt around the flange. Reinstall those screws and remove the same ones on the right side. Snake the belt behind that flange and reinstall screws. Then all you have to do is run the belt around the motor sheave and the idler pully and your done. Reinstall the front panel.

Searched Maytag.com and other sources, only partselect.com had what I needed. Three days after my purchase, our dryer lint screen was again fully functional.

First, I unplugged the dryer. Then I used a flat screw driver to pop the top open. I removed 2 bolts from the front cover and removed the front door cover. I also took pictures of the electrical connector on the door so I would remember how the wires went back on. Then I removed 4 bolts from the front drum guide and lint screen holder. This allowed me to remove the drum & old belt. While the drum was out, I pried an access panel open on the side of the dryer. I then glued the new back felt piece in place. I put the new belt around the drum and re installed it. I re-installed the front guide and front cover re-connecting the door electrical switch. With the access panel open, I attached the belt to the motor. I then plugged it back in and turned it on to verify operation pryor to snapping the top cover back in place. Very easy repair.

removed the dryer female part that was broken with needle nose pliers and inserted the new one, on the door i removed one phillips screw and r/r the male piece with the new one and re-inserted the screw. that was all, very easy repair

Because the wheel had stopped and the shaft kept turning (junk from child's pocket got in there), the nut stripped itself away from the wheel causing low RPM and low air movement (lazy flame, vibration and clothes not drying)

I had to use a screwdriver to break the wheel away from the center nut and remove the fan. I then removed the air fan housing (3 bolt behind the fan wheel). I used a small pair of vise grips to hold the motor shaft staionary while I used a pair of channel lock pliers to remove the nut that was molded into the fan from the motor shaft. It was harder to get the nut started then I would have thought.

Once complete, I put the fan housing back on and threaded the new wheel on easily. The motor has external fins on it which turn with the shaft-I held one lightly while I threaded the fan on to keep the shaft from turning. Tighten just slightly more than hand tight-don't go crazy-it's threaded to stay tight with rotation. Works great and very quiet now.

Took off back cover, thermostat was easily identified because of photos I've seen on website. Took 2 connectors off, removed 2 screws and removed old thermostat. That was pretty much it!

NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.

Squeling from inside dryer. To Fix-
Pry dryer top cover off by popping cover off the two fastening clips located at about 3" inward from the two front corners. A screw driver at these two locations is easily inserted between the top cover and front panel.
Next remove the two screws on the top inside of the driver approximate size 5/16 inch. Pull the top of the front panel outward and then note how the lower portion clips into the fram, lift the front panel off the clips and roll it to the right. Remove the 4 screws and bulkhead.
Draw a picture of how the belt wraps around the drum and idler. Also note the belt orienation on the drum. Roll the belt off the idler pully and reomve the drum.
Replaced Idler asembly by first removing the tension spring and lastly the retaining bolt.
Reinstall everything in reverse order. Can be a bit tough getting the belt around the idler and motor pulley however this is managable. My machine runs great now!
Once again Parts Select comes through with great delivery, perfect fit, good pricing, accurate parts list. This is my third purchase and I have been 100% pleased. By far the best on line service I have ever experienced.

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

I opened the front panel and removed the heating element from the rear of the dryer by removing the two screws that held it in place, and slid the element out. using a mulitester I checked the High limit Fuse and it was not working.I ordered the part and replaced it. Everything worked great for two days and the dryer stopped heating again. My brother asked if I had replaced the thermostat because something burned out the fuse. He was right. I ordered both parts and replaced them. Every thing is working just fine. Save some money and time by replacing both parts at the same time.

I removed the dryer front and the drum, then disconnected the wires from the dryer motor and removed it from the motor mount, after installing the new motor in the motor mount the rest was just putting the dryer back together the same way I took it apart, the best way to do this is to print out the diagram from partsselect.com and follow it step by step, this was so easy everybody can do this and save alot of money for the labor and the parts mark-up, try it you all can do it (SO EASY)

I first thought the drum rollers were the source and replaced those. It took me 60 minutes to get the dryer disassembled and wires labeled for reassembly the first time. Knowing how to do it for this repair made everything go quicker.
I removed the tension from the belt by pulling it away from the spring and then slipped the belt off the motor. I then removed the drum from the dryer to get to the idler arm assy.
The trickest part of this repair was putting a box wrench on the nut on the motor side of the frame. I found a 3/8" box wrench with an angled handle that worked well. I then used a 7/16" socket on the other side of the idler arm base and removed the bolt. I was careful to note the position of the tension spring so that I could put it back together correctly. I then put the new idler arm assy in place with the bolt through the frame but had some trouble keeping the nut in the box wrench. I ended up using a bit of chewing gum to keep the nut in the box wrench long enough to get it threaded!

From there it was a cinch - just put the belt back around the drum, the idler wheel and then pulled up on the arm while I slipped the belt over the motor. No more screeching!

Switch can be removed from outside of dryer and your video described the repair as having to work from inside dryer. But since wires were still attached to old switch, it could be popped out and wires switched. Since there were three wires on new switch to allow it to turn on and off a circuit, it was useful to check the resistance of the switch compressed or released to be certain I was attaching the two wires to the right two poles of the new switch. But that all required only a couple of minutes. Thank you.

Remove front pannel
remove wires to light and switch
remove drum panel
disconnect motor wiring
unscrew motor mount
replace idlerlever replace belt reassemble all parts

1. Disconnect power and hose. Use a putty knife to release top of dryer. Two restraints couple inches in from each side on front. Raise top and do not remove. Block it up in vertical so it doesn't fly down to back.
2. Disconnect five wires at front. Use magic marker to mark re-installation instructions on underside of top.
2. Remove metal screws (2) that hold front to frame. Remove front.
3. Pull dryer forward and put cardboard box, or some such thing under back to support when laying dryer down.
4. Remove frame (4 screws) that supports filter assy and front of drum.
5. Remove belt. Mark assy. sequence on underside of top.
6. Remove drum.
7. Stand dryer back to upright position.
8. Disconnect spring from idler lever. Drop light may help here. Note position of lever for re-install of new.
9. Unscrew bolt that holds idler lever. Nut is on back of bracket. Must re-install this way as bolt has pivot surface for lever on front side.
10. Install new lever and reconnect spring.
11. Lay dryer back on box.
12. Put drum back in place. Insure it seats well all around the felt gasket. Any misalignment here and it will not rotate smoothly.
13. Put belt around drum using small pieces of tape to hold it into position around drum, and them depress the idler lever and install belt around motor pulley. Rotate drum to insure it rotates smoothly. Remove tape.
14. Re-install filter bracket and insure drum seats nicely in felt gasket. Again, rotate to insure smooth operation.
15. Pull dryer back to standing position and reinstall the front, and re-connect the wires.
16. Lower top and push down to reconnect locking devices.
17. Plug in dryer and turn on to see if all is well.
18. Re-install hose and start drying all those clothes.