This drum support roller is used for square-ported model clothes dryers. This part is sold individually; however, rollers tend to wear at the same rate, so it is suggested that both should be replaced...
$20.95
In Stock
Order within the next 11 hrs and your part ships today!
This dryer drum drive belt attaches to the motor pully and works the drum as the motor rotates. The belt has a length of 93- 3/6 inches, and wraps all the way around the dryer drum, around a tension p...
$9.44
In Stock
Order within the next 11 hrs and your part ships today!
If your dryer is noisy, will not tumble, or is leaving marks on your clothes, you may need to replace the drum glide. The drum glide is installed on the front bulkhead either at the top or the bottom,...
$14.17
In Stock
Order within the next 11 hrs and your part ships today!
This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found...
$7.95
In Stock
Order within the next 11 hrs and your part ships today!
Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do...
$12.97
In Stock
Order within the next 11 hrs and your part ships today!
This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appli...
$32.34
In Stock
Order within the next 11 hrs and your part ships today!
The spring for this part is sold separately.
This idler assembly is for dryers.
Idler assembly includes the idler arm and the idler pulley that maintains tension on the drive belt, allowing the ...
$35.69
In Stock
Order within the next 11 hrs and your part ships today!
The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place o...
$13.58
In Stock
Order within the next 11 hrs and your part ships today!
This cylinder felt seal is used in dryers and is located between the back of the drum and the rear dryer panel. If your dryer is experiencing any of these symptoms, replacing the felt seal could solve...
$48.55
In Stock
Order within the next 11 hrs and your part ships today!
This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start, or does not tumble,...
$29.94
In Stock
Order within the next 11 hrs and your part ships today!
This dryer drum glide pad is an inch long. It is made of a felt material and is used for gas and electric clothes dryers. The dryer drum glide provides a soft surface for the front of the drum glide a...
$8.00
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for MDE308DAYW
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Hudson
January 2, 2020
I found your website to be very helpful. My wife uses the dryer regularly but recently it stopped drying in the "auto dry wrinkle control" setting that she regularly uses. It no longer heats on the "auto dry wrinkle control settings" (i tried the "extended tumble switch"in both modes) however the timer did advance. The dryer will heat in in the "auto dry regular" and the "time dry air fluff" settings. I removed and tested the high limit thermal fuse, limit thermostat, and the cycling thermostat as recommended on the website. All check out and seem to be functioning properly. I installed a new dryer vent and cleaned all dust and debris from inside the dryer however the dryer still will not heat in the "auto dry wrinkle control" mode. Do you recommend replacing the timer? Any other recommendations. I can have her use the other setting but am wondering since the one setting quit working properly will the other setting follow suit. Thank you for any recommendations.
For model number MDE308DAYW
Hi Hudson, thank you for your question. Yes, it does seem like that would be the part to check next. If you are only getting an error with one specific cycle, then it is likely the timer there. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Lee
February 2, 2020
Need to know how to plug the wires back in the timer which wire goes where
For model number MDE308DAYW
Hello Lee,
Thank you for your question. We suggest viewing the wiring diagram on your models diagram list, or take a picture of how the original timer was wired before installing the new timer to plug in the wires as it was on the original. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Rick
September 13, 2021
Can you tell what year my dryer was manufactured based on its serial number, which is: 11058062jr, type 111. Thanks
For model number MDE308DAYW
Hello Rick, Thank you for the question. According to the serial number this product may have been manufactured September of 2006. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Steve
December 20, 2019
Not sure how to remove panels to check for worn belt or wheels.
For model number MDE308DAYW
Good Day Steve. Thank you for your question in regards to your unit. The following URL will take you to a YouTube Video that should be able to assist you with what you are looking to do: https://www.youtube.com/watch?time_continue=3&v=KYafjwm8ijk&feature=emb_logo. Hope this helps. Best Regards.
1 person found this helpful.
Was this helpful?
Thank you for voting!
MARK
July 22, 2021
Is the heating element for this model in the back or front
For model number MDE308DAYW
Hi Mark,
Thank you for your question. The element would be located in the heater duct assembly located in the back of the dryer. We hope this helps. Thank you and have a great day!
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared of
... Read moref. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it.
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surface
... Read mores and let dry. I then applied a 2nd coat and let get "tacky" and installed the gasket. You will need an extra set of hands to hold the gasket in place while you stretch it over the the panel. The vent manifold is held in place with 3 phillips screws and was installed in about 10 minutes. The only gripe I had was in the Parts-Select illustrated breakdown they don't tell you the lint screen comes with the manifold assembly, so I bought one of them too. Now have an extra lint screen
Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to. Followed other people's excellent instru
... Read morections. Clean out all the dust bunnies. Schematics were a great resource. Those and the prices made me a repeat customer. The shaft of the Idler Lever wheel was the cause, but decided, since I had it apart, to spend a little more money and replace both Drum Support Rollers and the Roller Bracket and Shaft Assembly. They showed some wear, and the parts were very inexpensive. Make sure you have snap ring pliers with prongs that are smaller than the standard 0.40 to save some aggravation with the Drum Rollers. $5 tool. Total parts were less than $60. Probably saved $150+ in labor. Quieter than ever now. Thanks!