Models > MDE3000AYW > Instructions

MDE3000AYW Maytag Dryer - Instructions

All installation instructions for MDE3000AYW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDE3000AYW
526-540 of 619
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken short baffle

  • Customer: Teresa from Acworth GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
My husband, who normally calls a repairman for everything, followed the video and replaced the short baffle in less than 30 minutes from start to finish(this includes 2 or three trips up and down stairs to retrieve the right tools even though the video tells you the right tools to use). The part was identical to the original one and arrived in less than a week. Am very pleased with the whole process and am so thankful for the step by step video. The full repair was less than $30.00 for the part and my husbands time. I had been given a quote over the phone for this same repair of $250.00 to $375.00. Thank you so much and I will definitely buy from here again if it becomes necessary.

Horrible squeal when dryer was on

  • Customer: Genie from Dayton WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Checked YouTube and saw a video that described the removal of the drum, belt and rollers - step by step. Ordered the parts. Once they arrived, we realized we didn't need all that we purchased, but putting the dryer back together was easy and the dryer no longer squeals when on. YEAH FOR US!

rollers worn ,rumbling when drum turned

  • Customer: scott from auburn MA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
removed front cover and rear access panel took belt off tensioner removed front drum support removed drum replaced two rollers by removing snap rings and put it back together in reverse... The maytag repair man is still lonely

Loud squeak coming from rollers

  • Customer: David from Chino CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The online video was the extremely helpful in aiding me in the repair. Thank you so much for posting it. Couldn't have done it without it.

The timer skirt broke

  • Customer: Everett from Clute TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered new timer skirt. Watched video on replacing it. Removed timer dial skirt and knob. Used screwdriver to release tabs on knob. Made sure the metal insert on old skirt came off with the old skirt. Installed new timer dial skirt, pressed knob into place and made sure it latched. Installation complete in 30 seconds. Fit and works perfectly. Only problem I have had in 14 years other than the inside light burns out often. Thank you!

noisy and drum wobbling

  • Customer: Jeffery from West Linn OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Installing the Front Glide Kits was straight forward if you watch the video. The guides resolved a part of my problem, but I discovered the Blower Wheel was cracked and out of round. replaced it and poof its fixed!

broken door catch: female half

  • Customer: Allen from Seattle WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
noticed that male half was in good working order, so I just snapped in the new female half; without any tools. easy repair!

loud noise

  • Customer: Rachel from Tabernacle NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
watched the video, took the dryer apart, installed the new parts, reassembled the dryer, video was very helpful .

New rollers replaced

  • Customer: David from Helena MT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the guidance on video.

dryer started making nocking noise

  • Customer: Myra from Dillon SC
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
found info describing the nocking noise found parts to fix it watched video on how to do the repair The step by step instructions made the job so easy We saved over 150.00 in doing the job ourselves. thank you I am amazed at how simple this turned ou to be.

Belt was squeaking

  • Customer: Kent from Sealy TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Sorry didnt unplug it. Just took door off. undid next panel and moved it to the side. Took bottom front panel couple of hex screws. Lifted basket out a little took belt off and replaced with new belt reversed order of panels and started it up.

slow in drying, making a lot of noise

  • Customer: Byron from West Harrison IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions

knob for timer select was broken, the plastic around the metal part was cracked

  • Customer: Robert from Huntley IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
very easy remove the old part, insert new one, works great

timer knob was cracked allowing it to spin around the timer setting stem

  • Customer: David from Lenoir NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the old knob and skirt. Replaced them with the new parts. Works like new!

Problem with dryer.

  • Customer: CYNTHIA from East Haven CT
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Someone thought it was rollers. It was not. Maybe motor. Will check out further. Thanks for good service, Cynthia
All Instructions for the MDE3000AYW
526-540 of 619