Models
>
MDE216RBW0
MDE216RBW0 Tappan Dryer - Overview
Sections of the MDE216RBW0
[Viewing 3 of 3]Keep searches simple, eg. "belt" or "pump".
Rear Drum Bearing Kit
PartSelect #: PS459829
Manufacturer #: 5303281153
This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will not tumble, or if i...
$62.48
In Stock
Drum Belt
PartSelect #: PS1148434
Manufacturer #: 134503600
This drum belt, often referred to as a drive belt, is used in the assembly of dryers. It goes around the drum, the idler pulley, and the motor pulley. As the armature on the motor spins, this belt is ...
$17.66
In Stock
Drum Support Bearing
PartSelect #: PS418807
Manufacturer #: 131825900
If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which a...
$6.33
In Stock
Thermal Limiter - Limit 220
PartSelect #: PS419402
Manufacturer #: 134120900
The dryer thermal limiter, also known as a thermal fuse, blows the fuse to cut off power to the dryer when the dryer begins to overheat. Once the dryer reached 220 degrees Fahrenheit, the heat cuts ou...
$27.24
In Stock
Dryer Drum Bearing Bracket
PartSelect #: PS12579101
Manufacturer #: 131724301
This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing
$10.64
In Stock
Idler Pulley Assembly
PartSelect #: PS457526
Manufacturer #: 5303212849
Use this idler pulley assembly with gas or electric clothes dryer that has a flat dryer belt.
***Please NOTE: This part has been redesigned by the manufacturer and may not fit your appliance.
No Longer Available
Heater Coil with 5/16 Inch Terminals
PartSelect #: PS451032
Manufacturer #: 5300622034
Coil only.
$80.45
In Stock
Heater Assembly
PartSelect #: PS2378363
Manufacturer #: 131475320
This dryer heating assembly has 5/16" terminal on the housing.
$175.15
In Stock
Levelling Leg
PartSelect #: PS418072
Manufacturer #: 131527400
Sold individually.
No Longer Available
Cycling Thermostat - 4 Terminal
PartSelect #: PS417453
Manufacturer #: 131298300
This operating or cycling thermostat is used in dryers to monitor and direct the temperature inside the dryer. If your thermostat is shorted out and it will not allow the heat to come on, it is best t...
$33.91
In Stock
Questions And Answers for MDE216RBW0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the MDE216RBW0
[Viewing 4 of 4]Noisy
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loud Squeaking
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum be ... Read more lt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum be ... Read more lt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.
Read less
Parts Used:
-
Frank from Boyertown, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
333 of 349 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thermal Limiter opened
Unplugged Dryer.
Opened top of Dryer, over the drum.
Removed Thermal Limiter.
Tested the Thermal Limiter - found it was open.
Checked all vents and exhaust tube for lint build-up.
Replaced Thermal Limiter.
Closed top of dryer.
Plugged Dryer back.
Tested Dryer - it works.
Opened top of Dryer, over the drum.
Removed Thermal Limiter.
Tested the Thermal Limiter - found it was open.
Checked all vents and exhaust tube for lint build-up.
Replaced Thermal Limiter.
Closed top of dryer.
Plugged Dryer back.
Tested Dryer - it works.
Parts Used:
-
Stephen from Newnan, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
242 of 318 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat
First..kudos to PartSelect for their fantastic support! Great work folks.
While greasing the bearing in the back of the drum, I found my heating coil was broken. Steps to replace:
1) Unplug the unit
2) Remove the top panel. Note, do not remove the center front screw that does not go into the door.
3) Rem ... Read more ove front outer panel
4) Remove interior front panel
5) Remove front control panel 6 screws, pushing downward the panel and disconnecting connection to door.
6) Remove door by removing the screws on the top and pull door straight off. (I left the air duct attached to the door)
7) Remove the back access panel to the motor
8) Release the belt from the idler pulley and remove the belt.
9) I removed the three screws in the center of the drum as I found it difficult to remove the drum from the bearing. Remove the drum.
10) disconnect the coil terminals by first bending the tabs outward to allow you to be able to pull them off the block
11) remove the old coil
12) carefully stretch the new coil so that it measures 48 inches (no more)
13) Plug new coil into terminals and bend tabs to lock in place.
14) Divide heater coil in half and install coil onto center support on the opposite side from where it connects to the block/back wall of dryer
15) Install remaining coils onto supports.
16) reinstall all parts in reverse order.
While greasing the bearing in the back of the drum, I found my heating coil was broken. Steps to replace:
1) Unplug the unit
2) Remove the top panel. Note, do not remove the center front screw that does not go into the door.
3) Rem ... Read more ove front outer panel
4) Remove interior front panel
5) Remove front control panel 6 screws, pushing downward the panel and disconnecting connection to door.
6) Remove door by removing the screws on the top and pull door straight off. (I left the air duct attached to the door)
7) Remove the back access panel to the motor
8) Release the belt from the idler pulley and remove the belt.
9) I removed the three screws in the center of the drum as I found it difficult to remove the drum from the bearing. Remove the drum.
10) disconnect the coil terminals by first bending the tabs outward to allow you to be able to pull them off the block
11) remove the old coil
12) carefully stretch the new coil so that it measures 48 inches (no more)
13) Plug new coil into terminals and bend tabs to lock in place.
14) Divide heater coil in half and install coil onto center support on the opposite side from where it connects to the block/back wall of dryer
15) Install remaining coils onto supports.
16) reinstall all parts in reverse order.
Read less
Parts Used:
-
Mark from Normalville, PA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
107 of 126 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!