Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDE208DAYW

MDE208DAYW Maytag Dryer - Overview

Get Parts and Repair Help for MDE208DAYW

If you know the dryer repair part you need, you can browse the list of all parts on the MDE208DAYW, or you can search by name or part description. You can also find your part by where it is located on the MDE208DAYW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for MDE208DAYW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$20.00

Multi Rib Belt - 93-3/8"

At 93-3/8" inches in length, this dryer drum belt from Amana has five ridges. It is all black in color and is made entirely of rubber. A flat belt, it is 3/8 of an inch wide.

Order within the next 4 hrs and your part ships today!
$12.69

Drum Support Roller - for square ported models

This single drum support roller is used for square ported model clothes dryers. It has a metallic bearing in its center.

Order within the next 4 hrs and your part ships today!
$7.86

Drum Glide

This drum glide is sold individually. ***Please Note: these should be replaced in pairs.

Order within the next 4 hrs and your part ships today!
$34.42

Lint Filter

Note: This part no longer comes with the felt seal. This filter collects lint as it passes through the dryer vent.

Order within the next 4 hrs and your part ships today!
$7.22

High Limit Thermal Fuse

Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when ...

Order within the next 4 hrs and your part ships today!
$17.81

Idler Lever

The spring for this part is sold separately.

Order within the next 4 hrs and your part ships today!
$5.15

Washer, Thrust

This washer is 3/4 inches in diameter.

Order within the next 4 hrs and your part ships today!
$19.30

Cylinder Felt Seal

This part is located between the back of the drum and the rear dryer panel.

Order within the next 4 hrs and your part ships today!
$16.03

Door Catch Kit

This kit comes in two pieces: the catch and the clip.

Order within the next 4 hrs and your part ships today!
$46.77

Heating Element (Orange Dot)

This orange dot heating element replaces those elements with an orange dot on the element flange. It carries 240 volts.

Order within the next 4 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drum not centered , clothes getting stuck in dryer

  • Customer: Chris from Hopedale, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 488 of 494 people found this instruction helpful
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new d... read more

The Felt Gasket between drum and door ripped, vent manifold from Dryer to fan and lint screen broken

  • Customer: Tim from South Glens Falls, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 477 of 480 people found this instruction helpful
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surfaces and let dry. I th... read more

Squeeling and grinding noise

  • Customer: Steven from Holderness, NH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 426 of 431 people found this instruction helpful
Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to.
Followed other people's excellent instructions. Clean out al... read more