Models > MDE17MNAZW1

MDE17MNAZW1 Maytag Dryer - Overview

Get Parts and Repair Help for MDE17MNAZW1

If you know the dryer repair part you need, you can browse the list of all parts on the MDE17MNAZW1, or you can search by name or part description. You can also find your part by where it is located on the MDE17MNAZW1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for MDE17MNAZW1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$28.26

Lint Filter

This filter collects lint as it passes through the dryer vent.

$18.41

Door Switch - 3 Wire

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

$13.86

Idler Pulley with Tri-Ring and Gasket

A dryer's idler pulley helps the belt to rotate the drum. Also known as dryer belt tension pulley wheel.

$4.46

Thrust Washer

$10.77

Door Catch Kit

This kit comes in two pieces: the catch and the clip.

$3.66

Leveling Foot

Sold individually.

$40.05

Dryer Repair Kit

This kit comes with one multi rib belt, four drum support rollers, one idler assembly, nine tri rings and one washer.

$31.80

High Limit Thermostat and Thermal Fuse Kit

Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than the thermostat. Once it trips, it has to be replaced.

$4.11

RING

$2.70

Screw

This screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer would not turn off with door open

  • Customer: RICHARD from NORCROSS GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 382 of 384 people found this instruction helpful
pryed dryer top open and opened front door.. unscrewed the 2 retaining screws. pulled old switch from the wiring harness.
put new switch in place and replaced the retaining screws.
put new switch wire plug into the wiring harness. before closing top, checked door switch function with dryer on.
dryer cut off when door open and when close... read more

Dryer wouldn't turn on b/c door switch broken

  • Customer: April from Xenia OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 279 of 349 people found this instruction helpful
It was simple once I figured out what to do:). I removed the 2 screws on the top of the dryer... they were a bit hard to find. Even with the other descriptions on this site. I was removing things I didn't need to. The 2 screws you need to remove are under the LINT COLLECTOR LID. Remove those 2 screws & lift the lid... it will be tight at first. the fro... read more

When I opened my dryer door while it was running, the drum continued to turn and the light would not come on.

  • Customer: Baxter from Goodlettsville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 102 of 163 people found this instruction helpful
First unplug your dryer. Then, I removed the two screws on the lint trap leaving the lint trap in place--do not pull out the lint trap--only remove the two screws. Next, slide the top of the dryer slightly forward in order to release the top of the dryer. I did this with my hands. Once the top of the dryer is released, raise the top of the dryer and unplug ... read more