Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDE16MNDZW > Parts

MDE16MNDZW Maytag Dryer - Parts

All parts for the Maytag Dryer MDE16MNDZW

Below is a list of all parts for the Maytag Dryer MDE16MNDZW - Electric. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the MDE16MNDZW
1-14 of 146
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.85

Drum Support Roller Kit

This drum support roller kit includes one drum roller and two bearings/washers. Most dryers use two drum rollers; it is recommended to change both at once. The drum support roller ...

$4.60

Roller Shaft

This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller; it provides a place for the roller to spin. The tools required for this repair include a stubby Phillips screwdriver, a 5/16 nut driver, a pair of snap ring pliers, and a 9/16 wrench. The first step before making this repair should be to disconnect your dryer from the power source.

$9.89

Front Glide Kit

The front glide is located at the front of the dryer and the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out an...

$14.56

Multi Rib Belt - 91-5/8"

At 91-5/8 inches in length, this dryer drum belt from Maytag has five ridges. It is all black in color and is made entirely of rubber. This flat belt is 3/8 of an inch wide.

$10.10

Idler Pulley Wheel and Bearing

This idler pulley wheel is white and made of plastic. It is two inches in diameter and comes with a center bearing.

$2.94

Retaining Ring

This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter. The retaining ring is a genuine OEM part sourced directly from the manufacturer. The ring may vary in appearance due to manufacturer substitution, but the function is the same. You may need to replace this part if the dryer is noisy during tumbling, will not tumble, or takes too long to dry. Be sure to check drum support roller kit and shaft before ordering parts.

$10.16

Dryer Drum Felt Seal

This is a drum felt seal for your dryer. It creates an airtight seal between the dryer rear panel and the back of the drum. It is important that this seal be flexible so it does no...

$11.60

Drum Roller Shaft Washer

If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold individually. It is located on the shaft of the drum roller, in the interior of your dryer. To access the drum roller shaft, you will need to remove the front panel of your dryer, and then remove the drum. Before completing this repair, be sure to disconnect the power source from the dryer. Tools required for this repair include a 5/16 nut driver, a stubby Phillips screwdriver, and a pair of snap ring pliers.

$5.58

Idler Pulley Shaft Washer

This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.

$26.76

Tall Baffle

This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle. NOTE: Screws are NOT included.

$25.81

Short Baffle

This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle.

$19.62

High Limit Thermostat (Limit: 200-30)

This high limit/safety thermostat is used on many of Maytag's brands of gas and electric clothes dryers. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 200 degrees Fahrenheit. The element will kick back in when the temperature drops to 170 degrees Fahrenheit.

$16.71

Door Switch Kit

This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start,...

$14.78

Door Catch Kit

This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appliance to both start and complete a full drying cycle. There are two pieces included in this kit, one catch, and one strike. You open and close the door on such a regular basis that this mechanism can wear out. It is a fairly common part to replace. You will need to remove the door of your dryer to install the replacement catch assembly.

All Parts for the MDE16MNDZW
1-14 of 146