Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDBTT60AWW > Instructions

MDBTT60AWW Maytag Dishwasher - Instructions

All installation instructions for MDBTT60AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDBTT60AWW
76-90 of 796
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door would not close because latch was not working

  • Customer: Michael P from Greenville, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
I turned off the electricity at the circuit breaker. Sitting in a chair in front of the opened dishwasher with the partially opened door resting on my knees, I removed the 10 screws lining the inside of the door (setting them in order on the cabinet above -- 2 are different length so this helps keep them in order.
I tilted the inner cover on the door up (which is what the screws had been holding). With the door not fully open because it was on my knees, I was able to position the cover so that I did not have to remove the connection to the soap dispenser.
The two middle screws removed earlier were the screws that held the latch in place, so the assembly was already loose at this point. I put a black mark on the assembly to mark the side that the black wires were attached. Then with the pliers removed the plugs that were connected to the switches on either side of the assembly. Then marked the replacement assembly with the black mark on the same side as the one removed. I attached the plugs to the the replacement assembly using the black mark as reminder for which side was which.
I lined up the latch on the door where it goes, lowered the lid (lifting the lower edge over the base a little), lined up and started the latch screws (middle 2), then started all of the other screws and then tightened them all. Closed the lid and tested the latch. It was closing correctly now. I turned on the electricity and tested to make sure all was now working properly.

Dishwasher wasn't heating the water and dishes were not getting clean.

  • Customer: Victoria from Greenleaf, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
This isn't a how to fix it....it's what part was bad. I had originally contacted the local Maytag repair center and the owner swore up and down that our problem had to be the thermostat and not the heater. He said he had only replaced maybe 5 heaters in 15 years. But our heater looked like heck, with hard water deposits and all, and it wasn't that old, but we went ahead and ordered the thermostat from PartSelect, which came in a day. The problem wasn't the thermostat, so we ordered the heater from PartSelect (again, only one day delivery) and our dishwasher is working again. The heater coil actually had a hole in it from some sort of corrosion. My 18-year-old son did the repair job in a jiffy.

Wheels in upper rack track broke

  • Customer: Bill from Midland, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 9 people found this instruction helpful
The big problem is that you cannot purchase the wheels only. I found that out after ordering the rack track because that looked like what I needed. But it didn't come with the wheels. So I returned it. Then I went to the basement and found things in my junk boxes and fixed it without purchasing the complete parts. Cost: 10 cents for two nuts vs $60 for the required parts.

Broken Door Latch

  • Customer: John from Aurora, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
First, I recommend asking PartSelect for help to insure you have correct part. They tell me the pictures on the web site are provided by Maytag and are copywrited so they can't change them. The pictures are incorrect and misleading. However, it's a known problem, so the PartSelect people will steer you in the right direction. Bottom line in my case, I needed the lower cost part that included more pieces (counter-intuitive so I was glad I called). Got the right part the first time in about 3 days regular shipping.

As far as install, you need a "Torx" screwdriver (screw heads have a star-like pattern) to remove the screws along the inside of the door. From there, the old latch is accessible and easy to remove. As others have mentioned, the hardest part is removing the wire harnesses on either side of the latch. They have a slide on compression clip holding them on, and I think that time and ambient moisture must cause them to get stuck very tightly. I originally thought there was something locking them on, but in the end, I was able to pull and wiggle them loose with by applying slight inward pressure on the prongs with long nose pliers. You have to be careful not to damage the parts when attempting to pull them apart. It's nice that the part I ordered includes new switches, so if I caused any damge removing the old ones, it didn't matter. Just take extra care on the side with the wires and plastic connectors, since those parts aren't included and are more involved to replace if you damage them.

Overall, a very simple repair. The repair stories from others on the site were very helpful and gave me confidence when I ran into the small snag mentioned, since others had the same problem. Hopefully the additional detail I've provided on that issue will help fill any gaps.

Lower basket was dry rotting

  • Customer: Barbara from Ballwin, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 10 people found this instruction helpful
Not being very computer literate, the most difficult part of the entire venture was navigating your web site. But I finally found the part I needed. I paid on line with a credit card, and received the part within a few days. I popped it in the dishwasher, and it took three days before my son noticed it.
He was surprised and I was proud to say " I ordered it on line."
All's well that end's well.
I would difinately use your service again.

Silverware basket had broken through on the bottom and silverware would not stay in. Handle was tricky to put on. Bottom rack one of the adjustable racks had broken.

  • Customer: Suzanne from Jackson, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 16 people found this instruction helpful
Basically took out of box and put in dishwasher.

If you don't hold door when opening, it will drop down hard

  • Customer: Peter from Westbury, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 7 of 10 people found this instruction helpful
First I removed two bottom plates (two screws on each) Then I pulled dishwasher out about six inches. That's as far as it would go because I did not disconnect the water and drain hoses. That was enough to remove the broken cable and collect the disabled spring. I then reattached the new cable to the spring and reworked them into position. NOTE: There is a right and left cable and spring set-up. I used the "good" side as a guide. I then pushed the dishwasher back into place and replaced the two bottom plates.

Dishes not getting clean - sandy residue on dishes.

  • Customer: Todd from Racine, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
There was a tear in the fine filter (fabric) on the accumulator. This can be seen by looking in dishwasher without having to disassemble anything. Food was being sucked in and sprayed back out on dishes.

Disassembled, cleaned, replaced part then reassembled.

Cleaned out the spinning sprayers -- used toothpicks to clean out holes, flushed with water.

Cleaned out under the accumulator.

Works like new.

Latch Assembly Mechanism Broken

  • Customer: JOHN from GAINESVILLE, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
If you have already figured out what the problem and the part number is, and have gotten this far, then you probably already know how to fix it and do not need instructions. But if you do, I took the following steps:

1) Use a #T20 star bit to remove the screws from the inner door panel. [Note: I would use a manual screw driver as opposed to a drill/driver, because you are less likely to accidentally strip the threads in the screw holes];

2) Lift the panel up and detach the wire harnesses from the metal receptacles attached to the old assembly.

3) Remove the old latch assembly, and then press the wire harnesses into the metal receptacles on the new assembly. [Note: You may have trouble getting the wiring harnesses out. If you pull hard enough you can get them off, but if you truly cannot, simply detach the metal receptacles from both the new and old latch assemblies and place the old metal receptacles on the new assembly with the wire harnesses still attached. If you choose this method, be careful with the little plastic retainer bars that secure the metal receptacles, they are pretty easy to break.];

3) Put the new latch assembly in its seating and re-secure the inner door panel. If you used a drill/driver before, I would really switch to a manual driver at this point.

4) Take the dishes out of your bathtub, and place them in the dishwasher.

5) Close the door back.

6) Stare.

original basket fell apart

  • Customer: D from Villas, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

Low water pressure during wash

  • Customer: John from Thornton, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 6 of 8 people found this instruction helpful
Removed filter cover and filter and found the plastic chopper sleeve was stripped out. Followed instructions that came with the seal kit to replace it.

Top rack dishes were dirty.

  • Customer: Edward from Springfield, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
Removed assembly holding the docking station to insure the passageway was clear. I reversed the flappers and noticed an improvement in cleaning then decided to order a new part. Installation was simple and the repair seems to have worked well.

wheel axle broke on one of the 4 wheels that supports the top rack

  • Customer: Helen from Camas, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 6 of 9 people found this instruction helpful
I followed the directions in the dishwasher manual how to remove the top rack of the dishwasher, basically removing the stops on each side, and I set the rack on the counter. I replaced both sides even though one had not yet broken. To replace the part, 5 screws had to be removed; I used an allen wrench. The replacement location of the part was pretty obvious once the screws were removed. The inside of the plastic piece that was opened in the process of removing the defective part was dirty so I took some time to clean that out before attaching the new part. The actual unscrewing and attaching the new part probably took 10 or 15 minutes per side. It took a few tries to get the height adjusting lever to move freely before I tightened the screws. The rack works great now.

The spinning wash arm above the glass rack broke off

  • Customer: Cynthia from Van Nuys, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
The part broke off a while ago, and I did not want to call a repair person. The machine still ran, so I ran it with the part missing - the glasses were not very clean, but the repair call was expensive...

I figured that I had a snowballs chance of finding the part number on a molded plastic piece with no numbers printed on it. Boy was I wrong. I was able to choose the part off of a schematic of my machine right on the website and it linked me to the right part order form, so I did not even have to go back and find it on a list.

When the part came, all I had to do was unclip the old mount- with my fingers- no tools, and snap in the new part.

A for maytag for making it easy to fix
A+ for PartSelect for making it so darn easy

Leaks out and below the front door

  • Customer: John Todd from Franklin, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 9 people found this instruction helpful
First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.
All Instructions for the MDBTT60AWW
76-90 of 796