Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDBTT60AWW > Instructions

MDBTT60AWW Maytag Dishwasher - Instructions

All installation instructions for MDBTT60AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDBTT60AWW
616-630 of 796
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishes not getting clean

  • Customer: Lesley from Saint Louis, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We recently purchased a new home and it didn't matter how hot we ran the water in the sink before starting the dishwasher, the dishes, especially glasses, were filthy. Extra rinse cycles, pots and pans cycle, nothing worked. After finding this site, we took the chance on what the troubleshooter recommended and bought the accumulator filter and wash impeller. The parts came so fast! We followed the videos on this site step by step and we were successfully able to replace the filter and impeller. The impeller was COATED in nasty slimy grossness; it was obvious the previous owners never rinsed their dishes before running the dishwasher. After replacing these two parts, we have clean dishes! We have switched from tablets to liquid detergent which also helped (not sure why, tablets have worked at our old house just fine).

Dishwasher left residual water at end of cycle.

  • Customer: Mark from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Very straight forward repair. Parts Select provided the right part with very timely (regular FedEx)delivery. Repairclinic.com provided excellent video to show basic repair steps. Suggest using a "star" tip screw driver to disassemble interior parts of the machine to clean out years of gunk which will reduce the chance that the drive motor will bind/fail (which mine did and which saved me the cost of a new motor or new dishwasher). Upon reassembly, be sure to check water supply copper compression fittings for leaks that moving the machine can cause. Place pads under "feet" of machine to avoid marring wood floor when moving machine.

Broken door latch handle.

  • Customer: Harvey K from Sun City Center, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed video. Undid about 10 screws on door. Lifted inner door park disconnected two wires, put in New latch put back screws and Bob's your uncle. Phone clerk most helpful and delivery could not have been faster. Next day!!!

Unusally noise

  • Customer: Gregory from North Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove and replace a washer impeller. Simple

Dishes on bottom rack not clean

  • Customer: Kathryn from Apopka, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I examined the arm on the floor of the dishwasher and found that it had collided with something sticking through the bottom of the lower rack. One of the jets on the tip of the arm, which was supposed to spray sideways to make the arm spin, was missing its top and now sprayed up. This put the arm off balance and kept it from spinning. I ordered a new arm from PartSelect. It arrived much sooner than I expected. With the pliers, I unscrewed the nut holding the arm on, replaced it with the new arm, and refastened the nut. The next time I used the dishwasher all the dishes on the bottom rack were clean.

Whirlpool has a known flimsy latch design. It broke

  • Customer: Joe from Kalamazoo, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The discontinued the latch alone, so you must buy the entire micro-switch and latch assy. You take off the door screws with the Torx driver, prop the inner panel temporarily out of your way, fight the terminal connectors OFF the old micro-switches w/needlenose pliers, slid the new connections ON, lay the assy in it's "slot" (which IS well engineered) carefully replace the inner door panel, start a few screws, make sure it's aligned at EACH screw and tighten. TA-DAH. Did I mention turn the power OFF first?? It may bite ya.

Broken door latch

  • Customer: Mathew from Port Angeles, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
With the door open to the dishwasher I remove the inner cover with the appropriate screw driver. I then removed the two electrical plugs from the latch and lifted it out of the door. The new piece went back in reverse. Took less than 15 minutes.

Plastic handle retainers broke

  • Customer: Christopher from Suttons Bay, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Simply removed the interior door panel liner by removing several screws. Unplugged the handle from the switches and removed from equipment. Plugged in new handle which came with switches and reinstalled the interior liner panel. Simple as that !! Very, very easy. I did however have to remove the vent to take off the interior panel and in doing so broke some little plastic part that was not available for purchase separate from the entire vent unit. In the end I needed a $27 handle, but had to buy a $49 vent - it still cost less than the service call alone !! And, the delivery was super fast - unbelievable !!! Probably faster than the service man !!!!

Top washer arm clip broken

  • Customer: Christopher from Elgin, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Used flat blade screw driver to unclip the holding bracket. Snaped new bracket and wash arm on. Took all of about 30 seconds.

Silverware basket replacement

  • Customer: Mike from Wheat Ridge, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The silverware basket in my Maytag portable dishwasher was pretty flimsey. The replacement basket I got here seems more durable and I'm very happy with the quality. Shipping was fast and it was packaged very well!

Dishwasher would not proceed through a cycle.

  • Customer: Putnam from Valparaiso, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
1.Shut off electric power. 2. Remove 11 torx screws around the inside door panel. 3. Unplug connectors on control board. 4. Remove control board from the door. 5. Install new control board in the door. 6. Install connectors on control board 7. Install 11 torx screws around the inside door panel. 8. Turn on electric power. 9. Run the diagnostic program listed in the instructions to be sure the cycle completes properly.

broken door latch

  • Customer: Vincent from Germantown, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Turn off circuit breaker to dishwasher. Remove door panel screws and store in soap dispenser. Remove contact wire connector with needle nose pliers. Replace latch, hook up wires, set switch in place, replace panel and reinstall door screws. Done.

Door latch replacement was quick and easy

  • Customer: Kenneth from Selma, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Was easy to find the right part and place the order was delivered quickly and on time. Installation was quick and easy. Great info on the web site. Thank you!

Water leak right front

  • Customer: Mark from Tallahassee, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Simply removed switch and float a d replaced them. A real no brainer!

Upper and lower racks had broken and rusting prongs.

  • Customer: Edith from Lancaster, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old racks -- easy. New lower rack slid right into proper position. Upper rack -- had to unclip the rotating water supplier from underside of old rack and position it on the underside of the new rack, carefully noting the removal process to facilitate re-placing the water supplier onto the new rack. No tools needed -- very easy. New upper rack slid right back into proper position.
All Instructions for the MDBTT60AWW
616-630 of 796