Models > MDBTT60AWW > Instructions

MDBTT60AWW Maytag Dishwasher - Instructions

All installation instructions for MDBTT60AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDBTT60AWW
16-30 of 793
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Inlet Valve due to freezing - water leak

  • Customer: Craig from Old Orchard Beach ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 40 of 41 people found this instruction helpful
Most of the time was spent pulling out the dishwasher from under the counter, as a new tile floor had been installed after the DW was installed.

Great pictures of components on this website confirmed what part to order.

Shut off water feed to DW and disconnect power to DW.

Unplug wire connector to old valve (solenoid) and disconnect water inlet hose. Observe that valve is attached to sheet metal bracket.

Remove bracket, with valve attached. Don't remove valve from bracket. New valve comes with sheet metal bracket.

Remove female threaded adaptor (brass) from back of old valve and screw on to new valve using Teflon tape. That is the only piece you need to reuse.

Attached the new bracket (with valve attached) to DW. Attach water inlet hose. Attach plug to new valve.

Turn on water to DW. Check for leaks. Retighten hose connection if required. Run dishwasher. Keep lower panel off for a couple of days to be certain no leaks develop.

Plastic wheel fell off and melted

  • Customer: David from sleepy hollow NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 66 of 127 people found this instruction helpful
Stuck new wheel on, time to find and order part on partselect 2 min, time to open package and install part 1 min.

Total job 3min.

Wash motor not pumping and making a grinding sound

  • Customer: George from Poughkeepsie NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 27 of 33 people found this instruction helpful
I went to PartSelect and found the parts pictorial. A replacement motor was listed for 3 series of the dishwasher. The series can be identified by the first 2 digits of the dishwasher serial number. Mine was 22 so I needed parts for the series 20 dishwasher.

According to the pictorial it looked like the motor seals were included with the replacement motor. When the motor arrived, I found the seals were not included. I called PartSelect and they shipped the seals to me with free overnight delivery.

I had no trouble disassembling the wash manifold and spray parts using the instructions provided with the replacement motor and the instructions from the Maytag repair manual that I found online. The motor is removed from the inside of the tub.... very nice. You don't need to remove the dishwasher from under the counter in order to get at the motor.

I made a mental note of the orientation of the faulty motor before I removed it. I installed the replacement motor with the same orientation along with the wash parts. The dishwasher worked successfully.

Thank you PartSelect.

Would not spray.

  • Customer: Frank from Raleigh NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 26 of 37 people found this instruction helpful
Looks like Maytag knew this was a problem. My chopper sleeve (plastic) was stripped and causing the impeller to not spin. The replacement part was all metal and was very easy to replace the old one just by removing screws. The replacement looks to be very sturdy and should last a lot longer than the original. Thanks.

Leaking at bottom of door

  • Customer: E L from Seeley Lake MT
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 19 of 20 people found this instruction helpful
The initial repair was more involved due to figuring out how to get at the problem. A foam sealer strip located at the bottom of the inner door had lost it's seal. I first sent off for one and it was of relatively thin material. It was carefully installed but still leaked. I ordered another one from Part Select and it had thicker foam. It was installed right over the previously installed strip and made a tight seal. (knock on wood)

Dishes were coming out dirty with specs of debris on them

  • Customer: Eric from Newton WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 20 of 23 people found this instruction helpful
I noticed there was a filter type of material in the bottom of the dishwasher that had a small tear in it and figured that was my problem. I removed the nut from the sprayer arm at the bottom of the tub, removed the sprayer arm, removed 3 screws of the plastic cover below that. Removed six screws on the plastic cover below that. Removed one screw fron the center of the black pump spinner wheel that allowed me to lift off that cover. Then I lifted out the flowplate assembly. Placed the new part in and reversed the steps. Works like new again! All for about $30...I am not trianed in any way and have no experience in this kind of thing but am motivated trying to avoid a large service bill for a few screws. I am so happy...Thanks PartSelect!

Dishwasher wouldn't drain.

  • Customer: mark from pearland TN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 19 of 21 people found this instruction helpful
It was very simple. After disconnecting the dishwasher, I pulled it out from it's space under the cabinet and turned it over on it's side. The pump twists into place and is held by two small bolts. It's very easy to get to and nothing else needs to be taken apart or disconnected. Used some silicon sealant to hold in place after replacing the pump and waited 24 hours to run. The pump was the problem and the dishwasher now runs fine.

Latch handle broke off

  • Customer: James from Madras OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 18 of 20 people found this instruction helpful
Once I got the door open, I removed the door cover screws with a Torx driver, where I found the broken handle and the Latch Assembly. One of the plastic handle pivot points had broken clean off. In my Brilliance, I went online to PartSelect, found that the part that I needed had been discontinued (from Maytag) and picked one that looked right. It ended up being the assembly without the handle, the part I needed. Save yourself some time and call the 800 number to make sure you get what you need. They were very helpfull in returning the wrong part to get the right one. Once I had the part, the repair was very straightforward. I just had to open the door up again, swap in the new Latch Assembly with the steel reinforced pivot point handle, and put the screws back in the door. The latch assembly is held in place by two of the door screws. Watch the cut off switches on the assembly, the power is hot until you power off the circut at the electric panel.

leak in front right corner

  • Customer: Jessica from Lovington IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 18 of 22 people found this instruction helpful
I had to remove the 4 screws holding the toe panel. Then I had to take out the one screw holding the floater switch housing in place. It snapped open to release the floater and that just lifted out. I put the new float in and snapped the new housing on. I put the screw back in to hold the housing in place attached the two wires to the switch and put the toe panel back on. It was all very easy to do and my first home repair went very well. thank you.

A storm power surge "fried" the main circuit board

  • Customer: Ronald from Cass Lake MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 16 of 17 people found this instruction helpful
I separated the door from the interior door liner by unscrewing the "torx" screws along the edge of the door interior (about 12 screws). I unscrewed the circuit board cover and removed the old circuit board and disconnected the wiring harnesses that attached to the circuit board. I reconnected the wiring harnesses to the new circuit board, put the circuit board back into its holder and cover and reattached the door liner to the door. I flipped the house circuit breaker for the dishwasher power on and turned the dishwasher on. It works like a charm!

the bottom dishrack beginning to rust

  • Customer: margaret from san diego CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 16 of 17 people found this instruction helpful
the new dishrack fit right in immediately with no tools needed. Delivery was prompt

Dishwasher wouldn't stay on without pushing on door due to faulty switch.

  • Customer: Andrew from Azusa CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 21 of 32 people found this instruction helpful
Removed plastic lining from dishwasher door with torx screwdriver, then removed screw holding door latch assembly in place. Removed existing switch from door latch assembly and replaced.

This switch was not the correct one initially as it was a normally closed switch, whereas the existing switch was a normally open. Was able to pry open the switch and switch the contacts to normally open so it worked out in the end. Would recommend purchasing the complete latch assembly w/ switches if you aren't comfortable taking the switch apart.

Dishwasher would fill properly but when wash cycle would start you could not hear any water spraying.

  • Customer: Timothy from Trevor WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 16 people found this instruction helpful
First I removed the lower spray arm by removing the middle retainer nut. Next remove the 3 screws holding the outer shroud in place. Next remove 6 screws holding the water pump top housing in place. Under this housing you will find the impeller which is retained by a screw. Check the impeller closely for cracks especially near the center hex portion of the impeller. Replace if you have any doubt of it's integrity. Next remove the lower pump housing that has the screen material in the center. What I found was the nylon part that attaches to the shaft of the motor was stripped so the impeller would spin in it's normal direction ( counterclockwise) but under the load of water it would not. So I ordered a new impeller and seal kit with a metal sleeve and chooper blade. Follow the instructions provided in the new kit a reassemble accordingly.

washer stopped working.

  • Customer: Nick from Fenton MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 14 of 14 people found this instruction helpful
Removed screws on the interior of the door. Lift panel up and remove two wire clips, lift panel completely off. Unscrew one screw on the bottom of control box and remove cover. Unplug all wires. Push retaining tabs out from inside the box and lift the control board out. Install new control board by sticking back end in first,then snap into place. Finish by installing everything in reverse order. Done.

The dishwasher would not drain

  • Customer: Brian from Keokuk IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 16 of 22 people found this instruction helpful
First of all I shut the power off to the dishwasher at the breaker box. Turn the water off to the dishwasher. Unhook the water line and then remove the screws that go around the outside trim edge of the dihwasher that secures it to the cabinets. Then you will want to look at the adjustable legs on the dishwasher. You may need to lower the legs to get the dishwasher out from underneath the counter top. While you are doing this you should also pay attention to your drain hose. My drain hose had plenty of slack so I was able to pull my dishwasher out from underneath the cabinet and then unhook it. You should have towels or a bucket in place to catch any water that is inside the drain hose. Next I laid the dishwasher over on its left side and I was able to access the pump. I then used a flat screw driver to remove the hose clamp and remov the drain hose from the pump. I then unplugged 1 wire connector and a bracket and could turn the pump counter clockwise and removed it from the dishwasher. There is a bracket that must be removed from the old pump to the new pump. Once this is accomplished You are ready to reinstall the new pump. I took a towel and wiped the area where the pump hooks into the dishwasher to make sure all debris was removed. I then used a very small amount of gasket sealer and placed it around the "O" Ring on the new pump. Next place the pump back in the whole and turn in a clock wise direction securing it back into the dishwasher. Hook up the drain hose and the wire connector. Make sure the bracket is postioned properly and you are ready to put dishwasher back under the counter.
All Instructions for the MDBTT60AWW
16-30 of 793