Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDBTT59AWW > Instructions

MDBTT59AWW Maytag Dishwasher - Instructions

All installation instructions for MDBTT59AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDBTT59AWW
31-45 of 808
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

A mouse had chewed on the inlet cover to the point that it would no longer stay in it's hole.

  • Customer: Melissa from Wales, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 22 of 27 people found this instruction helpful
Simply popped the new cover in. My part by the way was really easy to identify on the website, easy to order and arrived in a very timley fashion!

latch broke completely and then shortly thereafter due to the extra pressure put on the control panel handle lip the top part of the panal broke off.

  • Customer: KEVIN from Woodbury, MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 21 of 25 people found this instruction helpful
removed all screws that held the door liner in place @ 10 then removed the 6 screws that held the control panel in place. control pane came off easily. as the latch was broken that came off easy too. The replacement panel and latch fit perfectly. the only trouble I had was inserting the flat wiring bundle from the new control panel to the old circuit board connector. Take your time and really seat the flat wire bundle into the circuit board. it needs to be nice and snug. if it's not only a few of the wash functions will light up when pressed. once the connection is tight all functions worked. replace all screws - easy.

Broken door latch

  • Customer: Leonard from Plant City, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 20 of 23 people found this instruction helpful
The repair stories on PartSelect.com told me exactly what to do.

First, I checked the inside of the door and confirmed that the inside panel of the door was held in place with about 10 torx screws.

Second, I went out and bought a set of torx screwdrivers.

Third, I TURNED OFF THE POWER TO THE DISHWASHER AT THE BREAKER BOX! Safety first!

Fourth, I removed the screws and gently lifted the inside panel of the door, and then gently lifted the broken door latch assembly out of its slot. (There were no more screws to remove, because the latch assembly is held in place by two of the door screws.) Two sets of wires, one white and the other black, were connected to the latch assembly by plug-in connectors.

Fifth, I unplugged the wires from the broken latch assembly. The clips in the plug were very tight, so I used a dishtowel to hold onto the latch assembly. I found that gave me a better grip.

Sixth, I plugged the wires onto the new latch assembly, and then slipped the latch assembly back into the slot.

Seventh, I replaced the inside door panel, and replaced in the 10 torx screws.

Finally, I turned on the power at the breaker box, closed the door, and turned on the dishwasher. It ran perfectly!

I would like tyo add that I had ordered an unnecessary part by mistake. I called the return number, and the person who answered was extremely helpful. She gave me the return authorization number and I put the part in the mail. Ten days later, I received an email from PartSelect.com confirming that the part had arrived and that my account had been credited.

The entire process was easy and pleasant. Anybody can do this! Just make sure to shut off the power at the breaker box before you start on the job.

dishes still dirty, soap remained in dispenser.

  • Customer: Hans from Show Low, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 20 of 25 people found this instruction helpful
After repairing this dishwasher 5 times during the past 8 years this one was real easy: Open door, unscrew inside cover and carefully move over to one side. Unplug soap dispenser, unscrew soap dispenser and remove. Fit new dispenser, reconnect it, put inner cover back in its place and secure it with the retained screws and you are back in operation. Hans.

grinding noise during cycle

  • Customer: rich from liberty twp, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 17 of 18 people found this instruction helpful
took the bottom spray arm & lower plastic pieces out, unscrewed the impeller & replaced it. the original impeller which holds the disposal blade down & wore down & no longer retained the blade. snap.

Door leaks

  • Customer: ROY from SUFFOLK, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 18 of 21 people found this instruction helpful
Replaced the door seal. Removed the old seal and gently stretched the new seal and pushed it into the channel. Snipped off about 2 inches excess seal. As far as the Inner Door Foam Insulation Strip goes, it was not as easy. To begin with, the old Foam Strip was attached to the door insulation and not the door. The attempt to remove the old Foam Strip from the insulation became cumbersome, so I just attached the new Foam Strip on top of the old Foam Strip. So far, after a few cycles, it appears that it corrected the leak.

The dishwasher would not drain

  • Customer: Brian from Keokuk, IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 19 of 27 people found this instruction helpful
First of all I shut the power off to the dishwasher at the breaker box. Turn the water off to the dishwasher. Unhook the water line and then remove the screws that go around the outside trim edge of the dihwasher that secures it to the cabinets. Then you will want to look at the adjustable legs on the dishwasher. You may need to lower the legs to get the dishwasher out from underneath the counter top. While you are doing this you should also pay attention to your drain hose. My drain hose had plenty of slack so I was able to pull my dishwasher out from underneath the cabinet and then unhook it. You should have towels or a bucket in place to catch any water that is inside the drain hose. Next I laid the dishwasher over on its left side and I was able to access the pump. I then used a flat screw driver to remove the hose clamp and remov the drain hose from the pump. I then unplugged 1 wire connector and a bracket and could turn the pump counter clockwise and removed it from the dishwasher. There is a bracket that must be removed from the old pump to the new pump. Once this is accomplished You are ready to reinstall the new pump. I took a towel and wiped the area where the pump hooks into the dishwasher to make sure all debris was removed. I then used a very small amount of gasket sealer and placed it around the "O" Ring on the new pump. Next place the pump back in the whole and turn in a clock wise direction securing it back into the dishwasher. Hook up the drain hose and the wire connector. Make sure the bracket is postioned properly and you are ready to put dishwasher back under the counter.

Latch Handle was broken from inside

  • Customer: Richard from Franklin, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 18 of 26 people found this instruction helpful
1st: Unscrewed the inside of the door (actually hex screwdriver needed).
2nd: Removed broken part (one side of handle latch (which is plastic) was broken.
3rd. Had to disconnect two electrodes that were attached to the part that held the handle (there are two small prongs that you need to push back to remove these)
4th. In order to place the handle on the groove, you need to pull apart the bottom of the housing piece (it looks like it would be a hinge, but you just pull it apart)
NOTE: Make sure you have another person hold the top portion when you pull this apart because it has a spring and will come completly apart. This happened to us and it was a pain to get it back together.
5th: place the smaller "clamps" plastic pieces in the grove and then it should slide down into the groove, which will also seat the outer "plastic clamps" into the grooves.
NOTE: It seems like the repair part was built to reinforce this part of the handle, since this was the part that broke before. It is now reinforced with a little metal rod on each side.
6th: After all that, you need to place the two electrodes back on the piece.
7th: Hold it in place and put the inside of the door back on (start a screw on one side and then go to the opposite side. This will help to align the screw holes).
8th: After I put it all back together, I turned it on to make sure it worked ok.

Broken Dishwasher Door Latch - Assembly Replacement

  • Customer: Gail from Sharpsburg, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 17 people found this instruction helpful
Being a fairly technical female, I decided after Internet research to replace this part by myself. It could not have been easier - even after reading several Internet horror stories. I believe the major difference being I replaced the entire assembly, not simply the latch.

You need a hex-head allen wrench to remove the inside cover of the dishwasher door, and some sort of pliers to remove the old unit. I used vice grips since I am a wimpy girl - they worked nicely (this took the longest time).

Step by Step:

Turn off the power to your dishwasher.

Remove the door screws and carefully lift it to access the door latch assembly.

Remove the old door latch by unplugging the black and white electrical mechanism. Pay close attention to which side the black and white connections are removed from for reconnection reasons. This is where I had to use vice grips. It took a bit to "unplug" the old latch assembly.

Once the old latch assembly is removed, position the new latch assembly and reconnect the electrical source.

Carefully reposition the door and replace the screws.

Turn on the power.

Run a short cycle (I used rinse) to make sure that the unit was replaced correctly.

Can it be any easier than that??

broken door springs

  • Customer: jeffrey from holland, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 15 of 19 people found this instruction helpful
I pulled the unit from under the counter. the springs and cables are on the front sides of the dishwasher. I moved the insulation removed the broken spring and cables and replaced them with the new parts. just one side was broken, but I replaced both while I had the unit out.

The basket in our dishwasher had many broken parts on the bottom and the silverware kept falling through

  • Customer: Marge from Cranford, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 14 of 16 people found this instruction helpful
We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.

Broken handle/latch Dishwasher was very difficult to open.

  • Customer: George from Andover, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 14 of 16 people found this instruction helpful
The first thing I did was read the all of repair stories that others had submitted. Then I set the timer and chucked up the Torx bit in my electric drill/screwdriver. There are 10 Torx screws on the inside of the dishwasher door and they came out very quickly. The top two screws hold the latch in place. I lifted the inside stainless steel cover to get acces to the latch. There was enough slack in the wire that I was able to remove the latch from where it was and extend it above the door. This let me lay the stainless steel liner back onto the inside of the door without removing or disconnecting the soap dispenser. Thus exposed, disconnecting the connectors from the old latch and reconnecting them to the microswitches on the new latch was a breeze. Once connected, I reinstalled the latch assembly, repositioned the liner correctly and replaced the ten screws. The entire job, including putting my tools away and cleaning up took eight minutes. I did it on my lunch break. The eight minutes included pulling the circuit breaker and reconnecting it (very important, that step). The new latch/handle assembly completely fixed the problem.

Dishwasher handle broke

  • Customer: Christy from Warm Springs, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 14 of 17 people found this instruction helpful
This was a very easy repair. Before I did anything, I flipped the breaker for the dishwasher and tried to turn the dishwasher on to make sure it had no power going to it. Once I was certain the power was off I removed the hex screws (there are 11) on the inside of the door panel using the hex screwdriver. Lifting and holding the inside panel up, I then used the pliers to pry the old latch assembly out of its metal prongs. Then I replaced the old latch assembly with the new one, pushing the metal prongs (by hand) into the slits of the new latch assembly. Last, I lined everything up and screwed the door panel back in place. I flipped the breaker back on and activated my child lock to make sure I had power. The handle worked perfectly. Quick and easy fix!
I ordered the part with 3-5 day delivery and actually received it in 2 days! I'm extremely pleased with my partselect.com experience and highly recommend using them for all your appliance parts needs!

silverware basket broken - replaced with new one

  • Customer: Linda from Owasso, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 13 of 14 people found this instruction helpful
I was able to remove the old handle and place it on the new basket - using only a screw driver.

Water leaking from bottom of dishwasher at motor.

  • Customer: Jack from Lee's Summit, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers
  • 12 of 12 people found this instruction helpful
I removed the lower wash arm held by a single center plastic coated nut with pliers.

I then removed the six pump housing screws and the three filter cover screws.

This allows access to the pump impeller which is held by one screw. Once it is removed the filter plate, chopper and motor seal can be removed.

I actually had done this before to find a noise. At the time I noticed the impeller had become shorter due to plastic breaking off the impeller. It still fit the motor shaft so I just cleaned out the plastic and screwed it back on. I did not check for water leakage until I noticed loose flooring material a couple weeks later.

This is the mistake I made. The impeller is made so it presses down upon the motor shaft seal expanding it to seal out water. Because the impeller was missing the lower skirt it was too short to but enough pressure upon the seal to stop leakage.
Never use a impeller which is damaged in any way.

Due to this error I have had to buy a motor assy also. It was destroyed by the water.
All Instructions for the MDBTT59AWW
31-45 of 808