Models > MDBH955AWS > Instructions

MDBH955AWS Maytag Dishwasher - Instructions

All installation instructions for MDBH955AWS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDBH955AWS
31-45 of 895
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The basket in our dishwasher had many broken parts on the bottom and the silverware kept falling through

  • Customer: Marge from Cranford NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 13 people found this instruction helpful
We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.

grinding noise during cycle

  • Customer: rich from liberty twp OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 13 people found this instruction helpful
took the bottom spray arm & lower plastic pieces out, unscrewed the impeller & replaced it. the original impeller which holds the disposal blade down & wore down & no longer retained the blade. snap.

Latch Handle Broken

  • Customer: Edward from Fredericksburg TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 11 of 11 people found this instruction helpful
This repair was very easy. First, I opened the dishwasher, removed the screws (they are torx) and removed the old handle assembly. I removed the inner liner from the door, and to do that I had to pull out the electrical wires. I turned off the power, always a good idea. I should have marked the polarity on the plugs before removing them, since you can put them back on wrong (and I did).

I also used caulk to hold the assembly on the bottom, since the cheap plastic molded forks holding the assembly on had broken. Most of the holding force comes from screws at the top. The caulk provides just a little adhesion, and will be easy to remove if the handle should need to be removed again--which I consider unlikely.

water was dripping from the bottom of the front loading door. Over time this had seeped into the insulation foam strip and formed a solid encrustation within the foam strip.

  • Customer: Dan from Clarkston MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
The real cause of the leak had nothing to do with the foam strip. The latch for the front loading door at the top needed to be adjusted to hold the door in tighter to the rubber door seal. This simple adjustment stopped the leak but since the foam seal was all encrusted with dried detergent from probably years of absorbing the leak, I replaced it with your new foam strip. I used a screw driver with torx bit and removed the stainless screws holding the inner door to the outer door. Once these were separated I removed the old foam strip using a putty knife and lacquer thinner. Placing the new strip onto these cleaned surfaces was the easiest part of the whole repair.

Door leaking, handle broken

  • Customer: John from Warren MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 11 of 13 people found this instruction helpful
Door gasket was easy out and in using the white mark on the seal to line it up with the center. The latch came with the handle so I returned the extra latch assembly that I ordered. Super easy to install. Removed door screws, carefully lifted and set aside inside of door leaving wires attached. Reved wire from latchtch switches, attached wires to new latch, put in postion and reassembled.

Water leaking from bottom of dishwasher at motor.

  • Customer: Jack from Lee's Summit MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers
  • 10 of 10 people found this instruction helpful
I removed the lower wash arm held by a single center plastic coated nut with pliers.

I then removed the six pump housing screws and the three filter cover screws.

This allows access to the pump impeller which is held by one screw. Once it is removed the filter plate, chopper and motor seal can be removed.

I actually had done this before to find a noise. At the time I noticed the impeller had become shorter due to plastic breaking off the impeller. It still fit the motor shaft so I just cleaned out the plastic and screwed it back on. I did not check for water leakage until I noticed loose flooring material a couple weeks later.

This is the mistake I made. The impeller is made so it presses down upon the motor shaft seal expanding it to seal out water. Because the impeller was missing the lower skirt it was too short to but enough pressure upon the seal to stop leakage.
Never use a impeller which is damaged in any way.

Due to this error I have had to buy a motor assy also. It was destroyed by the water.

The panel on the dishwasher stopped allowing choices, then failed completely.

  • Customer: Tamara from New Ipswich NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 11 of 13 people found this instruction helpful
First I flipped the breaker to the dishwasher's outlet since I would need to work around the power supply. Then I removed the bolts that held the door panel in place. I had to carefully push it back because of the power supply wires, but then I put my hand in between the sides of the door and unplugged it so my daughter could hold back the inside part of the door. Next I removed the bolts holding the power supply in place and pulled out the flexible circuit board that connected the power supply to the control panel and moved the power supply to the side. The control panel also had a few bolts which, once removed, allowed the control panel to be removed completely from the door. I then slipped the new one in place and reversed my steps. After flipping the breaker I ran the dishwasher - and it now works as well as when I first purchased it!

Door leaks

  • Customer: ROY from SUFFOLK VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 10 of 11 people found this instruction helpful
Replaced the door seal. Removed the old seal and gently stretched the new seal and pushed it into the channel. Snipped off about 2 inches excess seal. As far as the Inner Door Foam Insulation Strip goes, it was not as easy. To begin with, the old Foam Strip was attached to the door insulation and not the door. The attempt to remove the old Foam Strip from the insulation became cumbersome, so I just attached the new Foam Strip on top of the old Foam Strip. So far, after a few cycles, it appears that it corrected the leak.

Dishwasher not draining

  • Customer: Darrell from Snellville GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 9 people found this instruction helpful
It was my first time repairing a dishwasher. I was a little worried. I also wasn't sure about how to remove the drain pump. Well, the hardest part was just getting the dishwasher out from under the counter. I did find a crimp in the drain line that probably contributed to the original pump going out. I fixed that, removed the old pump by removing one screw holding a stablizer bracket and twisting the pump connection. The original bracket is needed, so I removed it from the old pump, attached it to the new pump and reversed the removal process and secured the pump by reattaching the stabilizer bar with the single screw. I then slide the dishwasher back under the counter. Runs great. Easy repair. The part was shipped and delivered on time. Very impressed with the process and will order my appliance parts from you in the future.

broken door springs

  • Customer: jeffrey from holland PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 10 of 13 people found this instruction helpful
I pulled the unit from under the counter. the springs and cables are on the front sides of the dishwasher. I moved the insulation removed the broken spring and cables and replaced them with the new parts. just one side was broken, but I replaced both while I had the unit out.

dishes still dirty, soap remained in dispenser.

  • Customer: Hans from Show Low AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 11 people found this instruction helpful
After repairing this dishwasher 5 times during the past 8 years this one was real easy: Open door, unscrew inside cover and carefully move over to one side. Unplug soap dispenser, unscrew soap dispenser and remove. Fit new dispenser, reconnect it, put inner cover back in its place and secure it with the retained screws and you are back in operation. Hans.

Door latch failed

  • Customer: ROBERT from ALLEN TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
Turn-off the dishwasher power at the circuit breaker. Open the dishwasher door flat. Remove the 11 screws around the perimeter of the door using a T-20 TORX bit (available at any hardware store). The latch assembly is held on by the top middle two door screws. Pull latch assembly out from top of door. Remove the black and white cable assembly connectors from the latch assembly making sure to note which side each color is on. If you have trouble sliding the connector off, use a flat screwdriver carefully to pry it, but do not pull on the wires. Install cable connectors onto new latch assembly making making sure the black and white cables are on the correct sides. Position the door at a 45 degree angle and place the latch assembly into position while putting the white inner door over it. Reinstall the 11 TORX screws around the side of the door being sure the screws are snug, but not overtightened. Test the operation of your dishwasher. The new latch assembly seems to be built better than the factory original.

Broken Latch

  • Customer: Edward from Charlotte NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 9 people found this instruction helpful
Used torx bit to remove screws on door and removed the back of door. Removed wiring from switches (2) on broken latch and removed latch. Plugged in switches on new latch and placed latch in position. Screwed back of door into place and that was it! Very simple task and new latch looks and feels much more sturdy than old one.

The impeller was not spinning. There was no washing water.

  • Customer: Brian from Portland OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 8 of 9 people found this instruction helpful
After finding out that the impeller shaft was stripped (plastic) I quickly found the correct replacement on partselect.com by using my model number.
You do not have to remove the dishwasher, if you know what is wrong. But, throw the breaker switch and turn off the water! After removing the spin washer arm, Undo all of the torx screws and pull out the plastic filter looking plates along with the center plastic water jet. This jet provides water for the upper washer assembly. You may have to pop that upper assembly out to protect it from damage.
The black impeller should just pull out if the plastic shaft is stripped. Otherwise, unscrew the small torx head and remove the impeller. You can remove the blade at this time and unscrew the plastic shaft by unthreading it while keeping the motor from spinning. (I shoved a screw driver underneath the dishwasher through the motor. Also the motor is just floating on the rubber gasket and can easily pulled out to accomplish this task. It's heavy and has a plug attached to it. You'll see where you can shove the screw driver. This comes in handy while installing the new shaft, because it is metal. Which is a great, long awaited upgrade for the Maytag Quiet Series. Once you find which shaft to use, (which correct inner thread, course or fine), install it with the great directions that come with the part. Putting all the stuff together is not as bad as one would think, there is only one way for it to go back together. After installation is complete, turn water and breaker switch back on. Run a cycle and listen for the washing cycle against the wall of the washer. If you cannot tell the difference, you can unscrew the white lock arm and insert it into the door. Turn it on and watch how a dishwasher works. Get ready to get a little wet. Towels!

Dishwasher heating element bad

  • Customer: Gary from Indianapolis IN
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 8 of 10 people found this instruction helpful
I could not reach the heater element nuts from under the dishwasher so had to pull out the dishwasher. I removed the screws around the front of the dishwasher and pulled it about half way out before the water inlet pipe and the electrical wires stopped me. I shut off the water, unhooked the copper pipe, and unhooked the electrical wires (shut off circuit breaker first). Pulled the dishwaser out so I could remove the element nuts and wires to the element. Removed the old element and installed the new one - the old nuts would not fit. I went to a local appliance parts store and found that my element is no longer made. I had the correct replacement element but you need to order the nuts also. Luckily, the local store had a small brass nut that worked. Reattached the electrical wires to the element, pushed the dishwasher half way in, reattached the water inlet and electrical wires, pushed the dishwasher all the way in and scewed back into the cabinets. All is well now and the dishwasher is working much better.
All Instructions for the MDBH955AWS
31-45 of 895