MDBH955AWS Maytag Dishwasher - Instructions

1. Remove cover screws and lift cover to access latch assembly and lift out. 2. Pull off switch plugs with pliers. 3. Lube contacts on new assembly with petroleum jelly and push on switch plugs. 3. Place assembly in position and replace cover. Note that two cover screws hold the assembly in place.

Handle and Door Latch Assy Installation
Below is my experience installing the assembly

1) Remove rear cover of front door with Torx bits.
2) Remove latch assembly (it is held on by 2 of the screws holding the rear cover).
3) Remove left and right female wire sockets from assembly. (Ensure your power is OFF to dishwasher)BTW, this may take some effort as the socket assembly is tightly connected to the terminals.
4) Discard old assembly and connect both wire sockets to their respective terminals on the new latch assembly.
5) Place new assembly oriented on door screw-holes.
6) Place rear cover on door and replace all Torx screws.
7) Test latch and insure the system will function by going through one cycle.
8) Installation complete

Unscewed 11 scews, unpluged electrical connections, Of course, made sure power was diconnected,replased hander according to website directions, very simple, took ten minutes. Thanks. You saved at least $100.00 dallars

Disconnected power to dishwasher. Removed screws holding inside cover of door. Lifted door cover, unplugged wires from micro switches on handle. Removed broken latch/handle assembly and replaced with the new one. Re-installed door cover.

The only problem I had was the miro switches, didn't have the tool to release the exsisting wires on the old switches so I had to reuse the old ones just by swithcing them to the new handle and every thing works great now. If anyone knows what tool that I need to get the wires off the old mirco switches let me know. craign84601@comcast.net

Turn off power(curciuit breaker) to dishwasher, Removed screws from around inside door edge, then pulled front away slightly pulled latch assembly out about six inches, disconnected wire connectors from handle asembly, discarded old assembly, attached connectors to new assembly, reinstalled in place, replaced screws, turned power back on, closed door repair complete and works great.

Super simple repair, Im glad I read everyones instructions.

I took the screws off the dishwasher door, opened up the panel took out the part & replaced it witht he new part without additional tools. I replaced the screws and the dishwasher worked! Very Easy!

Verry simple. turn off power. remove 11 screws, old latch falls out to be replaced. saved hunderds of dollars not having the repair man come out. Thank you for your low cost part.

removed door panel replaced handle reassembled

very simple repair. if i had to do it again i could do it in under 5 mins. it takes longer to remove the screws then it does to replace the latch. just remove the screws ( i left the bottom ones in on the left and right side, no need to remove them). then just remove the wire clips from the old handle and attach them to the new one. put the screws back in and that's it! my repairman wanted $185.00 to do this. i came to partselect, read other posts on how to do it (ty guys) and did it myself for $21 bucks.

Easy fix, but the best of all was that I ordered the part on the evening and it was delivered by noon on the next day, I was very surprised, and it made everything easier.

To replace the part I used a power screw driver, because I had to open the inside of the door to get to the latch system, about 10 screws around the inside of the door.

I'm more confident about my dishwasher now that I know I can get any part for it this quick.

Thank you and Merry Christmas!

Purchased screwdriver head to fit dishwasher door screws. With the new screw driver removed all the screws from the door. Removed the broken door latch assembly.
Checked the voltage at the door latch assembly switches and switched off the dishwasher at the fuse box.
Had to break the old switches on the broken door latch assembly to remove the wire clips one at a time. Reconnected the switches on the new replacement assembly being careful to place the wire connectors on the new assembly as they were removed from the broken assembly. Placed the switch on the inside the door panel and installed all the screws. The only problem was removing the wire connectors from the broken door latch assembly that took a little time.

I removed the inside door cover. Pulled the 2 wires from the old unit and reinstalled them on the new one. As I removed the first wire, I placed it on the new unit....then removed the second one and installed it. I then replaced the latch assembly inside the door and reinstalled the inner door cover. It took longer to open the package and look at the new latch than it did to install it. I e-mailed PartSelect for the part on Christmas evening (Saturday) and had the new part delivered to my home by noon the following Tuesday.

Removed the upper spray supply manifold and the lower spray arm, and all other pieces to reach the chopper assembly, removing those pieces, installing the new pieces, and put everything back together. Success! The dishwasher is working as good as new.