Models > MDBH945AWW > Instructions

MDBH945AWW Maytag Dishwasher - Instructions

All installation instructions for MDBH945AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDBH945AWW
1-15 of 783
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken latch handle

  • Customer: Walter from Tucson AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 512 of 512 people found this instruction helpful
The hardest thing was figuring out that you only need to purchase the latch handle because it only comes as a complete latch assembly, why they even list the latch assembly as a separate part in the parts list stupid. (you get the handle and latch already put together and it cost less than the latch assembly without the handle). Anyway all you need to do is disconect the power from the dishwasher (unless you like to live dangerously like me) take your drill with the correct size torx bit and remove all the screws on the inside door pannel (the top center two screws actually hold the latch assembly in place). Disconect the 4 wires from the old part and reconect them to the new part and reinstall all the torx screws being careful not to strip the plastic threads that they screw into if you are using a drill. Whole process takes less than 5 minutes. I am surprised that Maytag used such a flimsy handle assembly in their dishwashers since they are supposed to have the repair men with the most time on their hands. They probably sell just as many handle assemblies as they do dishwashers that have this particular part in it, probably more since you will probably have to change it 2 or 3 times during the life of the unit.

Door release latch handle was broken. The handle was deeply recessed into the door and the door was difficult to open.

  • Customer: Dave from Livonia MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 469 of 467 people found this instruction helpful
Remove the 8 or 9 torx screws holding the inner and outer door assembly together (leave the bottom screws in), lift the old handle assembly out, transfer the switches to the new handle assembly, and reassemble door.

The utensil basket was old, bowed and the bottom was falling out.

  • Customer: Janet from Plano TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 383 of 387 people found this instruction helpful
I ordered a new replacement basket. The new one is a little different but it fits in the same place and takes up the same amount of room in the dishwasher. It looks very nice too.

door would not open

  • Customer: jeff from strongsville OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 374 of 375 people found this instruction helpful
remove torq scew from edge of inside of door and seperate plastic inner panel from out steel and then pull up on plastci unscrew 2 screw securing handle and reverse to assemble. Anyone can door this in under 10 mins.

2 broken wheels on basket

  • Customer: jeanne from waynesboro TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 362 of 364 people found this instruction helpful
unwrapped wheels ,pulled out drawer and easily put on new wheels...as we live way out in the boonies it was great to be able to order parts and have them delivered so fast...easy to fix....

Door handle broke but dishwasher still works

  • Customer: Wendy from W Melbourne FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 204 of 271 people found this instruction helpful
For probably a year I have been using my dishwasher with a broken handle. I would just pull the door out with a little bit of force to open it. Still I was concerned it would eventually break something else. After reading other people's experience with replacing it, it didn't sound like such a difficult repair and the part was less than 30 dollars counting shipping. Incidently, PartSelect ships fast so make sure you order the right part. I ordered the part Friday afternoon and got it the next day! And I didn't use overnight shipping. Sweet!
Here are the steps for repair.
1) Turned off power to dishwasher.
2) Removed all the screws on the inside of the door then shifted the panel over so I could get to the top.
3) The bottom of the latch assembly attaches to the control panel with two flimsy plastic notches and at the top with two of the screws that hold that back panel in place. (For me, I found that those flimsy notches had broken. I was concerned that I would have to buy a whole new control panel which was ~175.00 dollars. Yikes! Luckily the two screws at the top and the door panel behind it seem to be holding it in place.)
4) There are two pairs of metal prongs that plug into a white connectors on either side of the latch assembly. I had to use pliers to pinch the metal prongs together while wiggling the connector get it unplugged. This was the hardest part. (It would have been easier to just reuse the same metal plugs. Someone else did that and it seemed to work.) Be sure to note which side of the latch assemply the two connectors was plugged in to.
5) Plug the 2 white connectors to the new latch assembly.
6) Lay the latch assembly in place on the door.
7) Put the back panel down over it and screw it in place.
8) Turn on power.

Works perfectly!

Maytag makes a really crappy silverware basket. The bottom of ours fell apart the first year.

  • Customer: Kenneth from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 135 of 202 people found this instruction helpful
There was no repair to be done. Just replaced the defective basket with the new one.
I got the part two days after ordering it. Great service.

The bottom of our dishwasher's old utinsel basket broke out

  • Customer: Wade from Seattle WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 97 of 98 people found this instruction helpful
It was so easy to find the right part on the PartsSelect website. I just had to enter the manufacturer (Maytag) and model number and up popped skematics of all the parts available. I just clicked on the drawing of the basket and placed the order. It took less that 5 minutes. The part arrived 4 days later as promised. The repair took even less time than teh ordering. I simply took the old basket out and dropped in the new one.

I'm just happy to know there is a place that has such a user friendly website and stocks so many parts for older appliances. I had my house built in 1992 and several of the appliance are original. Fortunately I always keep the owners manuals for every piece of equipment so the model and serial numbers are readily available.

Door latch was broken -

  • Customer: John from Loveland OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 86 of 86 people found this instruction helpful
1.Turn of electric
2. Open dishwasher door
3. Remove scres for interior door cover
4. Lift and move the interior door cover to right
5. Use Pliers to pull off connectors of Latch
6. Use Pliers to attach replacement latch
7. Lay interior door cover back on door and line up with screw holes. Make sure you have the bottom lip over the bottom of exterior door by hinges. Bottom lip goes inside the dishwasher.
8. Put back in screws - not all the way and tighten snug (do not over tighen) once all are in place.
9. turn on power.
10. Done!

30 Minutes tops!

BROKEN WHEELS

  • Customer: Mary J. from Westwood MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 65 of 65 people found this instruction helpful
SNAPPED ON NEW WHEELS

The latch handle broke

  • Customer: Robert from East Hartford CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 96 of 158 people found this instruction helpful
Had this problem before and the part was simply a plastic latch which cost less than 5 dollars. That part has been discontinued and the latch is now the entire assembly. Although the part costs more, the repair is much simpler. Remove the screws from the inside of the door. Have to use hex nut screwdriver. Remove the panel and the assembly is right at the top. Unhook the assembly from the two (2) prongs. TURN OFF the electricity or touching the prong will bite you. Had to pry the latches off the prongs with a screwdriver as the fit is tight. Latch the new assembly on and rescrew the door panel and the job is done. Very easy and cheaper than a repairman coming out and charging $150.00

worn out silverware basket

  • Customer: Dayna from Logan UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 95 of 158 people found this instruction helpful
Ordered replacement basket online at much better price than available localy. When I recieved it discovered that it did not include the handle, but was suprised to see it labeled as "Genuine Maytag Parts" ( I realy expected a knock-off replacement part for the price difference). I was able to remove tha handle from the old basket and install it on the new one. Job done. No problem

dishwasher door leaks

  • Customer: jerry from vernon CT
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 56 of 60 people found this instruction helpful
I ordered and replaced both the door gasket (easy) and inner door seal (difficult) to try and correct a leak during operation. The door gasket was easily replaced. However, the inner door seal was a bit more trouble. After removing the inner door I found that the old inner seal needed to be removed and surfaces thoroughly cleaned of old build-up of dishwasher soap residue, in order to allow the sticky back tape side of door seal to properly stick to the door. There also was a plastic cover over the wire bundle that needed to be cleaned. The inner door seal was the exact length, so proper positioning of the sticky back was very important.
Upon reassemly the leak still existed and I was unable to correct the leak. Further inspection indicated that the basic tub/body of the dishwasher might be slightly distorted due to age and may not create seal with door seal as originally designed.
I guess I need to find a new dishwasher, at this point.
A word to the wise: Check to see if the tub/body is still in good condition.

Dishwasher not draining completely

  • Customer: Tim from Troy OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 51 of 53 people found this instruction helpful
You have to pull the dishwasher out from underneath the counter and set it on its side. Before removing, I used a shop vac to remove any standing water from inside the dishwasher. Once I pulled out the dishwasher, I then tilted the dishwasher forward to let remaining water fall on the floor, again, using the wet vac for clean up. After it is on its side, I used a socket wrench to remove the one bolt that holds the drain valve on. Then I used a socket wrench to loosen the clamp for the drain hose and removed the hose. You then need to turn the entire drain valve 1/4 of a turn counter-clockwise to remove the old drain valve. Once it is off, remove the bracket from the old drain and attach it to the new drain valve using a phillips screwdriver. Before I reassambled the drain valve, I used my wet vac to remove any debree from where the drain valve connects to the dishwasher. Reverse the prior steps to install new drain valve and install dishwasher back under the counter. I tested the unit before installing the dishwasher back under the counter to insure it fixed the problem. The hardest part about doing this, was actually taking the dishwasher out from under the counter, very easy process in general. One thing I couldn't figure out about my original problem of the water not completely draining out, is why would the drain valve start draining the water then after 20 seconds it would stop? I couldn't find the answer, so I assumed the drain valve is like a 2 stage system and took a chance on replacing the drain valve; it worked.

Maytag quiet series 300 stopped cleaning

  • Customer: mike from woodland hills CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 51 of 59 people found this instruction helpful
Remove the racks top and bottom. The Station D seals are at the far back on the tube that supplies water to the top and middle spray heads. Unsnap the old one and snap in the new - it only goes one way! This will repair the seal aroound the tube that supplies the middle sprayer and restore pressure to all 3 heads. Repalcing the screen accumulator is harder. you need a torx driver. remove the little thumb nut on the bottom sprayer and remove the sprayer. Then remove the tube where you just replaced the D station. (You of course could have done this earlier if you were doing both repairs) then 6 screws on the impeller housing. Now remove the 1 torx screw on the impeller and pull the impeller up and off. Remove the 3 screws on the cover and 2 screws on the accumulator. Clean all the old food scraps that are clogging up the works and reassemble in reverse order. Washer is working again!!
All Instructions for the MDBH945AWW
1-15 of 783