Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDB9750AWW

MDB9750AWW Maytag Dishwasher - Overview

Get Parts and Repair Help for MDB9750AWW

If you know the dishwasher repair part you need, you can browse the list of all parts on the MDB9750AWW, or you can search by name or part description. You can also find your part by where it is located on the MDB9750AWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for MDB9750AWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$30.68

Door Handle and Latch Assembly with Switches

This is a part found in your dishwasher. This part includes the black handle, latch, and 2 switches. This part is a simple on/off mechanism that prohibits the dishwasher from opera...

$7.33

Lower Wheel Assembly

This lower dishrack roller is less than two inches in diameter. It is made entirely of white plastic. If you find that your dishwasher is making loud noises or the lower rack is getting stuck when you are moving it in or out, it could be that the lower wheel assembly needs to be replaced. The dishrack wheels allow for easy movement of the dishrack in and out of the dishwasher. These rollers tend to wear down at the same speed, so it is recommended to replace both pairs at the same time. Open your dishwasher and remove the bottom rack, locate the locking tab, and rotate until it easily slides out of place. Slide the new wheel over the shaft and locate the locking tab to snap back into place.

$6.81

Upper Rack Wheel

Sold individually.

$30.29

Door Latch with Switches - NO Handle

This door latch, used in dishwashers, is located at the top of the door and locks the door shut when the dishwasher is working. If the door will not close or is damaged, changing the latch could be the solution. For this repair, remove all screws from the inner panel, then lift up the inner door panel and hold the door apart. Next, access the latch and pull wires from the switches. Refer to the manual provided by the manufacturer for further instructions and guidance. Remember to unplug the dishwasher from the power source or shut off the house circuit breaker before beginning this installation project.

$32.12

Silverware Basket - Split/Fit

This is now one complete basket instead of being sold in 2 halves.

$19.42

Docking Station with Flappers

If you notice that your dishwasher is leaking, or is not cleaning dishes properly, you may need to replace the docking station. The docking station is located on the water supply tube at the back of the appliance. It provides water to the upper and middle spray arm. This part comes with the accompanying flappers. This product is approximately 4 inches in length and 2 inches in width, and is made of white and gray plastic. To access the docking station, you will need to remove the upper rack. To do this, simply remove the end caps that keep the rack on the slides. Make sure to attach the flappers to the docking station before installing it in the dishwasher.

$2.96

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

$4.37

Fold Away Tine Pivot

$4.89

Door Cable Link

This is a part for your dishwasher. The door cable link helps to keep the door steady and give support to the weight of the door when it is being opened or closed. If you notice th...

$6.57

Dishrack Tine Pivot

This fold away tine pivot is almost four inches long. It is blue in color and is made of plastic.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken latch handle

  • Customer: Walter from Tucson, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 917 of 938 people found this instruction helpful
The hardest thing was figuring out that you only need to purchase the latch handle because it only comes as a complete latch assembly, why they even list the latch assembly as a separate part in the parts list stupid. (you get the handle and latch already put together and it cost less than the latch assembly without the handle). Anyway all you need to do is ... read more

Door release latch handle was broken. The handle was deeply recessed into the door and the door was difficult to open.

  • Customer: Dave from Livonia, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 516 of 518 people found this instruction helpful
Remove the 8 or 9 torx screws holding the inner and outer door assembly together (leave the bottom screws in), lift the old handle assembly out, transfer the switches to the new handle assembly, and reassemble door. read more

Replace wheel

  • Customer: Anthony from Greenwich, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 474 of 476 people found this instruction helpful
Tghe old one snaps off and the new one snaps right in . read more