Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDB9600AWQ

MDB9600AWQ Maytag Dishwasher - Overview

Get Parts and Repair Help for MDB9600AWQ

If you know the dishwasher repair part you need, you can browse the list of all parts on the MDB9600AWQ, or you can search by name or part description. You can also find your part by where it is located on the MDB9600AWQ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for MDB9600AWQ parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$7.33

Lower Wheel Assembly

This lower dishrack roller is less than two inches in diameter. It is made entirely of white plastic. If you find that your dishwasher is making loud noises or the lower rack is ge...

Order within the next 25 mins and your part ships today!
$30.29

Door Latch with Switches - NO Handle

This door latch, used in dishwashers, is located at the top of the door and locks the door shut when the dishwasher is working. If the door will not close or is damaged, changing the latch could be the solution. For this repair, remove all screws from the inner panel, then lift up the inner door panel and hold the door apart. Next, access the latch and pull wires from the switches. Refer to the manual provided by the manufacturer for further instructions and guidance. Remember to unplug the dishwasher from the power source or shut off the house circuit breaker before beginning this installation project.

Order within the next 25 mins and your part ships today!
$32.12

Silverware Basket - Split/Fit

This is now one complete basket instead of being sold in 2 halves.

Order within the next 25 mins and your part ships today!
$17.22

Inner Door Foam Insulation Strip

This genuine inner door foam insulation strip, sometimes known as bottom seal foam, is used to create a waterproof seal that helps prevent leaking from the door area of the dishwasher. The existing insulation strip may leave a sticky residue or leftover disintegrated strip that must be scraped off before installing the new strip. Residue can be scraped off with a putty knife. Be sure to remove all residue and clean surrounding areas of the dishwasher build. It is strongly recommended to check other sealant parts on the dishwasher door such as the door gasket and dispenser grommet to ensure the leaking issue is fully solved.

Order within the next 25 mins and your part ships today!
$4.48

Fold Away Tine Pivot

Order within the next 25 mins and your part ships today!
$19.75

Docking Station with Flappers

If you notice that your dishwasher is leaking, or is not cleaning dishes properly, you may need to replace the docking station. The docking station is located on the water supply tube at the back of the appliance. It provides water to the upper and middle spray arm. This part comes with the accompanying flappers. This product is approximately 4 inches in length and 2 inches in width, and is made of white and gray plastic. To access the docking station, you will need to remove the upper rack. To do this, simply remove the end caps that keep the rack on the slides. Make sure to attach the flappers to the docking station before installing it in the dishwasher.

Order within the next 25 mins and your part ships today!
$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

Order within the next 25 mins and your part ships today!
$6.57

Dishrack Tine Pivot

This fold away tine pivot is almost four inches long. It is blue in color and is made of plastic.

Order within the next 25 mins and your part ships today!
$47.70

Rack Adjuster with Wheels- Right Side

This adjuster connects to the right hand side of the top dishrack. It is used to change the height of the upper rack.

Order within the next 25 mins and your part ships today!
$47.88

Rack Adjuster with Wheels - Left Side

This adjuster connects to the left side of the top dishrack. It is used to change the height of the upper rack.

Order within the next 25 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

2 broken wheels on basket

  • Customer: jeanne from waynesboro, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 367 of 370 people found this instruction helpful
unwrapped wheels ,pulled out drawer and easily put on new wheels...as we live way out in the boonies it was great to be able to order parts and have them delivered so fast...easy to fix.... read more

Broken door operating handle (unit broke at the hinge)

  • Customer: Richard from Bridgewater, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 169 of 179 people found this instruction helpful
First - Make sure electricity to the dishwasher is turned off. Very important for there are exposed electrical connectors in the location where you will be making the repair. Second - removed the inner door liner. Removal is by unscrewing the tork screws around the perimeter of the assembly (when you take this inner door liner/cover be careful because the d... read more

One of two plastic rollers on this metal part broke (twice)

  • Customer: Jim from Hendersonville, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 111 of 111 people found this instruction helpful
Remove the entire top dish rack by removing the two front covers on the left and right metal grooved slides. The covers are plastic. No tools are required. After removing the top dish rack, the rack adjuster (with two cheap plastic wheels) is easily removed with an allen wrench. There are six fasteners that must be removed to detach the rack adjuster... read more