MDB9100AWA Maytag Dishwasher - Instructions

I ordered and replaced both the door gasket (easy) and inner door seal (difficult) to try and correct a leak during operation. The door gasket was easily replaced. However, the inner door seal was a bit more trouble. After removing the inner door I found that the old inner seal needed to be removed and surfaces thoroughly cleaned of old build-up of dishwasher soap residue, in order to allow the sticky back tape side of door seal to properly stick to the door. There also was a plastic cover over the wire bundle that needed to be cleaned. The inner door seal was the exact length, so proper positioning of the sticky back was very important.
Upon reassemly the leak still existed and I was unable to correct the leak. Further inspection indicated that the basic tub/body of the dishwasher might be slightly distorted due to age and may not create seal with door seal as originally designed.
I guess I need to find a new dishwasher, at this point.
A word to the wise: Check to see if the tub/body is still in good condition.

I pulled the interior of the door until I was able to get to the switches on the door latch. I determined at least one switch was completely worn while the other worked minimally. I then looked for the latch assembly and found out that it was no longer available. So I did some searching and found the exact switches I needed from PartSelect. The switches came in about 3 days which then I installed them. The dishwasher powered right up and stayed on. So in the end it was much cheaper to repair this unit than buy a new one right now. Plus, my wife is happy and so am I. Thanks PartSelect for carrying the parts I needed.

The initial repair was more involved due to figuring out how to get at the problem. A foam sealer strip located at the bottom of the inner door had lost it's seal. I first sent off for one and it was of relatively thin material. It was carefully installed but still leaked. I ordered another one from Part Select and it had thicker foam. It was installed right over the previously installed strip and made a tight seal. (knock on wood)

It was initially unclear precisely which part I needed. I called PartSelect customer service and the agent was extremely helpful and able to quickly advise me on the correct part.

Installation was straight forwared. I used a torx screw-driver to remove the screws holding the inside-door planel. There are wires attached so this needs to be done with care.

I then removed a thin plastic film cover the control assembly. The control assembly is held firm by a screw and is also "snapped" in place. There are obvious tabs which can be spread to allow the assembly to be lifted out.

Each of the wire harness can then be removed from the control assembly.

With the new control assembly in place, the wires can be reconnected very easily. The assembly board itself is well marked enough to determine where each of the wires connects but really, the connectors for each harness is unique so pretty difficult to not get right.

Replace the plastic film and door cover and you are back in business.

I had previously gotten a quote from Sears to do this work and it was over $200 works of labor. Go through PartSelect I not only saved about $40 dollars on the part itself, I also saved $200 on a fairly easy repair that I could do myself in under 30 minutes.

The real cause of the leak had nothing to do with the foam strip. The latch for the front loading door at the top needed to be adjusted to hold the door in tighter to the rubber door seal. This simple adjustment stopped the leak but since the foam seal was all encrusted with dried detergent from probably years of absorbing the leak, I replaced it with your new foam strip. I used a screw driver with torx bit and removed the stainless screws holding the inner door to the outer door. Once these were separated I removed the old foam strip using a putty knife and lacquer thinner. Placing the new strip onto these cleaned surfaces was the easiest part of the whole repair.

The replacement of the spring linkage was simple - the pulling out and pushing in of the under-the-counter dishwasher was the difficult and time-consuming part. The repair of the part took less than a minute.

The actual repair -
1. Hook the linkage to the dishwasher door
2. Hook the spring to the dishwasher base
3. Hook the spring to the linkage.

Getting the dishwasher out to be able to make the repair involved:
1. Unscrewing the base panel (6 screws had to be removed)
2. Unscrewing the dishwasher from the counter (two screws)
3. Turning off the water supply
4. Disconnecting the inline water supply from the dishwasher.

Once the part was replaced, I had to return the dishwasher to its original position, which meant performing the four steps (in reverse) used to pull out the dishwasher.

First replaced rubber seal around door, which did not stop the leaking.
Then ordered insulation foam strip and replaced old one, which fixed problem. Put new strip over the old one because tub was slightly warped.
Very pleased with order speed and cost.

After replacing the door gasket and seeing that this wasn't the problem, using the schematics found at partselect.com I finally realized that it may be the insulation foam strip. I ordered the product and received it very quickly. Installation went fairly quickly. It was easy to remove the old foam strip and install the new one. The only problem was that the foam strip was about 1/4 " too short and it didn't cover the entire bottom. I improvised a little bit and cut off some of the old strip and covered the gap. So far the leak seems to have been fixed. In addition to the foam strip I had to buy a torx screwdriver for $11 at the local hardware store. The total spent was around $25.

First I unplugged the dishwasher since I was working on the electrical. I just unscrewed all the screws on the inside of the door till I could get down to the door latch. I found that a tiny piece of plastic had broken off of the white bracket that holds the electrical switches (these turn it on when the door latches and off when the door opens). I had to break several tiny plastic prongs off the old bracket in order to pull the switches out of it (gently so the wires wouldn't pull out of the switches) and the door handle latch fell out easily. Then it was easy to snap the switches back into the new bracket, and slip the handle latch back in, and screw everything back down. It worked! I've never worked on a dishwasher before but looking at the photos of all the various parts (even the ones I didn't need to use) really helped me to see how the things go together and to narrow it down to which part I would need. The dishwasher was totally un-usable and all I spent to make it run again was less than $5. Thanks to Partselect!

After examining the door and main seal around the dishwasher I thought everything looked okay. I looked online to order a new seal anyway and discovered from others that the leak was probably the insulation strip inside the door rather than the seal around the dishwasher. I ordered an insulation strip and it arrived a couple days later. I removed the seven screws of the interior door cover and disconnected the electrical. After removing the old insulation strip and installig the new one I reconnected the electrical wiring/plugs, put the door cover back on, and reinstalled the screws. Total time was about 15-20 minutes and the leak stopped. It was very easy and saved the cost of a repairman or a new dishwasher. I'm very glad that I "listened" to others and went with the new insulation strip.

Peeled off the old foam strip, cleaned with rubbing alcohol, let dry completely, applied new foam strip,replaced door interior done I wish repairing relationships with fiance and kids were one tenth this easy.

First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.

Removed four screws on bottom plate. Located repair site on outside of cabinet. Had to hook spring on bottom rear plate by brail. Then attached linkage to spring and ran stiff wire through linkage to raise it above arm. Called a man with stronger but larger hands had him stretch the spring while I guided linkage over arm and into the slot using the wire. Removed stiff wire with needle nose pliers and reassembled front plate.

Ordered the spring and the Door Spring Linkage. Turned out to be a broken Door Spring Linkage not the spring. Unscrewed the two screws securing the dishwasher to the countertop and slightly pulled out the dishwasher enough to see the spring. Replaced the broken Door spring linkage and it resolved the issue.

1) Emptied Dishwasher (roll-around model)
2) Tipped it onto its back
3) Removed Toe Kick (2 screws) and Bottom Cover (4 screws) (screw driver)
4) Opened Door to access side panel (careful not to let it drop on my fingers)
5) Using Torx driver, removed two screws holding side panel on. This makes it easier to access the linkage and spring.
6) Removed broken link
7) Installed new link and spring noting the spring direction from the spring on the other side of the door.
8) Pulled spring over the bottom rail bracket with pliers.
9) Reinstalled panels in the reverse order.