Models > MDB7600AWW > Instructions

MDB7600AWW Maytag Dishwasher - Instructions

All installation instructions for MDB7600AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB7600AWW
886-900 of 927
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishwasher left residual water at end of cycle.

  • Customer: Mark from Brecksville OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Very straight forward repair. Parts Select provided the right part with very timely (regular FedEx)delivery. Repairclinic.com provided excellent video to show basic repair steps. Suggest using a "star" tip screw driver to disassemble interior parts of the machine to clean out years of gunk which will reduce the chance that the drive motor will bind/fail (which mine did and which saved me the cost of a new motor or new dishwasher). Upon reassembly, be sure to check water supply copper compression fittings for leaks that moving the machine can cause. Place pads under "feet" of machine to avoid marring wood floor when moving machine.

impeller in pump was broken

  • Customer: Jaynee from American Falls ID
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
changed impellers and it went really smooth only thing we forgot to hook waterline back and had a pool in kitchen how fun to clean

dishes were not being cleaned

  • Customer: William from Littleton NH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
followed video instructions online.

Top washer arm clip broken

  • Customer: Christopher from Elgin SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Used flat blade screw driver to unclip the holding bracket. Snaped new bracket and wash arm on. Took all of about 30 seconds.

Plastic wash arm broke and wouldn't snap back in hole at top of dishwasher

  • Customer: Teresa from St. Charles MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Aligned the hole and the appropriate part of the wash arm and snapped them back in. Thanks.

DW leaving dirt in bottom of glasses

  • Customer: suzanne from Church Hill TN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The original problem that brought me to Parts select was a broken wheel on the top tray. While searching for part #s I came across several descriptions of dishes not clean . The videos available on line here were very detailed. This encouraged me to go ahead and order the parts. They arrived soon and were accurate to my order. The video on replacing the seal and chopper walked me through the entire job very clearly. Going slow and carefully keeping track of al screws I replaced the chopper, impeller and the filter. The filter did have a tear in the screening which allowed dirty water back up into the dishwasher.

Dishes were not getting clean

  • Customer: Michael from Buttw MT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Thank You PartSelect for making this repair project simple and stress free. The exploded diagram of the appliance was clear and consise. The parts list was very helpfull. Showing me which parts were the most replaced gave me the confidence to order, reducing the prospect of having to return items ( always a pain point ). Parts arrived in just a few days. Followed the instructions on the video. Dishwasher was back in operation in no time and passed an overly thourgh dish inspection. Your site is amazing and is on my favorites tool bar. Thanks Agian !!!

dishes weren't getting clean

  • Customer: Reno from Lake Montezuma AZ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
followed directions (boring, I know, but it works) on the accompanying video. simple

The glasses on the top rack had food particles in them after a wash cycle

  • Customer: David from ocala FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I initially took everything out and cleaned everything with the shop vac, and outside with the garden hose. That did not work, so I looked on parts select for a new accumulator filter, as I was not able to clean that very well. To install the new filter, I removed the sliding racks, top and bottom, and the water manifold, then removed the lower wash arm, then the parts under that, the filter plate, the outlet, the impeller, all the way to the accumulator filter. After removing that, installation was the reverse. I also cleaned the middle washing arm, and the lower, as I noticed food particles blocking the outer holes. All is good now, and the dishwasher, which we use almost every day, is working fine.

Dishwasher did not clean and drain properly

  • Customer: Noel from Orange TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Routine repair. There are videos on the net that show exactly how to replace the filter unit. However, when you order the filter, order a replacement pump impeller. The impeller must be removed to remove the filter on this model. The impeller was stuck on the shaft, and I had to destroy it with the side cutter pliers to get it off. Before putting the new one on, clean the pump shaft thoroughly and lube the shaft with silicon lube or Vaseline jelly. Clean the bottom of the water pan thoroughly, then reassemble. Then pour one cup of vinegar in the bottom of the dishwasher and run it with no dishes. This will clean the inside of the dishwasher.

Dishes not getting clean

  • Customer: Lesley from Saint Louis MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We recently purchased a new home and it didn't matter how hot we ran the water in the sink before starting the dishwasher, the dishes, especially glasses, were filthy. Extra rinse cycles, pots and pans cycle, nothing worked. After finding this site, we took the chance on what the troubleshooter recommended and bought the accumulator filter and wash impeller. The parts came so fast! We followed the videos on this site step by step and we were successfully able to replace the filter and impeller. The impeller was COATED in nasty slimy grossness; it was obvious the previous owners never rinsed their dishes before running the dishwasher. After replacing these two parts, we have clean dishes! We have switched from tablets to liquid detergent which also helped (not sure why, tablets have worked at our old house just fine).

Dishes and glasses were left with little specks of food on them.

  • Customer: Vaughn from Great Falls VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We watched the very excellent video on this web site for replacing the Accumulator Filter and followed the instructions it provided. It's possible that we could have just cleaned our existing accumulator filter once we understood what it was and how to get to it, but the results of replacing it have been dramatic. It's like a new dishwasher.

Food chopper was broken.

  • Customer: Bob from Souderton PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Followed video. Everything went together fine, but leaked water around motor shaft seal. Read comments section on video and someone had the same problem. I had pushed the seal into base too deep. I pulled it out and reseated it. It worked without leaking after that. Bob

Water leak right front

  • Customer: Mark from Tallahassee FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Simply removed switch and float a d replaced them. A real no brainer!

Leaking and water level

  • Customer: Ferrellin from Gleason TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Lifted Float out....Located Float switch ...replaced
All Instructions for the MDB7600AWW
886-900 of 927