Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDB7600AWW > Instructions

MDB7600AWW Maytag Dishwasher - Instructions

All installation instructions for MDB7600AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB7600AWW
61-75 of 935
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The regular wash button and the start button would not light up.

  • Customer: Todd from Waterloo, NE
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 11 of 15 people found this instruction helpful
Just had to remove the screws from the inside of the washer. Took the screws off of the control panel. Disconected the wires (easy) then replaced with the new part. Much easier than I thought it would be, I might be thinking of doing repairs for other people now... thank you so much

Dishwasher heating element bad

  • Customer: Gary from Indianapolis, IN
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 10 of 12 people found this instruction helpful
I could not reach the heater element nuts from under the dishwasher so had to pull out the dishwasher. I removed the screws around the front of the dishwasher and pulled it about half way out before the water inlet pipe and the electrical wires stopped me. I shut off the water, unhooked the copper pipe, and unhooked the electrical wires (shut off circuit breaker first). Pulled the dishwaser out so I could remove the element nuts and wires to the element. Removed the old element and installed the new one - the old nuts would not fit. I went to a local appliance parts store and found that my element is no longer made. I had the correct replacement element but you need to order the nuts also. Luckily, the local store had a small brass nut that worked. Reattached the electrical wires to the element, pushed the dishwasher half way in, reattached the water inlet and electrical wires, pushed the dishwasher all the way in and scewed back into the cabinets. All is well now and the dishwasher is working much better.

Very little water going into the dishwasher

  • Customer: Ralph from Taft, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable), Wrench set
  • 11 of 15 people found this instruction helpful
Unpluged the electric, Disconnected the water line and the drain line. Removed the dishwasher. Removed and installed the new water inlet valve and the float switch. This was a very simple repair. Reinstalled the dishwasher and connect
the water and drain line. Pluged in the power line. Turned the dishwasher on and it worked perfect. Thank you for the correct parts.

Upper Dish / Glass Tine

  • Customer: James from Wolcott, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 21 people found this instruction helpful
Upper dish rack with dish / glass fold away tine has two broken latches, this situation is causing instability. Went to partselect for schematic and found what looked like the necessary replacement latch/s on print and ordered all latches. Received parts only to find they were the wrong ones. Evidently they are the parts for the bottom dish / glass fold away tine. Removed upper tine and still looking for the actual replacement parts on the schematic with no luck.

The plastic piece that held the rack to the side of the slider broke

  • Customer: Sally from Mission Viejo, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 10 people found this instruction helpful
First I removed the screws and disasempled the plastic covering that held the slide in place. I then replaced the rack adjuster and replaced the screws.

This was exciting for me as I was not about to wait for my husband to do it as I had a load of dishes in the sink just waiting for it to be done!

It was amazingly simple and the hardest part was remembering where in the rack it was to be replaced! I was back in commission within 15 minutes (It would have been 10 if I had placed it right the first time!!

the soap dispenser wouldn't open during cycle

  • Customer: paul from spring hill, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 9 of 10 people found this instruction helpful
I unscrewed the door panel. removed the plastic cover protecting the dispenser. unscrewed the dispenser (6 screws). I removed the old dispenser and put the new one on and put it all back together. It was pretty easy.

Upper Rack not Cleaning

  • Customer: Stephen J from Sammamish, WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 8 people found this instruction helpful
First I read all the reports for not cleaning properly already listed on this site. I had to replace the docking station with flappers. When I removed the station I lost the flappers down the water delivery tube just like Jon said I would in his repair post so I removed the water distribution assembly fished out the old flappers and snapped in the new.
But then I figured I might as well check out the accumulator while I was in the tub anyway - I had read that you need Torx screwdriver bit, which I had, undid the screws, pulled out the accumulator screen which was about 80% clogged, discovered I need a new chopper blade and my impeller is disintegrating, put it back together and lost ten minutes looking for the three screws I had incorrectly put in too soon, and now it is cleaning a packed full load like it was supposed to do.
**I love this site - I went to the virtual repairman and it listed every problem I had with this appliance in the order they happened (door latch broke years ago). - I think I am going to look up stuff that I own so I will know ahead what could go wrong with them.

And absolutely NO DUCT TAPE was used in this repair.

Detached Water Distribution Manifold

  • Customer: Harry from Bensalem, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 17 people found this instruction helpful
The original brackets that hold the water distribution manifold to the back and top of the tub came off the "X-shaped" plastic posts on the tub walls. That caused the upper wash arm to sag down into the travel of the upper dish rack and was broken off when the rack was pushed in.
I bought 2 new brackets and a new wash arm. The new brackets had a smaller aperature than the originals and fit tightly onto the plastic posts, holding the manifold firmly in its proper location. Replacement of the brackets and the new wash arm took less than ten minutes and required no tools!

Small / slow leak at bottom corner of dishwasher door.

  • Customer: Adam from Acworth, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
After examining the door and main seal around the dishwasher I thought everything looked okay. I looked online to order a new seal anyway and discovered from others that the leak was probably the insulation strip inside the door rather than the seal around the dishwasher. I ordered an insulation strip and it arrived a couple days later. I removed the seven screws of the interior door cover and disconnected the electrical. After removing the old insulation strip and installig the new one I reconnected the electrical wiring/plugs, put the door cover back on, and reinstalled the screws. Total time was about 15-20 minutes and the leak stopped. It was very easy and saved the cost of a repairman or a new dishwasher. I'm very glad that I "listened" to others and went with the new insulation strip.

Drain pump noisy

  • Customer: Scott from High Point, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
As others have described once you slide the dishwasher out and tilt it for access you simply remove the discharge (use something to catch the water), torx screw that secures the bracket to the unit, and twist counter clockwise until the pump is free from the drain tub. Reassemble in reverse order

ribbon cable for control panel had two conductors broken. requires the replacement of the control panel.

  • Customer: Pedro from Jacksonville, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
1. De-energize appliance at your electrical circuit breaker panel.
2. using torx # 15 remove the back cover of the door. Careful not to pull on wiring between door and cover.
3. Remove the cover to the circuit board to access the control panel "ribbon"
4. carefully and gently pry the plastic tab which secures the ribbon to the circuit board. The ribbon will be released and then remove the control panel two mounting screws on either side.
5. Don't worry, this takes longer to read than to perform the required steps.
6.Now install the new panel, do not tighten the screws until you have all the screws in just snug.
place the ribbon connector into the slot at the circuit board, secure it with the tab by pressing gently until its secured.
7. Completely tighten all control panel and circuit board cover screws, place back cover and ensure that the bottom end goes over the edge of door, careful with those foam splash seal and align all screw holes, replace screws, again do not tighten until all screws are in place.
8. Turn appliance circuit breaker back on and see that the LED lights come on on the control panel. Run a test load and enjoy the feeling of a job well done.

Motor would not turn the impeller, no wash pressure.

  • Customer: mark from blackwood, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 7 of 7 people found this instruction helpful
Not a bad repair once you diagnose the problem. Took me three tries to figure it out. Just make sure you follow the instructions. I used an allen wrench to hold the motor in place while tightening the part onto the motor shaft, this way I didn't have to remove and flip the dishwasher to do the repair. The good news is the replacement part I needed was metal instead of plastic, thus I should never have this problem again. I don't understand why it was plastic in the first place but all of my appliance problems seem to be made to fail after several years of service.
Repair was

Would not run the full 2 hour cycle also diffcult to get the dishwasher to turn on

  • Customer: William from Northridge, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 8 of 10 people found this instruction helpful
First removed the inside door panel which exposed the box that contained the control board. Removed the old control board and replaced it with the new part making sure that the connectors will connecte to the correct place. With the back panel removed I also replaced the latch assembly. Was a very simple job and the dishwasher is working great. Thanks to PartSelect for having the diagram of the dishwasher that help to locate correct parts.

Door latch on the dishwasher broke.

  • Customer: Christopher from Porter, IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
First I opened the breaker on the dishwasher removing power from the unit. Then I removed the Torx head screws on the cover on the back side of the front door. Then I pulled off the stainless steel sheet metal panel which exposed the door latch. Then I unplugged the electrical connectors to the two micro switches on the assembly, next I plugged in the connectors on the new latch assembly and postioned the latch back on the mounting holes. Replaced the stainless steel sheet metal and put the screws back.

Wife broke the knob

  • Customer: Fredy from Fullerton, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
Best part, i go this thing on my hands right of way..Great place, great price...Highly recommende
All Instructions for the MDB7600AWW
61-75 of 935