MDB7600AWW Maytag Dishwasher - Instructions

took the bottom spray arm & lower plastic pieces out, unscrewed the impeller & replaced it. the original impeller which holds the disposal blade down & wore down & no longer retained the blade. snap.

Once I got the door open, I removed the door cover screws with a Torx driver, where I found the broken handle and the Latch Assembly. One of the plastic handle pivot points had broken clean off. In my Brilliance, I went online to PartSelect, found that the part that I needed had been discontinued (from Maytag) and picked one that looked right. It ended up being the assembly without the handle, the part I needed. Save yourself some time and call the 800 number to make sure you get what you need. They were very helpfull in returning the wrong part to get the right one. Once I had the part, the repair was very straightforward. I just had to open the door up again, swap in the new Latch Assembly with the steel reinforced pivot point handle, and put the screws back in the door. The latch assembly is held in place by two of the door screws. Watch the cut off switches on the assembly, the power is hot until you power off the circut at the electric panel.

Simply popped the new cover in. My part by the way was really easy to identify on the website, easy to order and arrived in a very timley fashion!

We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.

I removed the lower wash arm held by a single center plastic coated nut with pliers.

I then removed the six pump housing screws and the three filter cover screws.

This allows access to the pump impeller which is held by one screw. Once it is removed the filter plate, chopper and motor seal can be removed.

I actually had done this before to find a noise. At the time I noticed the impeller had become shorter due to plastic breaking off the impeller. It still fit the motor shaft so I just cleaned out the plastic and screwed it back on. I did not check for water leakage until I noticed loose flooring material a couple weeks later.

This is the mistake I made. The impeller is made so it presses down upon the motor shaft seal expanding it to seal out water. Because the impeller was missing the lower skirt it was too short to but enough pressure upon the seal to stop leakage.
Never use a impeller which is damaged in any way.

Due to this error I have had to buy a motor assy also. It was destroyed by the water.

Being a fairly technical female, I decided after Internet research to replace this part by myself. It could not have been easier - even after reading several Internet horror stories. I believe the major difference being I replaced the entire assembly, not simply the latch.

You need a hex-head allen wrench to remove the inside cover of the dishwasher door, and some sort of pliers to remove the old unit. I used vice grips since I am a wimpy girl - they worked nicely (this took the longest time).

Step by Step:

Turn off the power to your dishwasher.

Remove the door screws and carefully lift it to access the door latch assembly.

Remove the old door latch by unplugging the black and white electrical mechanism. Pay close attention to which side the black and white connections are removed from for reconnection reasons. This is where I had to use vice grips. It took a bit to "unplug" the old latch assembly.

Once the old latch assembly is removed, position the new latch assembly and reconnect the electrical source.

Carefully reposition the door and replace the screws.

Turn on the power.

Run a short cycle (I used rinse) to make sure that the unit was replaced correctly.

Can it be any easier than that??

First of all I shut the power off to the dishwasher at the breaker box. Turn the water off to the dishwasher. Unhook the water line and then remove the screws that go around the outside trim edge of the dihwasher that secures it to the cabinets. Then you will want to look at the adjustable legs on the dishwasher. You may need to lower the legs to get the dishwasher out from underneath the counter top. While you are doing this you should also pay attention to your drain hose. My drain hose had plenty of slack so I was able to pull my dishwasher out from underneath the cabinet and then unhook it. You should have towels or a bucket in place to catch any water that is inside the drain hose. Next I laid the dishwasher over on its left side and I was able to access the pump. I then used a flat screw driver to remove the hose clamp and remov the drain hose from the pump. I then unplugged 1 wire connector and a bracket and could turn the pump counter clockwise and removed it from the dishwasher. There is a bracket that must be removed from the old pump to the new pump. Once this is accomplished You are ready to reinstall the new pump. I took a towel and wiped the area where the pump hooks into the dishwasher to make sure all debris was removed. I then used a very small amount of gasket sealer and placed it around the "O" Ring on the new pump. Next place the pump back in the whole and turn in a clock wise direction securing it back into the dishwasher. Hook up the drain hose and the wire connector. Make sure the bracket is postioned properly and you are ready to put dishwasher back under the counter.

The real cause of the leak had nothing to do with the foam strip. The latch for the front loading door at the top needed to be adjusted to hold the door in tighter to the rubber door seal. This simple adjustment stopped the leak but since the foam seal was all encrusted with dried detergent from probably years of absorbing the leak, I replaced it with your new foam strip. I used a screw driver with torx bit and removed the stainless screws holding the inner door to the outer door. Once these were separated I removed the old foam strip using a putty knife and lacquer thinner. Placing the new strip onto these cleaned surfaces was the easiest part of the whole repair.

The first thing I did was read the all of repair stories that others had submitted. Then I set the timer and chucked up the Torx bit in my electric drill/screwdriver. There are 10 Torx screws on the inside of the dishwasher door and they came out very quickly. The top two screws hold the latch in place. I lifted the inside stainless steel cover to get acces to the latch. There was enough slack in the wire that I was able to remove the latch from where it was and extend it above the door. This let me lay the stainless steel liner back onto the inside of the door without removing or disconnecting the soap dispenser. Thus exposed, disconnecting the connectors from the old latch and reconnecting them to the microswitches on the new latch was a breeze. Once connected, I reinstalled the latch assembly, repositioned the liner correctly and replaced the ten screws. The entire job, including putting my tools away and cleaning up took eight minutes. I did it on my lunch break. The eight minutes included pulling the circuit breaker and reconnecting it (very important, that step). The new latch/handle assembly completely fixed the problem.

This is a very common problem with this model. However, in addition to this part, you also need the following part numbers (which are not listed for this model):
PS920544 - Lever Adjuster
PS893981 - Cover, Rack Adjuster

The updated RACK ADJUSTER ASSY part did not match up to the other parts in my dishwasher. But, after I found a diagram for another dishwasher model that showed the above two parts as well, I ordered them in hopes that they would work for mine. They worked like a charm, and the design of the new updated part is much better than the original part (which, if you take a look at epinions.com, breaks on just about every machine).

I hope this helps someone out ... I was close to ditching our 1.5 year old dishwasher and buying a new one!

-Remove all torx screws on door (2 min).
-unplug switch's (10 min) I used a small curved awl for this, there is a small nub that goes into the connector that needs popped off to release. I got the first switch in a few seconds, the second took several minutes.
-plugged in new switches and replaced torx screws (2 min.)
-another job well done.
The pictures on the web site were not accurate. I thought i needed the Latch assembly and the latch assymbly (Bisque)M. The Latch assembly Bisque had everything that the Latch assembly had plus the handle (and it cost like $8 less. So I had to return the Latch Assembly. Hopefully I made that clear I saw similar info when I was making my purchase but it was not clear so I ended up ordering more than what I needed.

After looking the situation over, I decided to remove the entire lower rack and place it on the counter where I could see better. I specified I needed the front tine (part # 24), but received both front and back tines). I used the screwdriver to help slip the old piece out of the plastic clamp end. I broke the end of the first clamp, but fortunately, replacement clamps were also included in the kit. I decided it would be easier to assemble the tines and the clamps first, and then install that into the rack, so I had to remove the other plastic clamp and did so successfully. Then holding the assemblage in place to see just where to snap it into place, I proceeded one clamp at a time and installed it. I kept the new back tine guide just in case someday that one wears out too.

Turned off water and power to the unit. Removed kick plate from under the dishwasher to access the water contol valve. Placed an absorbant rag under the water valve and water line. Disconnected solenoid on water control valve from electrical connection with my fingers. Used a standard adjustable wrench to disconnect the water line from the water control valve. Then used a 1/4" nut driver to loosen the two bolts that hold the water control valve on to the mounting bracket. Pulled the water control valve slightly forward to disconnect the water feed line to the dishwasher. Used a blunt end plier to pinch the clamp open and slowly wiggle the feed line off of the water control valve. Then removed 90 degree elbow off of the water control valve and used pipe dope and connected the elbow onto the new water control valve. Replaced water control valve in reverse order and utilized new hose clamp to reconnect feed line to new water control valve. Saved door seal for future use, when seal goes bad.

I was able to remove the old handle and place it on the new basket - using only a screw driver.

Upper dish rack with dish / glass fold away tine has two broken latches, this situation is causing instability. Went to partselect for schematic and found what looked like the necessary replacement latch/s on print and ordered all latches. Received parts only to find they were the wrong ones. Evidently they are the parts for the bottom dish / glass fold away tine. Removed upper tine and still looking for the actual replacement parts on the schematic with no luck.