Models > MDB7600AWS > Instructions

MDB7600AWS Maytag Dishwasher - Instructions

All installation instructions for MDB7600AWS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB7600AWS
91-105 of 1,090
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Leaks out and below the front door

  • Customer: John Todd from Franklin WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 9 people found this instruction helpful
First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.

A wheel on the upper tray that moves in the slide broke.

  • Customer: Melvin from Rochester Hills MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Actual repair took less than 5 minutes. Removed 5 screws from original "adjuster' and removed the outside housing. Aligned the replacement part and simply replaced the five screws. Wheels on the replacement part are held in place with steel "rivets" while original wheels are all plastic and held in place with a screw . The replacement part is a much sturdier set-up. I saved the unbroken wheel from the original adjuster in the event a wheel on the right hand adjuster breaks.

constant crud on glasses

  • Customer: Janice from Parker CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 8 of 15 people found this instruction helpful
Accumulator was as easy as just removing srews and replacing the part. The Float I broke by accident and was more complicated to replace required 2 people to manage parts.
Dishes finally coming out clean!

Dishwasher filled normally with water and seemed to be cycling normally, but after cycle complete, no washing had occurred.

  • Customer: Kenneth from Brandon MS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
I first listened carefully and noticed that during cycling, the electric motors could be heard starting, stopping, and apparently running normally during both wash and emptying cycles. However, no water was being pumped around during the wash cycles, while emptying (which uses a different motor) worked normally throughout all cycles. Thus it seemed to me that the electronic programming was working correctly in turning both motors on and off as necessary. So I figured somehow the wash motor impella was not turning and pumping water, despite the fact that the motor was indeed running correctly. So I removed all the plastic housings, the screwed on impella, and the metal chopper at the base of dishwasher. Then I was able to easily pry the old plastic chopper sleeve right off of the electric motor shaft (normally it is screwed on and cannot be pryed off). Since the plastic threads inside the chopper sleeve were completely stripped, the motor shaft would turn but the impella would slip on the shaft and not be driven. The replacement sleeve was much better constructed (metal not plastic). It could be easily screwed on to the motor's driveshaft after lifting the old rubber seal and gently holding the motor shaft with a pliers (carefull to avoid scratching the shaft). I removed the old rubber seal nd replaced it with the new one from the kit, right over the newly installed metal chopper sleeve. Next, I easily centered the metal chopper sleeve and pressed in the new seal after reinstalling the plastic/metal chopper screen, using the temporary jig included in the kit. Then the jig was discarded and the impella simply screwed onto the chopper sleeve (using the appropriately threaded hold-down screw provided in the kit). Finally, the rest of the plastic hardware is screwed in place. Waahhlaa...now impella is motor driven again and blows water hard into the dishwasher during the wash and rinse cycles. Total cost of job to do-it-yourself, $29.50 including shipping (which only took three working days). Estimated job if down by appliance repairman, $140 (assuming the repairman didn't first erroneously blame the problem on faulty electronics then charge you hundreds of $$'s to replace circuits which were not broken to begin with, only to find the dishwasher still not washing/rinsing after his expensive electronic circuit replacements. The actually mechanical fix was cheap and simple. Truthfully, there is no excuse for Jenn Aire to ever use a plastic Chopper Sleeve in their dishwashers to begin with.......carefully planned obsolesence if you ask me. Oh well, it works perfect now. I doubt if even the four marbles my 4 year old had tried earlier to wash in my dishwasher (stripping out the original chopper sleeve) would do any damage to the metal replacement. However, I don't plan on testing my hunch. A simple fix, but a slightly challenging diagnosis which relied on a keen sense of hearing and a quiet workplace. Seems many people in these blogs have had the very same problem with their Jenn Air/Maytag dishwashers, and have made the same diagnosis and the same simple fix. Thank you mucho, PartSelect.

original basket fell apart

  • Customer: D from Villas NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

Replaced old black with new ss door panel

  • Customer: Patricia from Saint Louis MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
Difficulty was primarily because there were no instructions for the procedure so trial and error. I suggest: 1) Turn off power circut to the dishwasher. Then remove the star headed screws on the panel with door open and this separates the interior plastic door liner from the exterior door panel 2) remove the 4 screws inside the door that are the final fasteners for the exterior panel and the metal brace 3) bottom of the old door panel is curled and needs to be bent back slightly at the bottom 2 corners with a screw driver or pliers so the old panel can be removed by sliding the panel upward past corner brace while being careful with the electrical connections 4) once the old panel is removed the new one can be slid down the door arms and the interior screws attached 5) finally install the star head screws holding the interior panel and the new exterior panel. Restore electrical power and enjoy the new look of the ss panel.

Lower basket was dry rotting

  • Customer: Barbara from Ballwin MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
Not being very computer literate, the most difficult part of the entire venture was navigating your web site. But I finally found the part I needed. I paid on line with a credit card, and received the part within a few days. I popped it in the dishwasher, and it took three days before my son noticed it.
He was surprised and I was proud to say " I ordered it on line."
All's well that end's well.
I would difinately use your service again.

Dishwasher wouldn't clean dishes

  • Customer: Valerie from Danbury CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench(Adjustable)
  • 5 of 8 people found this instruction helpful
First shut circuit breaker to dishwasher and close water valve under the sink. Remove the screws that hold the dishwasher to the counter, then remove the bottom cover plates. I slid the diswasher out almost all the way...On the left side bottom I could see the old water inlet valve was attached by 2 hex screws and a clip with 3 wires..after removing the 2 screws and clip I was able to remove the water line (place something to catch a small amount of water) and remove the black rubber hose from the old intake valve by squeezing the clip.. Removed the brass nut from the old valve you'll need it. I installed the new water inlet valve by connecting the old brass nut
(replace with new thread seal tape) , replace the water line and black rubber hose...attach to frame with the 2 hex screws and replace clip with wires...I slid the dishwasher back under the counter, turned the water on and power back on...I ran the dishwasher before I secured it in place to check for leaks...Dry as a bone...I then secured it to the counter and replaced the bottom plates.. the dishwasher is working like new...everything comes out spotless...Sometimes repairs are not as hard as they look, just take your time.

I couldn't fint the part any where--EXCEPT at PARTSELECT.com

  • Customer: Robert R. from Moore OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
I needed a simple clip for a fold-away dishwasher rack. MAYTAG was NO HELP--except they did supply me the right part number that MAYTAG posted on websites in error. MAYTAG said they could not ship it to me--not a consumer item!! Well, I found the part at PARTSELECT.com, I had it in three days and installed it in about 10 minutes. Our clip has been broken for 2 years and it ended up being a 10 minute fix!! GREAT JOB PARTSELECT.com!!!!

Dishes not getting clean - sandy residue on dishes.

  • Customer: Todd from Racine WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
There was a tear in the fine filter (fabric) on the accumulator. This can be seen by looking in dishwasher without having to disassemble anything. Food was being sucked in and sprayed back out on dishes.

Disassembled, cleaned, replaced part then reassembled.

Cleaned out the spinning sprayers -- used toothpicks to clean out holes, flushed with water.

Cleaned out under the accumulator.

Works like new.

Input water valve was cracked and leaking

  • Customer: Justin from University Park PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Pulled out the dishwasher, disconnected the electrical, water, and waste lines.Then removed 2 screws that held the valve in place, and the supply line. Swapped out the new valve for the old one, replaced dishwasher, reinstalled the water, electrical, and waste line. Turned the water valve on, checked for leaks, and fired the old dishwasher up.

Wheels on left side of middle rack broke.

  • Customer: Kayla from Lincoln NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 4 of 5 people found this instruction helpful
Initially ordered the rack adjuster assembly, not realizing that I would also need the adjuster lever and adjuster cover, too. This piece is NOT what originally came with our unit. The line drawing for part 17 shows what our unit looks like. That part has apparently been discontinued and we were guided by Maytag to order this substitution, which is actually a Whirlpool part. Thought someone else might want to know this if they happen to have the same series of Maytag DW as we do. It fits well onto the rack, however, the location of the wheels on the unit are different than the original which means that the middle rack now slides out of the dishwasher about 3" less than it used to, which is kind of a bummer. All that said, the repair was a piece of cake and the hubs on the wheels are now metal instead of the original plastic. . .I expect this part to last a good long while!

If you don't hold door when opening, it will drop down hard

  • Customer: Peter from Westbury NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
First I removed two bottom plates (two screws on each) Then I pulled dishwasher out about six inches. That's as far as it would go because I did not disconnect the water and drain hoses. That was enough to remove the broken cable and collect the disabled spring. I then reattached the new cable to the spring and reworked them into position. NOTE: There is a right and left cable and spring set-up. I used the "good" side as a guide. I then pushed the dishwasher back into place and replaced the two bottom plates.

The spinning wash arm above the glass rack broke off

  • Customer: Cynthia from Van Nuys CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
The part broke off a while ago, and I did not want to call a repair person. The machine still ran, so I ran it with the part missing - the glasses were not very clean, but the repair call was expensive...

I figured that I had a snowballs chance of finding the part number on a molded plastic piece with no numbers printed on it. Boy was I wrong. I was able to choose the part off of a schematic of my machine right on the website and it linked me to the right part order form, so I did not even have to go back and find it on a list.

When the part came, all I had to do was unclip the old mount- with my fingers- no tools, and snap in the new part.

A for maytag for making it easy to fix
A+ for PartSelect for making it so darn easy

Diswasher door would not latch properly. Plastic handle broken.

  • Customer: Richard from Simpsonville SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Received the entire latch/switch assembly rather than just the plastic latch handle. This was a pleasant surprise, especially for the price. The latch assembly was clearly a better designed and more robust assembly than the original.
Removed the inside panel of the door by removing the dozen or so TORX screws.
Pulled the inside panel away from the outside door panel (gently, cables attached) to gain access to the latch/switch assembly. A second set of hands was helpful for this and some following steps.
At that point the latch assembly was free mechanically from the door, but there were two wiring harnesses attached to the latch assembly via plug connectors to the two microswitches on the latch assembly. It looked like it was going to be easy to unplug the harness from the switches, but I could not do it. Never did figure out how to do it.
Removed the two microswitches (with harnesses attached) from the 'old' latch assembly by pulling back the plastic tab that holds each switch in place. At that point the rest of the latch assembly was completely free from the machine.
Removed the two microswitches from the 'new' latch assembly using the same method as above. This step requires care as the plastic parts and switches can be damaged.
Put in place the two 'old' microswitches with wiring harnesses attached on each side of the 'new' latch assembly. These snap in place. This requires care, as above, and the second set of hands to hold away the inside door panel.
Put the latch/switch assembly in place in the door, and put the inside door panel back in place.
Re-installed the TORX screws holding the inside door panel - and latch assembly - to the door.
I kept the 'new' microswitches because one day the 'old' switches may fail. If that happens and I want to replace the microswitches, I still don't know how I will remove the switches from the wiring harness. I guess I'll figure that out if the time comes.
Except for the difficulties disconnecting the microswitches from the harnesses, this was an easy and straightforward job. The latching of the door seems more positive, now, and the machine is working fine.
All Instructions for the MDB7600AWS
91-105 of 1,090