Models > MDB7600AWS > Instructions

MDB7600AWS Maytag Dishwasher - Instructions

All installation instructions for MDB7600AWS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB7600AWS
781-795 of 1,099
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door handle was broken

  • Customer: Mark from St Simons Island GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video you had available online, and the repair was as easy as the video demonstrated. There were no surprises and the dishwasher works like new.

door handle broke

  • Customer: bob from hastings NE
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
took the inside panel off removed the handle and safty switch and hooked up the new one and replaced the inside door panel. hardest part was unhooking the switch

Dishwasher door handle broken internally

  • Customer: William George from Eagan MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered the replacement door latch with switches because it came that way even tho I did not need the switches. While waiting for the part, I used two epoxy coated strips of cloth to repair the handle axle mounts. They held and probably are holding still. It took 10 minutes after the part arrived to replace my repair.

brokent lach

  • Customer: Mario from San Diego CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
install new part

The handle was broken

  • Customer: Dean from Enterprise AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
The repair went exactly like your video described! Your instructions were awesome, you got me the right part the first time and it was a total non-event repair. I will not call a repairmen in the future, I am a total customer... Thanks so for the assist...

plastic handle broke at a place it couldn't be repaired

  • Customer: Jerry from Rose Hill VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
used a torx driver to remove all the screws in the door unpluged the switches and put the new one back placing it back in the slot and replaced the screws a piece of cake.Took about 15 minutes.

Door was hard to open handle was loose

  • Customer: Jason from Tacoma WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I searched online and found several problems of the handle breaking. I removed the inside panel and found indeed the handle was broke. I searched several online stores and found all offered the handle in white but I needed black. I found parts select and they had the best price fast shipping and the correct color. A+

Door Latch Broken

  • Customer: Spencer from Yorktown VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed the inner door by removing 8-10 screws, unplugged two terminal leads, replaced new switch, attached terminal leads and fastened inner door back in place.

Hard to open door

  • Customer: James from Crescent City CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed about 10 screws (torx tip)and lifted out latch assembly. Removed both connectors from latch and installed in reverse order. No brainer.....

Broken Latch Handle

  • Customer: Michael from Latrobe PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed screws on the inside of the dishwasher door revealing broken part. Used schematic diagrams on the web site to identify and order the part. The old part was easily removed and replaced just by slipping off a couple of wires and slipping the new ones back on. They were a little difficult to pull loose, but I was prepared for that from reading a previous review on the Parts Select website. This gave me the confidence to keep pulling until I got them loose.

replaced door handle

  • Customer: Pamela from Vashon WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pretty easy. Saved myself a lot of money by doing it myself. The part was only $28 ! You can never get a repair man to come out for less than $150. I ordered the part standard shipping on a Friday and received it Tuesday. Oh... and I'm a girl!

Broken Latch on door

  • Customer: Brian from Canton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the screws to the inside door panel and simply removed the latch assembly. I had to pull off the two power ends and then placed the latch back in the door. I then plugged the power ends back up and screwed the door panel back on. The dishwasher works as good as new. Very easy fix.

Latch hadle failed...broke

  • Customer: Charles from Huntsville TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched the video, no problem.

dishwasher door was hard to open

  • Customer: Charles L from Elizabethtown KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and did exactly what he did to replace the handle and latch.

Broken door lstch assembly, not locking.

  • Customer: Roberto A from Clermont FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Sit on comfortable stool, in order to minimize back issues. Open door, use #27 torx screw driver and remove the screw top 7 screws around the inner perimeter of the door liner. Use flat screw driver to lift inner panel(just enough to pull unit out), pull out handle and door assembly with switches, pay attention to wire connections, use pliers to remove wire connectors and install on new unit making sure of correct position of new unit. Position latch assembly, make sure the mounting holes are positioned correctly, lower inner liner, temporarily attach two screws holding new unit in place (do not tighten all the way). replace remaining screws...tighten all screws until inner door liner in place, paying attention,do not over tighten screw. Test run unit. Perfect!
All Instructions for the MDB7600AWS
781-795 of 1,099