Models > MDB7600AWB > Instructions

MDB7600AWB Maytag Dishwasher - Instructions

All installation instructions for MDB7600AWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB7600AWB
76-90 of 1032
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the soap dispenser wouldn't open during cycle

  • Customer: paul from spring hill TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 5 of 6 people found this instruction helpful
I unscrewed the door panel. removed the plastic cover protecting the dispenser. unscrewed the dispenser (6 screws). I removed the old dispenser and put the new one on and put it all back together. It was pretty easy.

Dishwasher wasn't cleaning well, especially top rack

  • Customer: Casey from Wadsworth OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
I wanted to get the dishwasher cleaning better and thought that maybe the accumulator needed to be replaced. I figured that I'd swap out all the spray arms as well, just for good measure.

I needed Torx screwdrivers (T15 and T20, I think - not 100% sure on that) and patience because there's really quite a lot of screws to get the accumulator out. Finally got to it and it didn't look damaged, but replaced it anyway.

The spray arms are easy - they just snap in except for the lowest one, that had a plastic nut. I ordered a replacement nut just in case I broke this one (you know how that goes) taking it off. Well, it took pliers, but it came off ok.

In the end, my dishwasher is happy and cleans much better now.

Handle jammed and door wouldn't open on Maytag Quietseries 100 dishwasher

  • Customer: Philip from Carlsbad CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 9 people found this instruction helpful
I Followed others' instructions already posted to replace the whole handle assembly. In particular, use a big screwdriver placed against the bottom of the handle and whack the grip with the palm of your hand to get the handle to move back to the open position so you can open the door and start the job. I am no handyman, but this fix was easy, about 30 minutes in all, most of which was spent figuring out which breaker to pull so as not to get shocked. One note of caution: use the correct screwdriver attachment (not a Phillips head or regular, but a star or something- see I am not a handyman but I do have a $15 screwdriver set that just paid for itself 10 times over!).

drain line had split

  • Customer: William from Interlochen MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 6 of 10 people found this instruction helpful
disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes

Upper Rack not Cleaning

  • Customer: Stephen J from Sammamish WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
First I read all the reports for not cleaning properly already listed on this site. I had to replace the docking station with flappers. When I removed the station I lost the flappers down the water delivery tube just like Jon said I would in his repair post so I removed the water distribution assembly fished out the old flappers and snapped in the new.
But then I figured I might as well check out the accumulator while I was in the tub anyway - I had read that you need Torx screwdriver bit, which I had, undid the screws, pulled out the accumulator screen which was about 80% clogged, discovered I need a new chopper blade and my impeller is disintegrating, put it back together and lost ten minutes looking for the three screws I had incorrectly put in too soon, and now it is cleaning a packed full load like it was supposed to do.
**I love this site - I went to the virtual repairman and it listed every problem I had with this appliance in the order they happened (door latch broke years ago). - I think I am going to look up stuff that I own so I will know ahead what could go wrong with them.

And absolutely NO DUCT TAPE was used in this repair.

knob fell off, and burnt in the wash cycle.

  • Customer: Marcia from Plaistow NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
Simple. Unscrew the old one, replace with the new one.
The best part- Online said it would take 5-7 days to recieve thru the mail. It arrived the very next day!!!!

Weeping water control valve

  • Customer: Robert from Woodstock IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 4 of 4 people found this instruction helpful
Turned off water and power to the unit. Removed kick plate from under the dishwasher to access the water contol valve. Placed an absorbant rag under the water valve and water line. Disconnected solenoid on water control valve from electrical connection with my fingers. Used a standard adjustable wrench to disconnect the water line from the water control valve. Then used a 1/4" nut driver to loosen the two bolts that hold the water control valve on to the mounting bracket. Pulled the water control valve slightly forward to disconnect the water feed line to the dishwasher. Used a blunt end plier to pinch the clamp open and slowly wiggle the feed line off of the water control valve. Then removed 90 degree elbow off of the water control valve and used pipe dope and connected the elbow onto the new water control valve. Replaced water control valve in reverse order and utilized new hose clamp to reconnect feed line to new water control valve. Saved door seal for future use, when seal goes bad.

Dishwasher arm not spinning

  • Customer: Joseph from Warwick RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 4 of 4 people found this instruction helpful
I removed flowplate assembly, chopper assembly, found that the plastic spindle was stripped causing arm not to spin. In the new seal kit, the spindle was made of metal (much better design). I replaced the spindle, chopper, and filter assembly (old one was caked full of gunk). Worked like a charm. A previous post helped me figure out the problem.

humidity would seep out absorbing into the granite above

  • Customer: Eric from Overland Park KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
remove old seal, put in new - my 10 yr old could do it. Note - there is a white mark on the back of the seal indicating the middle so you can line it up when installing the new seal - makes it easier.

A wheel on the upper tray that moves in the slide broke.

  • Customer: Melvin from Rochester Hills MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Actual repair took less than 5 minutes. Removed 5 screws from original "adjuster' and removed the outside housing. Aligned the replacement part and simply replaced the five screws. Wheels on the replacement part are held in place with steel "rivets" while original wheels are all plastic and held in place with a screw . The replacement part is a much sturdier set-up. I saved the unbroken wheel from the original adjuster in the event a wheel on the right hand adjuster breaks.

If you don't hold door when opening, it will drop down hard

  • Customer: Peter from Westbury NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
First I removed two bottom plates (two screws on each) Then I pulled dishwasher out about six inches. That's as far as it would go because I did not disconnect the water and drain hoses. That was enough to remove the broken cable and collect the disabled spring. I then reattached the new cable to the spring and reworked them into position. NOTE: There is a right and left cable and spring set-up. I used the "good" side as a guide. I then pushed the dishwasher back into place and replaced the two bottom plates.

Water leak from the dishwasher door

  • Customer: Michael from Bronx NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
After replacing the door gasket and seeing that this wasn't the problem, using the schematics found at partselect.com I finally realized that it may be the insulation foam strip. I ordered the product and received it very quickly. Installation went fairly quickly. It was easy to remove the old foam strip and install the new one. The only problem was that the foam strip was about 1/4 " too short and it didn't cover the entire bottom. I improvised a little bit and cut off some of the old strip and covered the gap. So far the leak seems to have been fixed. In addition to the foam strip I had to buy a torx screwdriver for $11 at the local hardware store. The total spent was around $25.

Wheels on left side of middle rack broke.

  • Customer: Kayla from Lincoln NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 4 of 5 people found this instruction helpful
Initially ordered the rack adjuster assembly, not realizing that I would also need the adjuster lever and adjuster cover, too. This piece is NOT what originally came with our unit. The line drawing for part 17 shows what our unit looks like. That part has apparently been discontinued and we were guided by Maytag to order this substitution, which is actually a Whirlpool part. Thought someone else might want to know this if they happen to have the same series of Maytag DW as we do. It fits well onto the rack, however, the location of the wheels on the unit are different than the original which means that the middle rack now slides out of the dishwasher about 3" less than it used to, which is kind of a bummer. All that said, the repair was a piece of cake and the hubs on the wheels are now metal instead of the original plastic. . .I expect this part to last a good long while!

Input water valve was cracked and leaking

  • Customer: Justin from University Park PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Pulled out the dishwasher, disconnected the electrical, water, and waste lines.Then removed 2 screws that held the valve in place, and the supply line. Swapped out the new valve for the old one, replaced dishwasher, reinstalled the water, electrical, and waste line. Turned the water valve on, checked for leaks, and fired the old dishwasher up.

Our dishwasher would not take in water. It would partially fill but not to the level required to run properly.

  • Customer: Laurie from Cashton WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
I pulled the dishwasher out from under the countertop. It was quit easy to get to in the lower left front corner of the appliance. I loosened up the bracket that was holding the valve in place. Removed the wires, and taped and ID them so that I would know which one went where. Removed the hose clamp, pulled the hose off and removed the old valve. Put the new one back in just as I removed the old one in the same order. It was a snap! This is not the first time I have used PartSelect! Our evaporate fan went out on our refrigerator a couple years ago, replaced that. A shelf broke in our refrigerator twice, each one different at different times bought both from Part Select. This is the first place I look for help with repairs! I at least attempt to save money, then if it's too difficult I will hire a repairman. So Far, PartSelect has saved me a lot of money on doing it myself! Thanks PartSelect for making small repairs easy to tackle yourself, along with reasonable prices for parts!
All Instructions for the MDB7600AWB
76-90 of 1032