Models > MDB7600AWB > Instructions

MDB7600AWB Maytag Dishwasher - Instructions

All installation instructions for MDB7600AWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB7600AWB
841-855 of 1,091
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Door Handle

  • Customer: LARRY from HICKMAN, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed all screws except the bottom two, and then propped up the door cover to get at the latch assembly. The assembly lifts out, pull off, with difficulty, the two wire connectors. Plug connectors back into the new latch assembly, sit it back into it's position, put the screws back in and your done. Much easier than I thought it would be. Note: do not put the screws in the soap holder, as they show in the video, if you accidentally spill them out, they can roll down into the bottom of the dishwasher, not good!

Door Handle broke

  • Customer: Bill from Akron, OH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Found the part on your site(easy). Ordered the part. Received the part. Reviewed the video you provided. Installed the part. The whole process was so easy, I recommend this website to anyone having minor appliance problems.

broken handler

  • Customer: david from medina, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Went easy without a hitch.

Plastic door handle broke off

  • Customer: William from Webster, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the simple, but thorough video provided as a attachment sent with the shipping status e-mail. No problems!

Door Handle Broke

  • Customer: Michael from Topsham, ME
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
1st. I turned off power to the machine. Mine has a light switch on the wall nearby that I can just turn off. If you don't shut it off at the breaker box. 2nd. I unscrewed the interior of the door to investigate the problem, and find out what the part looks like. 3rd, I found and ordered the part on Maytag's website. It only took about 3 business days. That was about 2 days faster than I expected. 4th, I disconnected the wiring from the old door handle, using the pliers. Plugged in the new part. Situated it back into the machine and screwed the door interior back on. 5th, I tested the door handle for ease of operation. 6th, I re-applied power, and tested the machine. That Was SO EASY!!! If you are not sure on how to do this. There are several How to videos on the web site. Thank You Parts Select

The handles was brooken

  • Customer: Harvey from Lake Park, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The people at parts select were great. they even gave me a link to you tube that was helpful. the only issue I had was you tube link did not mention that they were just showing how to take off the handle and that if you were using the entire assembly you don't need to take off the handle. I followed the directions took the handle off when I didn't have to. But over all I don't think I could not have done it without your help.

Door latch handle loose due to worn latch assembly

  • Customer: Caroline from Bethesda, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed dishwasher door after turning of power. Pulled out worn latch assembly--this was a bit hard because even though the latch assembly works like a plug in an outlet, it was difficult to pry out. I was afraid of breaking something essential. The new piece easily attached and I just screwed the door back on. My first appliance repair ever!

Broken handle/door latch

  • Customer: Keith from Mt. Pleasant, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions from others on this website. Removed the screws holding on the door panel, removed the door latch, BUT I removed the wires and the micro switches from the old door latch. I re-used the old micro switches and removed the new micro switches from the new door handle, re-installed everything and had it back up and running within 15 minutes. Took only two days to receive the new door latch/handle from Part Select. Be sure and disconnect the power to the dishwasher! I have my dishwasher plugged into a wall outlet so I just un-plugged mine to work on it. Turn off the circuit breaker if yours is not plugged into a wall outlet. KK

Broken Latch Handle

  • Customer: Michael from Latrobe, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed screws on the inside of the dishwasher door revealing broken part. Used schematic diagrams on the web site to identify and order the part. The old part was easily removed and replaced just by slipping off a couple of wires and slipping the new ones back on. They were a little difficult to pull loose, but I was prepared for that from reading a previous review on the Parts Select website. This gave me the confidence to keep pulling until I got them loose.

The handle broke.

  • Customer: Marianne from Des Plaines, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The hardest part was finding the model number. within five minutes the new handle was wired in and the door put back together. Yay for my dishwasher!

door latch would not open

  • Customer: David from Cedar Falls, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed your u-tube instructions and replaced the broken door latch with the new one.

Latch handle was loose

  • Customer: Donald from Farmington, NM
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Switched off power at the circuit breaker and tested the electrical wire to insure power was off. I removed the inside door panel screws with a drill/driver and lifted the panel and that exposed the latch. I pried the 2 electrical connectors off the old latch assembly and disposed it. I then attached the electrical connectors on the new latch and set the latch in place. I installed the screws by setting the drill/driver on the lowest torque setting. I closed the door several times testing the latch. All worked fine.

Broken Handle Hinge, floppy useless handle

  • Customer: Chris from Mandeville, LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Electricity is live to the door when it is open - TURN OFF the CIRCUIT (got an uncomfortable buzz myself). Removed the interior plastic door liner (10 Torx screws), top middle two Torx screws also hold the handle in place to the door frame, pull the black and white wire connectors off the handle assembly (the hardest portion of the whole task), push them onto the new handle (black to black and white to white), and re-attache the door liner with the new handle in place. Part was an exact match and if I did it again it would be <10 minutes. ALternatively you can remove the new switches from the assembly and re-use the old switches if the handle is your only failure. The you have two new seitches in reserve if ever needed.

Handle on Door Latch Assembly broke

  • Customer: Anne from Malakoff, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
On line video at PartSelect instructions were excellent. I followed the instructions as outlined and it was a snap. I removed the screws, dislodged the broken assembly, inserted and placed the inside door cover with screws as video showed. It went exactly as it showed. Ran load immediately after and all is fine. Thanks for great parts, service and the instructions.

Latch on handle broke

  • Customer: lanette from temecula, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video to make sure I didn't do anything wrong and then did it. It probably took 5-10 minutes and works perfect.
All Instructions for the MDB7600AWB
841-855 of 1,091