Models > MDB7100AWW > Instructions

MDB7100AWW Maytag Dishwasher - Instructions

All installation instructions for MDB7100AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB7100AWW
721-735 of 848
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishwasher leaking at bottom of door.

  • Customer: William from Kennewick WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video provided with the Order Acknowledgement. Very Very simple and easy to do. This is without a doubt the best company I have ever dealt with online. Prompt, quick delivery and very professional. The only mistake I made was not ordering the O ring for the soap dispenser. I am in the process of ordering that right now. This is the go 2 place for appliance repairs for sure. You won't be disappointed in any way.

water leaked out of door.

  • Customer: Robin from Levittown PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced with new gasket and it works great.

Dishwasher leaking from door

  • Customer: Marlon from Hamilton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered parts on Saturday, and they arrived Tuesday. Followed the instructions in the video. It could not be easier. I may turn pro when I retire.

The gasket is press fit in a channel around the door

  • Customer: Roy from Shoreline WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Orient the gasket so that the more squishable hollow side of the gasket faces the door, and check that the length is sufficient to fill ths entire channel. The less compressible side goes into the channel, which requires some skill and strength to seat well. The flat portion of the more or less square gasket has two edges to it. What works best is to put the edge that is toward the inside of the dishwasher into the channel with your fingers, and then press in the other edge firmly with the small spatula of about 2 or 2and 1/2 inches until you can no longer see that edge. This is the visual indication it is seated. in the corners you may only be able to use a corner of the spatula.

water leak from between the inner and outer door panels

  • Customer: Troy from Nashville TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Installed a new grommet on the soap door latch. Replaced door seal at customer request. The door seal ordered was to short. Replaced door spring clips at customer request. Split the door, remove 2 screws from inside the inner panel, grommet is between the inner panel and latch mechanism. Line the new grommet before install.

water was leaking from the right side bottom of the dishwasher

  • Customer: John from Newport KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled the old rubber gasket off put the new one on and then took the back end of a kitchen knife to push it in all around the door to create a solid seal

The rubber around the door is corroded causing water to leak,

  • Customer: Katherine from Santa Barbara CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Well, I haven't gotten the right part yet. I'm such an idiot that I've ordered the wrong part twice now. So, figuring that 3's a charm, I'm going to try to get the right part now. I do have to say that Part Select has made it amazingly easy to return the parts. And both of the first 2 (wrong) parts arrived within 2 days of ordering. I'm pretty impressed with this company. Now, if I can just order the right part, I can tell you how the installation went!

door the soap dispenser stopped opening

  • Customer: steve from dummerston VT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
unscrewed 7 torx screws with the impact driver. removed the motor from the bracket. comes out pretty easily. moved wires aside. Pulled the wires off the motor using the pliers- one came off very hard, note where they go, corroded in place. installed the new motor by easily re-attaching the leads. Biggest surprise was that there were 2 motors. I initially replaced the lower one which did not solve the problem. When I replaced the upper, it worked. Not sure of the function of the lower motor. The upper one clearly fits into a slot which seems to attach to the doors.

Would not dispince soap

  • Customer: J. Robert from Rensselaer NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed inside door cover, removed wire connections, & removed what I would call a solenoid device. Then installed new one.

Soap dispenser failed to open

  • Customer: Thomas C from Knoxville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Opened circuit breaker feeding dishwasher Removed the 10 screws from the inside panel on the door. Unplugged two quick disconnect plugs. Removed the wax motor (actuating solenoid). Installed the new one from Parts Select. Reconnected the plugs. Replaced the cover and 10 screws. Turned the breaker on and ran a load of dishes. worked perfectly.

upper dish rack roller failed.

  • Customer: Archie from North Charleston SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the upper rack rail stops. Removed the upper rack by pulling outward until the rack rollers cleared the rails. Attached the new roller on the upper rack. You can look at the other undamaged rollers to see how they lock into place. re-install the upper rack by feeding the upper rack rollers back onto the rails. Install the rail stops back into the rail ends,and the job is complete. VERY EASY!

Top right hand wheel gadget needed to be replaced

  • Customer: SHIRLEY M. from WEYMOUTH MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Watched video you have on the site.... also read the first person's description - both very helpful...since I am 75 y.o.and a woman got my chair to sit and did exactly step by step and actually did it! So happy I wouldnt have to buy a new dishwasher YET - Emailed my friends and said if and when they need wheel replaced I can do for them!!! Thanks for all the help on site.

No water from rotating lower spray arm or center spindle; soap dispenser lid would not open.

  • Customer: ROBERT from MORTON IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Had service man: stated I would need new motor/pump at $400 complete. I didn't like the interior of new dishwashers. Nothing to lose, so I verified that the motor was working; reviewed short PartSelect video. Ref: very helpful PartSelect assembly diagrams with parts list. THANKS PS! Removed two dish racks (top rack: extend fully and flip the roller-keeper clips. Pull rollers and rack-pins apart) Then I started taking the pump apart all the way down to the pump base (fits into tub with seal - did not replace that seal). Very intuitive - some parts are tight and must be encouraged to come apart; take care of seals and o-rings; take notes of sequence if necessary. Look for parts requiring replacement. Unscrew Spray Tower Lower Extension Nozzle and lift off Spray Arm and two lower spray arm seals - check seals for wear. Unscrew pencil-like Spray Arm Support Nut. Cause: I found a totally-clogged Pump Housing Filter, a bit of steel wool about the size of my thumb (same size as water supply opening in bottom), and small piece of broken glass. Cleaned all parts coated with lime; new Pump Housing Filter (could not clean adequately). Cleaned the screens underside of filter support (difficult) with brush and wire. Replaced o-rings for Wash Impeller and Drain Impeller as a matter of principle. Only alignment requirement is with bottom water supplly hole. Everything works like new now! Recommendation: clean Pump Housing Filter annually.

Nasty appearing pump seal

  • Customer: Jerry from Nevada City CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Unscrew round keeper on top of spray arm -CCW. Lift off spray arm. Remove the six Torx head screws aroun pump housing. Lift off pump housing. Unplug unit and obtain a small piece of 2 x 4 wood to block up the motor underneath. Push the white plastic lever near the left side of motor towards the back to loosen the entire unit. Place the wood block uner the motor and you will see the seal is accessable inside the dishwasher. Remove the seal and very carefully clean the area that accepts the new seal. Remove the block and pull back on the white plastic lever. Done!

injector seal ring was leaking

  • Customer: James from San Marcos TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
simply replaced the ring and the water inlet injector, no tools need on that part of the repair
All Instructions for the MDB7100AWW
721-735 of 848