Models > MDB7100AWB > Instructions

MDB7100AWB Maytag Dishwasher - Instructions

All installation instructions for MDB7100AWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB7100AWB
46-60 of 824
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

silverware basket broken - replaced with new one

  • Customer: Linda from Owasso OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 12 of 12 people found this instruction helpful
I was able to remove the old handle and place it on the new basket - using only a screw driver.

The basket in our dishwasher had many broken parts on the bottom and the silverware kept falling through

  • Customer: Marge from Cranford NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 13 people found this instruction helpful
We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.

diswasher would not drain

  • Customer: Larry from Arlington VA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 15 of 22 people found this instruction helpful
1) turned off power to dishwasher
2) removed each piece of pump assembly (one at a time) from inside the dishwasher. I had no repair manual and didn't know that by rotating the lock lever under the dishwasher, I could have easily removed the entire pump assembly as a unit.
3) Reassmebled the pump assembly using new parts and installed in dishwasher.
4) Reconnected hoses and electrical connection
5) Turned power back on
6) Washed dishes... it's as good as new!!!!

Racks were rusted and the tines were breaking off

  • Customer: Loraine from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 17 people found this instruction helpful
The bottom rack was easiest, just picked it up out of the dishwasher and moved the sprayer and the silverware holder from the old rack to the new rack and set it back in the dishwasher. The top rack was a little tricky, it took a minute to figure out to remove the little end-caps on the runners and then it just slid out. Slid the new one in, replaced the caps and moved the upper rack basket. It took less than 15 minutes to fix and now it's like a brand new dishwasher!

Machine began making noise as if something had let go and was beating on the machine

  • Customer: Michael from Lost Creek WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 12 of 14 people found this instruction helpful
I removed the plastic retainer that held the lower spray arm in place. After removing the lower spray arm I was able to remove the 6 hex screws that held the cover over the filter screen and the discharge housing assembly. I was then able to remove the bolts that held the upper part of the discharge housing assembly, and replaced it with the new part that I received. The rest of the job was simply putting it back together.

Note: While repairing the broken part, I noticed a small leak under the machine around the float assembly. This was simple to fix. Remove the small lock ring on the bottom of the float. Pull the float out and clean the grease and soap scum out of it. Put it back in and attach the lock ring. No more leak and the water gets turned off when the float activates the switch. Something that everyone should check periodically.

loose top basket/

  • Customer: Wanda from Bay Shore NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 24 people found this instruction helpful
I had two problems with the dishwasher. The top basket was loose, but the main problem was a plastic part inside the bottom assembly.

The part was backordered, so I re-ordered it through Sears. They said it would arrive in two days. Theirs came in two weeks, and their customer service was terrible.

Your "backordered" part came in two days, even before it was supposed to come had the part not been back ordered. I am delighted with your customer service and your company.

The illustrations on your website were excellent. They helped us not only to identify the part, but to diagnose the problem.

This was my first purchase through your company and if I ever need parts again, there is absolutely no reason to go anywhere else.

You have an excellent company, and great website! I bookmarked your page for future purchases.

Rusted upper and lower racks, broken tines

  • Customer: Charles from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
Read the experiences here, very helpful. Bottom slides out first - really easy. The new part comes with rollers, you don't need to remove the old ones. Now the only problem, getting the sprayer off the bottom basket. Look carefullty, you must use a screwdriver to release one side of the sprayer, then it works off easily. Make sure you note the orientation of the base of the sprayer. Reverse steps above and you are done. New tray slides in. Our new tray was a bit wider than the old one so we needed to use a bit of pressure to "shrink" the back just a wee bit.

The upper is easy also. Since the rails are uneven, make sure you put the high rollers on the high side no matter what your wife told about how it is supposed to go in. The end caps snap inward and slide out of the rails. Easy once you know. The uneven rails are obvious once you notice. Total time was 45 minuts, 30 of which was figuring out how to get the sprayer off without damage.

Would be nice to know the factory recommendation for removing the sprayer.

Dishwasher had weak drainingf pressure, turned out to be the drain impeller.

  • Customer: William from Beaverton OR
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 11 of 12 people found this instruction helpful
After I ruled out a hose blockage I looked in the washer.

Took the washer assembly apart, pretty straight forward, used the parts diagrams on this site for help. Found the drain impellor was jammed with glass and had lost a lot of its fins.

Found exactly what I needed here. Had it back together in less than an hour, and it seems to be working like new.

water was dripping from the bottom of the front loading door. Over time this had seeped into the insulation foam strip and formed a solid encrustation within the foam strip.

  • Customer: Dan from Clarkston MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
The real cause of the leak had nothing to do with the foam strip. The latch for the front loading door at the top needed to be adjusted to hold the door in tighter to the rubber door seal. This simple adjustment stopped the leak but since the foam seal was all encrusted with dried detergent from probably years of absorbing the leak, I replaced it with your new foam strip. I used a screw driver with torx bit and removed the stainless screws holding the inner door to the outer door. Once these were separated I removed the old foam strip using a putty knife and lacquer thinner. Placing the new strip onto these cleaned surfaces was the easiest part of the whole repair.

Dishwasher would not work unless the door was held in with pressure.

  • Customer: Leonard from South Huntington NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
I removed the screws on the inside of the door. Removed the cover and changed door switch and holder and put the new one in. Replaced the cover
all in less than half an hour.

Pushbutton panel stuck in "Lock" mode.

  • Customer: Ray from Olathe KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 12 of 16 people found this instruction helpful
First I switched off the "Dishwasher" electrical breaker. I then removed the 7 screws holding the door panel together and lifted the inside panel, exposing the control assembly. I took a digital photo to document the wiring connections then pulled away the two clear plastic protective sheets and unscrewed the control assembly (two screws) then disconnected all wiring. To make access easier I also removed the door latch assembly held by one screw. I removed the control assembly and reversed the process to install the new part. Voilà! It worked!

No water in the washer barrel

  • Customer: Terry from Great Falls VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench set
  • 10 of 11 people found this instruction helpful
Diagnosed potential problem from scematic diagram found at Parts Select .Com by entering model #. It was very likely the inlet water solenoid. Tear down was simple: Turn off water, disconnect water lines to and from solenoid, disconnect two electric terminals and remove part by removing two screws from dishwasher chasis. Before you buy the new solenoid, unscrew the water inlet elbow from solenoid and check the filter/screen inside the solenoid to make sure it isn't clogged. Assuming it's not, order the replacement part and reinstall in reverse order. Be sure to use plumber's tape on screw connections to make sure there are no leaks..... Also for ease of acces, you'll need to turn the dishwaher down on it's front. Put towels down to cushion the front and keep the controls from contact with the floor. Good luck!!

heating element split open

  • Customer: Hadley from De Leon TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 9 of 9 people found this instruction helpful
I took the bottom cover off and pulled off 2 wires and removed 2 plastic nuts. I removed the old part and removed the O rings from the old part and installed the new heating element. Replaced the plastic nuts and the two wires. It was very simple. The hardest part was lying on my back to get to the wires and nuts.

soap door didn't open

  • Customer: Richard from Shelburne Falls MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
I took out both wax motors - tried switching the motors on the rinse dispenser and soap dispenser but they were both dead - new motors from partselect arrived fast - simple installation if you have the torx screwdriver for the door inner panel.

Leak in the hose that feeds the upper wash arm

  • Customer: Norman from Chappaqua NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 9 of 9 people found this instruction helpful
First I disconnected the dishwasher electric, water supply and discharge hoses. I then pulled the dishwasher out. After opening the door, I removed the retainer clip holding the upper wash arm, then the nut holding the top shower hose in place. Close the door and lean the dishwasher on its side to get at the underside where the other end of the hose is. Loosen the hose clamp and remove the top shower hose. Reassemble everything in reverse order. In hindsight, I didn't need to buy the new hose clamp or the tub top washer (I reused the originals). Good luck!
All Instructions for the MDB7100AWB
46-60 of 824