Models > MDB6000AWW > Instructions

MDB6000AWW Maytag Dishwasher - Instructions

All installation instructions for MDB6000AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB6000AWW
1-15 of 757
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water dripping from right corner of door

  • Customer: Tim from Ringgold GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 483 of 486 people found this instruction helpful
Took out about 7 torx screws to remove the inner door liner. Discovered evidence of leak coming from the sop dispenser latch, and noticed the grommet had turned soft and was torn. The grommet is only about 1" square. Used nut driver to remove two screws to remove latch assembly. Slipped old grommet off and put new one on, and reattached the latch. The foam seal at the bottom of the door looked worn, so we replaced it with weatherstripping from home improvement store. The main door seal was brittle, so we replaced it too - just grab an end and pull the old one out. The new one was installed by starting at one end and we just pushed it in place. We used a nut-driver to push it in - we were afraid a screwdriver might damage it. The new door seal required us to latch the door to get it to stay closed the fist couple of days, but now it has loosened up a bit and works as expected. And NO MORE LEAKS. Cost is much less than a new unit!

The dish rack had two sets of adjustable tines that had never worked.

  • Customer: frank from kenmore WA
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 464 of 465 people found this instruction helpful
I ordered two clips just in case. Turns out I needed both of them. Since I hadn't seen the adjustable tines installed, it took some time to figure out how to put the assembly together.

For some reason I had the dishwasher for 7 years before it occurred to me to order the replacement parts. It's much more efficient to use with the adjustable tines properly installed as I can load approximately 25% more plates than before.

Rack roller broke

  • Customer: Kathy from Lombard IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 461 of 462 people found this instruction helpful
I opened the end stop of the rack, replaced the roller, and put the end stop back on. I can't believe I paid the repairman the last time $125????? An he put in a regular screw that rusted and broke the roller. Took me 3 minutes! Thanks

The utensil basket was old, bowed and the bottom was falling out.

  • Customer: Janet from Plano TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 384 of 388 people found this instruction helpful
I ordered a new replacement basket. The new one is a little different but it fits in the same place and takes up the same amount of room in the dishwasher. It looks very nice too.

Clips to hold the folding tines on the bottom rack were broken; also replaced some wheels on same rack.

  • Customer: Penny from Perry UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 367 of 372 people found this instruction helpful
It took awhile to figure out how to install the peg clips; I still have my manual, but there is no diagram or picture to show how they are installed (and not on the internet either - not even Amana's site), but I figured it out... so here are the instructions I have created.

On the rear part of the lower rack, you will notice that there is a row of larger spaces between the bars; we are only concerned with the 3 farthest right spaces & the 6 bars that create them.

Install both clips with the ‘flange’ that wraps around the bar inside the square; this will position the clamps that hold the clip in place on the outside edge of the bar.

Place one clip on the far right bottom bar; place another clip on the left hand side of the 3rd space (4th bar from the bar the other clip was attached to on the right).

There are small ‘legs’ that protrude from the folding tines on one end of each; place the tines so that the 2 large tines on both are on the outside, the 4 straight tines are on the inside of the squares when they are folded down, which will put the little ‘legs’ down by the far left square.

Snap the tines into the small clamps on the ends of the clips, so that the loops on the ends will rotate up into the larger clamps when the straight tines are folded down, which will hold them in place.

The dishwasher roller axle needed to be repaired

  • Customer: Rosemary from Toms River NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 364 of 366 people found this instruction helpful
I watched the installlation video found on the wedsite and followed his directions.

2 broken wheels on basket

  • Customer: jeanne from waynesboro TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 362 of 364 people found this instruction helpful
unwrapped wheels ,pulled out drawer and easily put on new wheels...as we live way out in the boonies it was great to be able to order parts and have them delivered so fast...easy to fix....

Dishwasher leaking (small puddle)

  • Customer: Gregg from Woodbury MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 177 of 247 people found this instruction helpful
My dishwasher was leaking a small amount and it seemed to be happening during the last half of the cycle. The insulation at the bottom of the door was wet but not directly under the dishwasher by the motor etc. I tried the door gasket which was a simple 2 minute job but that didn't solve the issue. I took apart the door by removing the seven torx head screws on the inside (don't worry about the metal pieces on the sides with the phillips screws). I could see some white powdery build up and watermarks coming from the soap dispenser area. I thought maybe there was crack in the door. But after taking out the solonoid (it just snaps in and out) I could see light around the little latch that holds the soap dispenser door shut. I tried a bit of caulking but it just fell out after a day or so. Then I found the little grommet on PartsSelect.com. You have to take off a white plastic cover that covers the door latch mechanism - it snaps in and out on one point. A couple screws hold the plastic assembly in place. You can just remove the whole assembly, it doesn't need to be taken apart. Remove the old grey gasket around the latch and put the new one over the latch. It's more like a "boot" like around a shift lever in a car. Put the assembly back in with the latch going through the hole. Make sure the gasket covers the hole. Tighten the screws down, not so much as to tear the gasket but enough to be snug against it. Snap the white cover back on. Snap the solonoid back in place. Put the door back in place. Put the seven screws back in. You're all set - no leaks. The key to troubleshooting was that it started leaking during the rinse cycle after the soap dispenser latch had flipped up exposing the worn boot around the latch.

Maytag makes a really crappy silverware basket. The bottom of ours fell apart the first year.

  • Customer: Kenneth from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 135 of 202 people found this instruction helpful
There was no repair to be done. Just replaced the defective basket with the new one.
I got the part two days after ordering it. Great service.

The bottom of our dishwasher's old utinsel basket broke out

  • Customer: Wade from Seattle WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 97 of 98 people found this instruction helpful
It was so easy to find the right part on the PartsSelect website. I just had to enter the manufacturer (Maytag) and model number and up popped skematics of all the parts available. I just clicked on the drawing of the basket and placed the order. It took less that 5 minutes. The part arrived 4 days later as promised. The repair took even less time than teh ordering. I simply took the old basket out and dropped in the new one.

I'm just happy to know there is a place that has such a user friendly website and stocks so many parts for older appliances. I had my house built in 1992 and several of the appliance are original. Fortunately I always keep the owners manuals for every piece of equipment so the model and serial numbers are readily available.

dishes weren't getting cleaned

  • Customer: Josephine from Clearwater Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 90 of 106 people found this instruction helpful
1) Lower Spray Arm and Pump Housing Filter:
1a) Unscrewed lower spray arm cap. Removed lower spray arm. Removed metal radiant shields from lower spray arm, cleaned them, and snapped them onto the new lower spray arm.
1b) Removed Torx screws from pump cover, then removed pump cover.
1c) Curled new filter into circular shape, interlocking the tabs to connect the ends together, then replaced the old pump housing filter by removing the old filter and then pushing the new one into place in the pump cover. Old O-ring was fine, so didn't really need to replace it.
1d) Re-installed pump cover by aligning the water ports on the cover with those in the dishwasher, then pushing cover down into place, then installing and tightening the Torx screws. If I were to do this repair again, I would replace the pump cover with a new one.
1e) Installed the spray arm by placing the new lower spray arm into position over pump cover, then screwing in the lower spray arm cap.
2) Upper Spray Arm
2a) Removed upper spray arm by unscrewing the snap outlet nut, then removing the spray arm retainer. This way, the retainer is undamaged and can be re-used.
2b) Attached new upper spray arm to snap outlet nut by pushing old retainer through new upper spray arm and into snap outlet nut.
2c) Installed new upper spray arm by screwing snap outlet nut back into the dishwasher.

Dishwasher was leaking in the lower left hand corner from time to time.

  • Customer: Dina from Hammonton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 81 of 81 people found this instruction helpful
Using the pliers, my husband pulled out the old gasket to get it started. He then pushed the new gasket in with his fingers and used a screwdriver to press in the ends. That's it. Pretty easy. I ran the dishwasher a couple of hours after he installed it and there were no leaks. Still not leaking. Seems a bit quieter since the seal
is better.

I was secretly hoping for a new dishwasher eventually. But it makes much more sense to shell out $43 for the gasket rather than spend the $600 or better for a new dishwasher!

I found the website very easy to use as well. Everything shipped quickly and there were no problems at all. I will bookmark this in favorites should I need it again!

Pieces of the lower dishrack were loosing the plastic coating and snapping off.

  • Customer: Joy from Washington VT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 80 of 90 people found this instruction helpful
First of all, I removed the existing lower dishrack. That was a piece of cake! The part that was tricky was getting the spray arm out of the center so that it could be placed into the new dishrack. I finally figured out that I simply had to twist this piece (I think to the right) to remove it. I reversed this step to place the spray arm assembly into the new dishrack. And then VOILA...I just slid the new dishrack in place!

Water leaking below door

  • Customer: Jeff from Sandy UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 104 of 168 people found this instruction helpful
I originally thought the door gasket was leaking so I went to partselect on line to order the gasket. After seeing the repair story results, I also decided to order the soap dispenser grommet also. I first relaced the door gasket as that takes about 5 minutes (take the easy way first right,) I was wrong as it still leaked. I then took the 7 torx head screws off from the door and the inside section just lifts off exposing the underside and the real problem. The soap latch had been leaking and was obvious from the dried soap/water trail. You have to remove two small screws and the whole unit comes out very simply. I took the extra time to clean off the build up of soap and hard water before replacing the seal and remounting the soap dispensing latch assembly. Ran another load and no more leaks! Thanks for the advise and the really simple but accurate way to order parts. I will use this site if I ever need any other parts. Very helpful and quick deliver as well as reasonably priced.

Wheel had broken off along with the folding tines' clip

  • Customer: Gina from West Alexandria OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 130 of 254 people found this instruction helpful
All I had to do was to snap the parts into place. I also had someone come here to find a leak in my dishwasher. It was in the latch and seal that kept the soap dispenser closed. They wanted to charge me over $50 when the part only cost less than $9 with shipping. I just ordered it and installed it myself. Piece of cake!
All Instructions for the MDB6000AWW
1-15 of 757