Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MCG8000AWQ

MCG8000AWQ Maytag Dryer - Overview

Get Parts and Repair Help for MCG8000AWQ

If you know the dryer repair part you need, you can browse the list of all parts on the MCG8000AWQ, or you can search by name or part description. You can also find your part by where it is located on the MCG8000AWQ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for MCG8000AWQ parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$9.99

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

Order within the next 6 hrs and your part ships today!
$15.40

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them as a set. Both have to be operational for the gas valve to open.

Order within the next 6 hrs and your part ships today!
$16.63

Door Catch Kit

This kit comes in two pieces: the catch and the clip.

Order within the next 6 hrs and your part ships today!
$38.87

Blower Wheel

This wheel has a deep D-shaped shaft receptacle. The spring clamp is not included with this part.

Order within the next 6 hrs and your part ships today!
$11.29

Drum Glide and Cushion Kit

Pad has adhesive backing.

Order within the next 6 hrs and your part ships today!
$189.09

Drive Motor

This drive motor rotates the drum by turning the belt.

Order within the next 6 hrs and your part ships today!
$4.89

Screw

This screw is sold individually.

Order within the next 6 hrs and your part ships today!
$17.05

Liquid Propane to Natural Gas Conversion Kit

Order within the next 6 hrs and your part ships today!
$20.29

Blower Seal

Order within the next 6 hrs and your part ships today!
$18.75

Idler Spring

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer ran but would not heat

  • Customer: Gary from Haverhill, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 282 of 318 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more

Timer wasn't working (New Timer)

  • Customer: Joaquin from Las Vegas, NV
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 122 of 69 people found this instruction helpful
Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I ordered the coils for ... read more

Dryer flame goes out after about 8-minutes from start and won’t work again until a 15-minute rest.

  • Customer: andy from Bethesda, MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 98 of 52 people found this instruction helpful
There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils & the problem was co... read more