Parts That Fix Maytag Washer MAV7600AWW Burning smell
Burning smell is a commonly reported symptom for the MAV7600AWW Maytag Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your MAV7600AWW Maytag Washer that will fix Burning smell. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This washing machine drive belt is used with some clothes washers. This belt is all black in color and is made entirely of rubber.
Replacing your Maytag Washer Drive Belt - 52 inches long
Customer Repair Stories
Belt was slipping, belt particles on the floor
Thank you, Lester
you guys ship faster than anyone else. One day I order the part and a day or two later there it is. :)
-
Lester from Elk Grove, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Wife complained the spin dry not so good
Wife thinks everything is back to normal. Get a cool drink out of refrigerator while she carries on and thinks you are a hero.
Special note: Be sure water is out of washing machine. There are instructions on the internet but I have owned Maytags for over forty years and know belt replacements are occassionally replaced.
-
Stephen from Tehachapi, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
This motor is a 2 speed, 1/2 HP, 120V, 60Hz.
Replacing your Maytag Washer Motor with Pulley
Customer Repair Stories
broken motor pulley
-
leighton from staten island, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set, Wrench (Adjustable)
The belt and pulley on the drive motor broke
Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.
-
Michael from Warminster, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
This drain pump with pulley, also known as the washing machine drain pump assembly, is a pump with two ports. The function of this pump is to help expel water from your washing machine. The pump is activated after the spin speed has been maintained for a specific period of time and is driven by the same drive belt that also runs the transmission pulley. If your washer is not draining properly the pump could be clogged by a small object or could be broken and in need of replacing. Tools you will need for this repair include a 5/16 nut driver, a putty knife, a 3/8 socket with a ratchet, and a pair of slip joint pliers.
Replacing your Norge Washer Drain Pump with Pulley
Customer Repair Stories
Load Grinding/Rubbing Noise in Rinse and Spin Cycles
-
Doug from Port Richey, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
washing machine was making alot of noise
-
David from Boca Raton, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Wrench set
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If your machine is not draining properly or if it is noisy and shakes during operation, you may need to replace the drain pump. This is a redesigned part. The pump now mounts on to the base of the washer. This product is made of white plastic and has a metal center. Before you can replace the drain pump, you will have to disengage the drive belt under the machine. To reach the drain pump you will need to remove the access panel on the backside of the washing machine.
Replacing your Maytag Washer Washer Drain Pump
Customer Repair Stories
Skreeching noise during spin cycle
-
Robert from Mesa, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
bearing on water pump siezed
-
kevin from rochester, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers
This part is the replacement motor pivot spring for your washer. It is made of metal and is approximately 3 inches long and 2 inches wide. The motor pivot spring helps hold the drive motor in the correct position on the motor plate. If your drive motor shakes during use, if the pumps will not operate, or if your washer is excessively loud during operation, you may need to replace the motor pivot spring. Be sure to disconnect the washer from the power source before you begin this repair. This part is sold individually and is an OEM part sourced directly from the manufacturer.
Replacing your Maytag Washer Motor Pivot Spring
This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race washer. These genuine Whirlpool parts are plastic and are not sold individually. The kit is used to help the washer drain, and may need to be replaced if the washer is experiencing slow or no spin, will not drain, or has no agitation. The washer will need to be tilted on its back or side to access the bottom. The tools needed to complete this repair are a small flat blade screw driver and a pair of slip joint pliers.
Replacing your Maytag Washer Transmission Pulley and Bearing Kit
Customer Repair Stories
washer would not spin water out in heavy loads
-
marcus from mansfield, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
washer would agitate, drain, but would not spin
-
michael from mountain home, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)