Models > MAV7600AWW > Instructions

MAV7600AWW Maytag Washer - Instructions

All installation instructions for MAV7600AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MAV7600AWW
76-90 of 332
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

MAKING NOISE DURING WASH CYCLE

  • Customer: MARK from HEBRON KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 8 of 15 people found this instruction helpful
REMOVED EXCESS WATER,REMOVED HOSES,TIPED BACK WASHER,REMOVED BELT,REMOVED PULLEY AND BEARING.REMOVED 3 SCREWS AND REPLACED WITH 3 LONGER SCREWS IN THE STATOR,THEN REMOVED 3 SHORTER SCREWS.THEN LOOSEN VERY SLOWLY EACH OF LONGER SCREWS TO RELIEVE PRESSURE FROM THE BRAKE SPRING.ONCE LOOSE,PULLED OUT BRAKE ROTOR.REPLACED WITH NEW PARTS.WORKS LIKE NEW.

washer making pounding and rocking sound

  • Customer: serenade from charleston SC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Took a screwdriver and pried up the top of washer, then reached in and unscrewed the front two screws that allowed the front to be lifted off.
Removed two screws on lower right side that allowed us to pry open right side of washer. There are six springs along the bottom of washer that keep the tub stable and keep it from bouncing against sides while in spin mode. One of the springs broke and needed to be replaced. Off course it was the one that was in the far back and the hardest to get too. But by prying open the right side it was reachable. The wife pushed against the tub to make the spring stretch a little less but still was too difficult. We took the advice of another home repair guy and put quarters in the spring (about $1.75 worth) to make it stretch out, then it was simple to connect the two ends, remove the quarters and voila....it was done. Screwed theright side back on, but the minimum order on the springs was six and the others seemed fine, we just put the other five inside the washer cabinet, replaced the front panel, reset the clamps on top of the front panel, slammed the top down and we were back in business. The parts including shipping was a little over $10.00. So I am sure we saved at least $140 repair job.

Machine making a grinding noise during spin cycle

  • Customer: Ines from West Babylon NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
On this particular model #MAV7550AWW Maytag washer, you do not remove a back panel since it is a three sided case. I first disconnected power and hoses from wall. Removed the belt from under the machine (you need to tilt the machine). To access the water pump you need to remove the front panel by first sliding a putty knife between the top of the machine and the panel slide it in about 2 inches from the edge to release the latch, repeat the procedure on the other side. On the inside or the panel about 2 inches there is a nut on either side once you remove both the front panel unlatches easily, from the bottom two latches. The water pump is located on the right front of the bottom plate. it is held in by three nut screws, (have plenty of towels to catch the water that is released once you disconnect the two hoses that are on the pump. The replacement part (made in the USA) is all plastic but fits perfectly. We Replaced the pump and reconnected everything. There is a video here on this site the explains in detail the removal and placement of the drive belt. The job is very simple to do. I am a woman under 5ft and I did this repair with the help of my son (17yr old). The machine is good as new. Second repair I have done on the machine and with a lot of savings!.

shakes, noisey

  • Customer: Dan from Lafayette CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Removed the waterlines. Set the ends in a small pan or bucket to catch the water.Do the same with the drain line.
Keep an old towell handy as water will drain out of the drain pump when you remove the drain hose. Removed the back panel. Use a flat bladed screw driver to pop the top off the two clips in front holding the top down. Lift the top and pull the two screws which holds the front in place. Remove the front and set aside. Underneath, use gloves and the screw driver to remove the six springs by placing the screwdriver through the top hook end about an inch and with both hands lift the spring off. Carefull not to let the blade slip off and bust your knuckles on something,hence the gloves. Lean the machine over and walk the belt off the pulley. Disconnect the small tube in the back left corner from the drum and lift the unit out from the top. Set the drum on it's top and loosen the six screws under the big pulley just enough to pull the snubber out. Replace new snubber, tighten screws. Set drum back in place and reattach springs. Lean unit over and replace belt. Reconnect the small tube, back left corner. Replace the front panel and top. Connect the drain line and replace the rear panel. Connect waterlines and check for leaks. I went ahead and replaced all springs. I recommend replacing the belt while your at it. I'm wishing I would have. It runs like new, gets more water out on the spin cycle and the dryer dosn't take as long to dry the clothes.

The washer was making a fine squeeling noise that created a foul burning odor

  • Customer: SONY from CONCORD NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
Took the washer outside, turned the washer on its side to expose the bottom panel. Removed the old water pump (three screws and two hoses. Replaced with new water pump and connected all fittings. Real easy to do. Washer runs great now.

The auger section of this part would no longer stay attached to the lower agitator part due to prior repair work

  • Customer: John from Ava MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 4 of 4 people found this instruction helpful
Use a blade to pop off the fabric softener dispenser cup. Use socket and extension to unscrew the single hex bolt that attaches the assembly to the shaft. Lift off the assembly and recover the flat washer. Install the new assembly over the shaft and install the original hex bolt and washer. Tighten firmly. Snap the dispenser cup back in place.

The washer would stick in between cycles and not continue

  • Customer: Gary from Red Lion PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
Removed the back panel from the control panel which was 3 phillips head screws and 2 hex screws. Remove the front knob from the timer, this is completed by removing the round center plate on the knob by simply pulling it off and then remove the small plastic pin in the center of the knod underneath the round plate. The pin holds the knob in place and once removed the knob can be pulled off along with the plate behind it.

Now from the back inside the contrlo panel simply unplug the wiring harness from the timer. Remove the circuit board from the timer also, it pulls off easily. There is one hex head screw holding the timer in place and once removed the entire timer assembly can be removed by rerleasing the right side and sliding the assembly to the right and out.

Slide the new timer in place, secure with the hex head screw, reconnect the wiring harness and press the circuit board back in place on the bottom of the new timer. Close up the back panel and replace the front knob components onto the new timer and you are ready to go. In all it took about 40 minutes and saved me over $200 for a service call.

washer was squeeling to a stop

  • Customer: paul from newbern TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 5 of 7 people found this instruction helpful
first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy

Broken fins on agitator.

  • Customer: John from Douglassville PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 4 of 4 people found this instruction helpful
I went ot the Parts Select web site, and read what other people had done with the same problem. The advice was right on. Using the paper towel to hold the screw in place during reassembly ws great advice. Thanks for the heads- up.

Fans on the Agitator had broken off.

  • Customer: Frank from Bethel Park PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 8 people found this instruction helpful
I popped off the fabric softener on top of the agitator. Used an extended arm on my socket set to remove the only nut holding the agitator on the motor assembly apparatus. The agitator came off with ease. Just reversed the procedure in replacing the new agitator. This was an easy job.

Water pump failure

  • Customer: John from Alhambra CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 4 of 5 people found this instruction helpful
Disconnect electricity....remove front panel by gently prying up lid.... Remove two small screws at corners of front panel. You may need small nutdriver here or very small hands, you can easily swivel tub out of the way....once front panel is off water pump is at the bottom right... It is only connected by two squeeze clamps and 3 nuts... This is obviously where the adjustable wrench and nutdriver come in very handy... Otherwise this job will be a bit longer....be prepared for residual water to pour out...you will need towels or a bucket....replace old with new one by reversing the process...at this point tilt the entire washer on it's backside or at least at a 45 degree angle to access the bottom... Swivel the motor away to slack up the belt...remove belt and replace in reverse order of diassembling.... Should take no more than 15 minutes.... Good luck!!!!!

Belt was slipping, belt particles on the floor

  • Customer: Lester from Elk Grove CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 4 of 5 people found this instruction helpful
I removed the screws to loosen the belt, took off the old belt and put on the new belt. Tightened it up and has been working ever since.

Thank you, Lester

you guys ship faster than anyone else. One day I order the part and a day or two later there it is. :)

White fluffy residue appeared under washer. Unbalanced banging during spin cycle

  • Customer: John from Blue Bell PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.

Squeeling noise at the end of the spin cycle. Not all of water is spun out. Clothes still wet.

  • Customer: Stuart from Erskine MN
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 8 people found this instruction helpful
My Maytag Atlantis MAV7550AWW does not have a side inspection door like many have posted. After taking most of the washing machine apart I noticed in the front between the top lid and the main body there appeared what looked like some type of clips. I used a butter knife and pushed the V clip back and the one side of the top lid was released. After doing the other clip it was clear that was how to access the motor etc. After the top was open, it's hinged by a plastic hinge, you will need a small wrench and have to move the tub to the side to take off two small nuts also in the front. 8mm I think. Then the entire front of the machine comes off and the pump was right there. Time to remove and install the new pump was 15 minutes. I replaced the belt at this time also but had to lay the washer on it's side. Put the belt on two of the pulleys and pull hard. You will see that one of them is a spring held tightener. I did this outside on the deck as you will have water in the hoses and pump. After all was hooked up I ran a wash cycle only to hear that screeching sound was still there. My best guess is that it's a tub motor going. I am just going to use the washer till it dies then get a new one.

Washer would fill, but not spin, agitate of drain

  • Customer: Mathew from Fort Collins CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Very simple, Lid cam part was broken, Just need to remove broken plastic lid cam with screwdriver and then snap in place the new piece. Worked like a charm first time. Easy , inexpensive repair to a reliable washing machine. Bill
All Instructions for the MAV7600AWW
76-90 of 332