Models > MAV7600AWW > Instructions

MAV7600AWW Maytag Washer - Instructions

All installation instructions for MAV7600AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MAV7600AWW
286-300 of 332
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

noise sound,very loud while running in all cycles.

  • Customer: Thomas F. from Lady Lake FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
view video on how to remove belts, motor and water pump. I follow the instruction given. the video is very helpful, gave me all I needed to do the job myself. thanks tom

bearings ground to a halt

  • Customer: edward from dunedin FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
Disconnected in and out hoses. Unscrewed part, screwed in new, reconnected hoses, installed belt and cover panel. Stood up the machine and tested. Good to go.

Loud screech at end of each cycle and knocking sound from bearings going out.

  • Customer: Don from Osceola IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Tipped washer backwards and removed belt from all three pulleys. Stood washer upright again and removed back panel around pump(4-screws)Removed drain hose from house drain and emptied excess water in the pump into a bucket. Removed the hoses from the drain pump then removed the three bolts holding the pump in place. Removed damaged pump and replaced with new drain pump. Reassembled in reverse order. Once the pump cover was replaced, tipped machine on its back, replaced the belt onto the three pulleys and promptly returned machine to its upright position and ran a test load of laundry! Success! Works great!

In spin cycle, made a loud nosie

  • Customer: Vicki from Pollard AR
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Took the back off, located problem, ordered part, removed old part, installed new one, tilled washer to put belt back on. Whole process not bad at all. Working with this site was so very helpful, will keep in in my favorites or future use. Thank You Parts Select!

Bad bearing on pump

  • Customer: Lon from Monterey TN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Lay the washer on it's side and remove the drive belt. Set back upright. Pry top cover up. Use a small flat bar and try not to damage the porceline. Two hex head screws (one on each side by the tub)holds the frone panel on. Remove those. Panel can now be tilted forward and removed. Pump is on right side. remove the two hoses and save the clamps. remove the three hex head screws holding the pump. Install the new pump and reassemble. Pretty easy.

change out pump bearing wore out

  • Customer: Bennett from russiaville IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unhook water lines after shutting off water, unplug power cord.Then move washer out into open space for easy access. Used flat tip driver to push in the spring clip to open the top of washer. Flip top up and had wife tilt the washer back. Once bottom is exposed took belt off the motor pulley. Let washer back down. Use the socket wrench to take out two ( front corners ) screws. Tilt front panel back and lift out off the clips . Water pump is front right corner. Use socket wrench to take out the three screws that form a triangle. Lift out the pump. Have something to catch water from pump . Use pliers to remove the two clamps spring from the hoses . Remove both hose from the pump. Then install new pump in the reverse order and close up washer in reverse order and put belt on . Replace washer in it place reinstall water line and lastly the power cord needs tobe pulg in. Now test the washer.

Had a difficult time getting the last washer on the transmission pully

  • Customer: Vickie from Harrison MI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the video

Washer would fill with water but would not agitate (which agitated the heck out of me...)

  • Customer: Veronica from Lake Forest Park WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I unplugged the machine and removed the top three screws and the corresponding bolts to gain access to the inside of the washer. I immediately saw the switch that needed to be replaced, unplugged the wire connection, and released the defective switch. I snapped the new switch in place,plugged in the wire connection, and replaced the screws and bolts. Then I replaced the switch cam, which took about five seconds. I plugged in the machine and it works!!! This is the first time that I have ever attempted to repair anything electrical. It was your website that gave me access to diagnose the problem, purchase the correct parts, and instruction on how to proceed with the repair. Thank you for your website!

Washer not spinning

  • Customer: Preston from Loxahatchee FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Popped in new lid part and working like new. Thought we would have to buy new . Thank you parts select shipped quickly and very easy fix.

Washer would not spin

  • Customer: Steve from Polo MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After inspecting the brake and installing the new pulley/bearing kit the washer still would only spin slowly. Discovered that if the washer agitates at all in the spin cycle then the transmission is shot. So washer was replaced with a new one.

suspect motor bearings. squeeling and smelled burning

  • Customer: Peter from Voorhees NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed your excellent video instructions to change out the motor.

pump went out

  • Customer: Donald from Hillsdale MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
1st open the front, 2 springs about 4" in from corners push back with a puddy knife tip back remove belt, remove two hoses, 3 bolts, put back together

transmission bearing melted ..

  • Customer: Louis from Dozier AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
put a total new transmission total kit on.

The E clip (or C clip) is not easy to install!

  • Customer: TRUONG from LAKEWOOD CA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I was struggling for more than an hour trying to put the E clip on with the thicker washer as recommended then gave it up. I tried again with the thinner washer and still can not get the clip fully seated in place (only one end got into the groove). Frustrated, I decided to tap the other end with flat screw driver and hammer. The clip seems to be deformed but rested in the groove. Checked the brake adjustment and it was on the min mark. I did not dare to remove it for adjustment, and there is no thinner washer to adjust anyway. The washer is still working OK now after 3 loads. Other than that I am really happy with the purchase. Supper fast shipping. Very helpful instruction video. Only I am not really a handy man as my wife often encourages!

Terrible squeaking with klunking, grinding and wet clothes

  • Customer: DawgGonGoodies from Clovis CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Well, I am a single mom on a limited budget and decided to tackle this project myself without having to call a repairman. After investigating the source of my noises online, I decided my washer needed the drive belt and transmission pulley/bearing kit. I unplugged the washer and using my teenage daughter to hold the leaning washer, I was able to easily remove the belt, which was frayed in one area. Following the online video, I removed the cap with ease. Reading about the e-ring being difficult to remove, I used a flathead screwdriver and a hammer to take this off. Then, I removed the washer and cam with no issues. I had a very difficult time removing my pulley though… it did not just slide off like the video! I ended up waiting for my daughters boyfriend to show-up and help remove this. He struggled as well, but once it was off, everything else followed easily. We then put the new pieces on in order and had no issues until the end. We were not able to pull the transmission shaft out, so there was no room for a washer to be placed after the cam was put back on. I ended up using the e-ring only to keep it all on before placing the new dust cap back on. Overall, this was a fairly easy installation. The washer sounds like new. I did notice on my last load that the clothes were pretty wet and think the pump may be next on the list. Not surprising for a 14yo washer and yes, I will tackle that myself too!
All Instructions for the MAV7600AWW
286-300 of 332