Models > MAV6200AWW > Instructions

MAV6200AWW Maytag Washer - Instructions

All installation instructions for MAV6200AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MAV6200AWW
61-75 of 335
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

terrible grinding noise

  • Customer: ALVA K from chippewa falls WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 9 of 10 people found this instruction helpful
For safety I Unplugged the machine
Tipped machine back and removed the belt. Rotated the motor by hand and all is well there. Rotated the water pump by hand and a grinding sound appeared. I Let the machine down . Using a hard object , 1/16th of an inch thick, I slide it between the front edge of the lid and the front panel unlocking the clips ( one on the right side and one on the left side ) holding the lid down. I then tipped the lid up and removed the 2 screws holding the front panel on. Lifted the front panel off of the clips on the bottom end of panel. Using a nut driver I removed the 3 bolts holding the pump to the frame. Then with a pliers I removed the clips holding the 2 hoses. With a pan to catch the water I removed the hoses and drained them into the pan.
I then took my machine model number and went to the internet in search of a new water pump. After checking several sites with no success, I come upon the site for PartSelect.Com. With the excellent search method on the site I was able to quickly find the part I needed. I placed my order (10pm) on a Tuesday night and a short time later I received an email letting me know they had my order. On Wednesday I received an email letting me know they had shipped my order. On Friday the order had arrived.
I removed the new pump from the box and inspected it . Every thing looks great. I placed the pump into its mount on machine and bolted it down. Attached the 2 hoses, put the front panel back on and tipped the top down into place. Pushed machine into place, plugged it in and fired it up. I now have a quiet running machine again. Thank You to PartSelect.com for the quick response to my

peice worn out, not letting washer cycle after filling

  • Customer: Anthony from DeKalb IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
Other peice broken or worn out. Poped old one off and new one in......YAHOO!! back to washing clothing again......

Washer completely stopped and would not run.

  • Customer: Alan from Carrollton GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 8 people found this instruction helpful
My timer was not working properly, it had to be turned to start each cycle and it would not move to the rinse cycle after the wash cycle - but it did run. I did not want to put out $70 or $80 bucks if I could make it work - but then it completely stopped. (The washer got off balance due to the load and would not run, after bouncing around on the floor.) The washer was getting power, since the pump would work and it would fill with water - but would not start the wash cycle. I ordered a new timer and put it in, which was pretty easy. First you unplug the unit, you don't want to get a shock. There are three screws on the back of the control panel that are removed with a phillips head screwdriver. The panel is then leaned/titled forward and the four plastic fins pull out of the slots, make sure you tilt it forward as you remove it and do not break off the fins/pins. Unplug the old timer and remove one nut holding it down. In order to remove the timer you have to remove the knob on the front. To do this you have to pull the small cosmetic cover off of the front of the knob - which you can pop off with a small screwdirver - it is in the very center of the knob. Once the small cover is off there is a small clip, pull it out and the knob will come off easily. Pull the timer out of the back of the control panel and put the new timer back in, plug in the timer and put the nut back on to hold it. Replace the knob, clip and cover on the front. Push the fins/pins back into the holes, replace the screws and you should be ready to go once you plug it back in. In my case it still would not run and my problem ended up being the lid switch. I figured this out by holding the button down with a pair of pliers and the washer started. I knew then that the switch needed to be adjusted. When the machine got off balance, the bouncing caused the lid switch to get out of place. I had to remove the control panel again and the lid, which is held on by two clips, that are easy to remove (only need to remove one), carefully put a small screw dirver under the clip and lift it up, then pop it off. You can then adjust the button, which has two parts, the switch and the push rod. This was the hardest part of the repair. The switch is not really put in well, looks like it should pop in to the slot, but would not allow the swith and push rod to work together. It sits on top of the opening. It took several tries to finally get it back right and adjusted with the push rod in the right place, but once I got it adjusted, replaced the lid, put the control panel back, plugged it in - it ran like a top. The new timer runs until the cycle is complete.

would'nt wash w/out getting hot

  • Customer: Emery from Talladega AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 9 of 12 people found this instruction helpful
just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go

original Factory Water Pump Bearing seized up

  • Customer: Bill from Mount Pleasant MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 8 of 9 people found this instruction helpful
Vey Easy to Fix. 1)Turn Water off at the wall. 2)Remove access panel on back of washer. 3) Remove Water pump. It is bolted down to the bottom of the washer by three nut head bolts. when loose the pump can be manipulated and tilted so the belt will have slack and most likely fall right off. Have a bucket ready. Remove water hose from top of pump by sgueaing clam with pliars and sliding clamp up hose. allow to drain in bucket. Lift drain hose out from wall and allow to drain through the pump into bucket. remove hose from pump that goet to drain. Replace pump and reverse steps listed above.

would not drain/slow spin

  • Customer: Carlos from Georgetown TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 9 of 14 people found this instruction helpful
i did the repair by the instructions that you had on the web site,and i thank you for all the help you gave me.

during wash cycle, water poured out of bottom of washer

  • Customer: Susan from Cloquet MN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 9 of 15 people found this instruction helpful
first we looked at schematics on your web site to see what we thought was wrong and if we felt we could do ourselves. It appeared to be seals and gaskets, so we went for it and carefully took the washer apart. We ordered the parts, cleaned the parts we had such as the tub, and were all ready to put back together when the parts arrived. Again, using your pictures, we reasselbled and when we tested, it worked better than it had been in a long time. And we saved a large repair bill!

Auger was broken

  • Customer: Charles F from Brooklyn OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
Needed a medium extension and a rachet a screw driver and a 13mm socket. I used a short screw driver and inserted in it the softer container and lifted it strait up to get the softner container out of the way. I used the medium extension to reach in the auger and loosen the small bolt holding the auger on the machine. Pulled it up and out. Reversed the above procedure and it was set to go. Total time about 8 to 10 minutes. Thank for all the help Kudos to all including Susan W.

Water leaking under washer. Tub to pump hose sprung a leak.

  • Customer: Richard from Cedar Park TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
There are two clips that hold the top of the washer down. Releasing these clips allows you to lift the top; it is hinged at the back. Then remove two screws holding the front panel and remove the front panel. The tub to pump hose is easily accessible. It is held in place by a hose clamp at each end. Use pliers to squeeze the clamps and remove the hose. Replace with new hose. I re-used the original clamps.

soap dispenser wouldn't open

  • Customer: Daniel from Flushing MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 6 of 6 people found this instruction helpful
Remove inner door by removing 7 torx screws. flip inner door up, propping it between the open door and the countertop.

Leave the drying solution reservour in place, remove two screws holding wax motor retainer. remove motor. (You might want to dissassemble door latch mechanism and replace latch seal, which is probably why wax motor failed to begin with. it simply slides over the latch FROM THE INSIDE.) Then reassemble.

I also cleaned up the main inner door seal. after that, the dishwasher leaked pretty good everytime the sprayer arm revolved. It took awhile to figure out I had rubbed off some rubber, although not much, BUT ENOUGH to make it leak.

SIMPLE FIX: Simply pull out seal, TURN IT OVER, so the back is now the front, AND RE-INSERT. No more leak. Saved 42 dollars.

Also: if your washer has two wax motors, (and you don't use drying agent) just swap the drying agent wax motor with defective soap dispenser motor. No cost repair.

Auger top would hit the top lid

  • Customer: Robert from Suisun City CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 6 of 6 people found this instruction helpful
The replacement was very easy, just one bolt and RR was a snap. However, the first part that came was defective and I called the 800 number, spoke to the rep and the part came the next day. Excellent customer service, and would do business again

washer would not spin.

  • Customer: Robert from South Gibson PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 10 people found this instruction helpful
tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!

Washer would stop running during the wash cycle

  • Customer: David from Mentor OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 7 people found this instruction helpful
1, Unplug unit from power outlet. 2, Removed 3 screws on the top back control console, 3, pushed bottom section back (standing in front) and tip top section foward, console then will lay flat on top of the washer, 4, remove wire connector, 5, remove 1/4 " screw lower left side, 6, lift locking tap up and slide timer to the left. 7, Set new timer in place and reverse the procedure starting with step 6.

Water Pump was making loud noises

  • Customer: Thomas from Bel Air MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 6 of 7 people found this instruction helpful
After pulling the machine away from the wall and turning off the water and unpluging. I simply removed the panel in the back and reached underneath and removed the belt. Took off the hose clamps and removed the three screws holding the pump on. Put the new pump back in place and hooked up the hoses. Then put the belt on for a test run.......all OK put the back on and was done. Whole job about twenty minutes. Saved over two hundred dollars doing this myself. Very simple repair.

washer agitator fins snapped off

  • Customer: Paul from ATLANTIC HIGHLANDS NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set, Wrench(Adjustable)
  • 6 of 8 people found this instruction helpful
I first took the fabric softener dispenser off and used
a ratchet wrench to take the nut off. I then removed
the agitator, put the new one on and reversed the process. It was extremely easy!
All Instructions for the MAV6200AWW
61-75 of 335