Models > MAH6700AWW > Instructions

MAH6700AWW Maytag Washer - Instructions

All installation instructions for MAH6700AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MAH6700AWW
61-73 of 73
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drain pump

  • Customer: Kimberly from Clinton MS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took back panel off. Replaced the drain pump

Outside door broke at hinge on front load washer

  • Customer: Jeff from Tunnel Hill GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Service repair tech ordered the outside door part and the door safety piece. (plastic shield that covers the glass inside door.) Outside door piece came in within week. Could not get other part in (backordered). Found online and had it within 4 days. Two screws hold hinge on to washer front. After removing hinge screws, pick up on door to clear the tabs on back of hinge through the tab holes in the back hinge brace. (This does not have to be removed. After removing door, unscrewed all screws in back of door to disassemble. Removed hing from hinge slots on door front and inserted into new door hinge slots. Snapped new door safety onto back of new door front by aligning tabs on door safety and outer door piece. Replaced glass bowl and door back by replacing screws in screw holes and tighten. Reattached door by inserting tabs on back of hinge into tabs on washer front and tightening hinge screws.

The latch was broken so that the front door wouldn't close.

  • Customer: Jennifer from Staunton VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the guy on the video. The only parts that were tough was having the right tools and having enough space to put the new part in. The part was only 70 dollars and I was so proud that I could do it. I am not very handy so if I can do it then anyone can. Plus I saved some money!

Washer would not drain nor spin

  • Customer: Tracy from Danville CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
My husband read on the Internet how common this problem is and how easy we could do it ourselves rather than pay the service etc.... While reading there was a link for Part Select. We simply found the part with-in minutes and ordered. They have PayPal so I basically ordered it in less than 1 minute, emailed my receipt and DONE! We selected overnight shipping because the laundry was piling up - we received the part less than 24 hours and I was up and running before dark! PERFECT!

Odd noise when the spin cycle started, water would not drain, D5 error.

  • Customer: Anthony from Holbrook AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The washer comes up with the D5 error if either the door is not shut correctly, or it can not detect that the washer is drained. I had to put the washing machine on its side to access the bottom. There is an access hole that you can get the pump from. I unplugged the pump, then removed the bolts to take it out. The pump comes apart with a few screws removed. I saw that the magnet inside was broken in half. Putting a new pump back in solved the issue.

drain pump runs continuously

  • Customer: Joe from Greenfield MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Checked owners manual for diagnostics. Pointed to door lock mechanism, so we replaced. didnt work. Went online to Just Answers.com, chatted with pro named Mike(for the fee of $25) and without getting full description, he told me to replace pressure sensor. Bought one here for $50, replaced it, and still the problem lingered. Called a real Technician to the house, for $90, and he spent 4 minutes looking and tapping, and voilla, it worked. Turns out it was a stuck relay on the control board, and the tapping loosened it. He told me I may have trouble with it in the future. If so, I would buy one here. Thanks

I was getting an "nd" error code with every wash cycle.

  • Customer: Timothy from Bismarck ND
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the back service panel and checked the drain hose for any debris and checked the connection from the tub basin to the drain pump. I then check the drain pump and noticed the impeller blades were a bit worn. After the new drain pump arrived, I did have to swap the old intake housing with the new one in order for the whole thing to mount to the shock-absorbing mounting plate. Reconnected both hoses and the electrical connection and everything ran great!

Hot water would not shut off when wash temperature selected was hot or warm.

  • Customer: William from Charleston SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power cord. Shut off water supply. Disconnected hot water supply hose. Removed top cover. Disconnected appliance connection to Hot Water Control Valve. Removed screws holding HWC valve. Removed existing HWC valve. Installed new HWC valve. Reconnected appliance connection. Reconnected water supply hose. Turned on water to check for leaks. Reconnected power supply. Started washer with hot cycle selected. Timed water fill time. Replaced top cover. Washed a load of whites in hot water. Installation and test complete.

it does not do anything. It does not work at all.

  • Customer: Ricardo from Rockwell NC
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the part.

outer door was broken at hinge due to someone leaning on it when it was open

  • Customer: shawn from manistique MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I started by watching the repair video on the site. Only tools needed were a phillips head screwdriver and a standard screwdriver. had the whole thing done and operational in about 15 minutes

installing new door latch

  • Customer: Andrea from Rochester MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
first of all, I am not at all handy, so that fact that I could do this at all is pretty amazing. I watched the video and it was very good. At first all went smoothly...I got the top off, the control panel off and the detergent drawer out. Then I ran into problems, three of the six screws holding on the front panel wouldn't come out. I sprayed Liquid Wrench on, waited for a while, still wouldn't come off, then I tapped them with a hammer, still wouldn't unscrew. But I was able to access the door latch from the top rather than the side...a little tight and awkward, some swearing was required, but it worked. Machine now working like a charm, yay!

Water pump broke

  • Customer: Kermit from Laplace LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Remove back panel disconnect hoses clamps with hands, use socket wrench on hex bolts, remove pump use philip screw driver. Install new pump same tools, replace panel stated washer, works like new.

Door lever was broken

  • Customer: Wayne from Metairie LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Used online video which was really good. After changing the lever, I realized I needed to order a new latch because it was broken also.
All Instructions for the MAH6700AWW
61-73 of 73