MAH55FLBWW Maytag Washer - Instructions

I followed the instruction of using a tie strap to secure belt to drive pulley and turn pulley to place belt on pulley. Worked great. Done in no time.

Working from back of machine, slip old belt off drum pulley. Loosen 1/2" nut to remove drive motor from outer drum assembly. Work motor toward front of machine, while holding carefully, to slip out of old isolators. Remove worn isolators. Replace with new isolators (lip towards front of machine). Re-install motor with the nut/washer all the way up against the stop for the least amount of pressure possible on belt tension..tighten bolt. (Believe me.. when you try to install the belt, it will still seem like the belt is not the right size and way too tight.).. It is, however, the correct belt.
Have a zip-tie ready.
Engage the new belt on the motor shaft pulley. The belt grooves should line up with the motor shaft grooves towards the end of the shaft. Grip the drum pulley and rotate counterclockwise while guiding the belt onto the pulley. At about 12 O'Clock, zip-tie the belt to the pulley.. then rotate ccw until installed.. (about 6 O'Clock). Snip off the zip-tie and your ready to go.

Followed a video

Pretty straight forward. After disconnecting the power. Remove the back panel, locate the drain pump. Disconnect the hoses [some water will still be in the hoses, have towels and dry vac ready] Remove protective plastic from the top of the pump and remove the electrical connection reassembled with new drain pump.

The replacement of the drain pump was very easy. I will not go into detail, just follow the video installation provided on this site and you will have no problem.

I decided to replace the drive belt since I was into the back of the washer. The video on this site was spot on, however I did have to apply a lot of effort putting the new one on. My old belt was stretched out considerably and at first thought I had a wrong replacement belt. Number on the belts confirmed it was correct. Just had to walk the belt on the larger pulley and it will fit.

My washer is running like a new one!

Unplugged, turned water off, removed hoses. Removed screws, unplugged wires, disconnected interior hose and replaced old water inlet valve with new one. Reassembled. Repair was completed by my 17 yr old son in 20 minutes.

We followed the directions in other people's repair stories here. Removing the spring was a challenge, as was getting it back on! The rest of the repair was simple. Be patient with removing the soap dispenser. Ours had some plastic cords connecting it to the frame which we didn't anticipate, and we broke them because we didn't see them.

We're going to try that new Affresh product in the hopes of avoiding this repair again in the future. We never washed anything harmful in the washer. This seal becomes moldy and deteriorates with time. Using bleach to kill the mold only speeds the process.

Removed outer door and positioned it on counter next to new part.
Transitioned each part element from from one to the other.
Finally re-install door back in place..........

I followed the steps on the first post which are very good. I had trouble, however, putting the seal over the drum. I finally removed the plastic rim to the drum by removing the clips. I was then able to lay the rim on the floor and put the new seal over it more easily. It is a lot like putting a bicycle tire on a rim. I had no helpers so I used a vice grip pliers on one end of the cable-spring and another pliers on the other. I was then able to pull both ends together enough to get them to hook up. I recommend removing the plastic rim as I mention above. Had I done this first, I would have done the job in less than 30 minutes.

Removed four screws, removed original bezel. Replaced with new bezel and then replaced 4 existing screws.

Removed and replaced old shroud with new one. Works great.

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

Unscrew door hinges, front panel, soap tray, lift top to 12 oclock position,unhook strap from spring located on top of the drum,tape strap ends to drum to prevent from falling,disconnect the billows drain clamp on the bottom of the billows,remove the billows by peeling off the drum, install the new billows from the top first and tape it to the drum to prevent it from slipping off as you work your way around the drum,install the strap in its track, secure with spring(better with two people)in same location, hook up billow drain, finish doing the laundry.

replaced inside of door

I looked on Utube at some videos which helped a lot all told i replaced the bearings in the outer hub which was quite a chore as the bearings came out rather hard I used a steel rod about 18 inches long and a heavy hammer to pound the old bearings out they came out hard then I put the new bearings in very carefully as I had to tap them back into place and installed the seal and put the new shaft on the tub and slid everything back into place. The instructions that came with the new seal and shaft were very helpful I bought the new bearings from local implement dealer as they were not available with the shaft and seal didn't keep track of my hours probably about 21/2 to 3 hours