Models > MAH3000AWW > Instructions

MAH3000AWW Maytag Washer - Instructions

All installation instructions for MAH3000AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MAH3000AWW
76-90 of 212
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washing machine wouldn't drain water or finish load

  • Customer: Cheryl from Palmer AK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Even though after reading many repair blogs saying not to remove the back of the washer, I did anyway. Lo and behold after opening it, the pump was right there!! I removed the hoses (make sure you have a bucket, or shop vac handy) lots of water will come pouring out use your bucket for this, I used my shopvac to suck the rest of the water out of the hose, and bing, the washing maching door opened and allowed my to retrieve my clothing(stinky now after the washing machine held them hostage for days) I removed it by removing 3 bolts, and 1 screw very easy. I took apart the pump to see if there was anything blocking up the moter there was nothing, but the plastic pump blade was chewed up so bad, it no longer would turn to pump out the water. I had to order a pump. When my pump came in 2 short days later, I reversed to removal process and presto!! The washing machine was running like new.

Washer would not emtpy the water from the tub

  • Customer: Margaret from Fowlerville MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I removed the back panel and located on the left side of the washer removed the pump and replaced it.

Water not emptying out

  • Customer: Rita from Three Rivers MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Removed back of washer and unscrewed pump band and hose removed pump and replaced pump,replaced hose to new pump,WE really appreciated the fast shipping of the part from your facility.Thank You again

Replace power cord that had burned from a small fire

  • Customer: Hersch from Mamaroneck NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
I removed top control panel and then the old power cord that been damaged by a small fire and the just attached the new power cord and control panel. Unblievably simple and I saved myself a lot of money. Where I live in a NYC suburb this type of simple repair could easily cost $100.

leaking water at the seal between the drum and door assembly

  • Customer: max from antioch IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 4 of 10 people found this instruction helpful
I took the door off, front panel, soap dispenser(to lift the top out of the way)and took off the cross braces on the front of the machine. I pealed the door bellows off and took the drain hose apart; there was much gunk and debris to clean out...maybe something here was clogged? Removed all the snap clips and took the front of the tub off;the tub seal seemed good, but lots of grime/gunk build up.I cleaned all surfaces, put the new tub seal on,and put it all back togther. The hardest part was working the snap clips back on; I worked a few on both sides, top and bottom, and then filled in the rest. The machine has been working fine for a month now, no leaks:)

motor not working

  • Customer: CECILE from BROOKLYN NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 14 of 41 people found this instruction helpful
followed the diagnostics instruction in the Maytag Owners booklet which pointed to the Motor Control Assembly.
PartSelect was a very good choice for securing the part.

Bad tube seals and bearings

  • Customer: DAVID from SANDY HOOK CT
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Socket set, Wrench set
  • 1 of 1 people found this instruction helpful
Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

Dispenser lid plastic around metal pins that insert into washer broke so it fell off everytime I opened to add soap etc

  • Customer: Margaret from Burleson TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 1 of 1 people found this instruction helpful
I got the part, but it did not come with the pins needed to insert into slot in washer. I had to go to Lowes and buy some pins and improvise to make them fit on both ends. It is working well....Probably saved myself $100.00 (service call etc) Thanks

Flanges on the bezel had broken (poor design).

  • Customer: Patricia E. from Roselle NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed old screws and bezel.
replaced new bezel and screws.

The exoloded views and drawings were a great help.. Thanks for being there with views and the right parts that fit perfectly.. Love the service.. Patty O'

Torn and moldy boot seal

  • Customer: Brenda from EL Paso TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 1 of 1 people found this instruction helpful
We followed the directions in other people's repair stories here. Removing the spring was a challenge, as was getting it back on! The rest of the repair was simple. Be patient with removing the soap dispenser. Ours had some plastic cords connecting it to the frame which we didn't anticipate, and we broke them because we didn't see them.

We're going to try that new Affresh product in the hopes of avoiding this repair again in the future. We never washed anything harmful in the washer. This seal becomes moldy and deteriorates with time. Using bleach to kill the mold only speeds the process.

Replace Timer Knob

  • Customer: Jose R. from Orlando FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
It was easy as 1,2,3. Took the old knob apart and replaced it with new one. About 20 minutes.

Dispenser Bezel broked in two places

  • Customer: Neal from Jefferson City MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I visited several web sites looking for repair parts for my Maytag washing machine. Your site was the easiest to navigate and provided great diagrams and pictures to ensure that I purchased the correct part. I liked the ability to track the delivery of my parts via your web site. I received my parts within a couple days.

leaking water

  • Customer: richard from amston CT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 2 of 5 people found this instruction helpful
removed one panel and front door to access under tub.leak solved!!!! thanks

Boot torn on frontload Maytay Neptune Washing Machine

  • Customer: Jon from Bozeman MT
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 1 of 2 people found this instruction helpful
With a torn boot on this front load washer, (nails in the pocket of my jeans) water leaked out on the floor with every wash. I knew it would cost a fortune to get fixed, so I decided to try it myself. I can take anything apart!
I heard of Parts Select.com from a friend and checked it out. With their help, I found the model and part and just ordered it. It was easy!
When the part arrived, I was obligated then to do something!
Since this is a stack unit, with the dryer on top, I thought I would take the dryer off and try the repair from the top. But there was no way that dryer was coming off! I tryed every screw and it wouldnt budge.
So I saw two screws in the front and started in on the washer below. I was careful to make notes on how I took this machine apart so I could put it back together!
I got down to the drum with a spring close guywire that holds the boot tight to the drum. It came off easily and I took the old torn boot off and put the new boot in place.
The tough part was getting that guywire and tight spring back on! The lip that holds the boot to the drum is very shallow and the book would not stay on all the way around and allow me to string the guy wire around in the little channel without coming off. FRUSTRATING!
I improvised and used duct tape to tape the boot to the drum to keep it in place so I could string that wire around. Man, did that take some doing!
I managed to get that wire around with the help of the duct tape, but the second big challenge was putting the spring on, as it was under alot of tension. It was tough to puuuuuullllll it together without pulling the boot out of the channel I had to duct tape it into!
By the grace of the Almighty, some prayer and some cussing (forgive me Lord), I got the spring into the rings on both ends of the guy wire. VICTORY!
Putting the boot front back in is easy, just put it into the holes that receive the projections under the front of the boot. No problem.
After all that, putting the washer all back together was a cinch!
And....
IT WORKS!!
I did it! No more leak! No expensive fix it job!
I did it myself, am prouder than heck!
Oh.....
No more Nails in the jean pockets!

Dispenser Bezel became brittle, so that screws would not hold anymore.

  • Customer: Ralph from Hampstead NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Unscrewed the 4 screws of the old bezel; lifted the bezel out; moved the lid from the old bezel to the new one; set bezel in place and screwed it in with the old screws. Looks and feels like new.
All Instructions for the MAH3000AWW
76-90 of 212