Models > MAH2400AWW > Instructions

MAH2400AWW Maytag Washer - Instructions

All installation instructions for MAH2400AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MAH2400AWW
16-19 of 19
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door diaphragm (rubber piece) was moldy and needed replacement.

  • Customer: David from Washington DC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Unplug washing machine. 2. Removed front cover at base on washing machine. 3. Removed three front screws under the cover. 4. Removed one screw on right side top. 5. Removed detergent dispenser and screws beneath. 6. Removed top of washing machine by removing two screws in back. 7. Removed clasp on front of diaphragm. 8. Removed door. 9. Removed clasp on back of door by unscrewed. 10. Replaced diaphragm. 11. Put everything back together in reverse order.

washer would make a grinding sound and would not drain

  • Customer: marshall from chemung NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
found a quarter in the drain pump.it destroyed the impeller. hardest part was to get the water out to move it . i added a pvc pipe drain screen and modified the holes hoping it wont plug with lint. other wise great service an easy repair. thank you.

Water Pump Digital Read Out "ND" No Drain

  • Customer: chris from Brooklyn NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This particular model does not have a drain filter that keeps pennies and bobby pins from getting in the rotor of the pump. Make sure you turn off machine and unplug from wall electrical, wait 10 minutes and then open door. Tilt machine back at angle to prevent water from coming out of the front door. Use a cup to scoop out excess water from drum. The pump is under the right front corner of machine, so you can turn machine on left side after hand scooping water out. Remove two spring hose clamps with fingers and electrical connectors. four screws hold pump mounting bracket to body of machine. Remove those and while you have the machine on its side. Go ahead and take hose off that leads to drain in wall. Use coat hanger to make sure it is free from debris. You can take three screws out that holds pump together and get to any of the pins, pennies, etc that are inside the pump. Re-assemble....presto. When you plug machine back in, wait for a minute and then put on spin cycle, not drain. The sensor for draining thinks machine is empty. Put a machine cleaning product through once for a short wash cycle and then you can use machine again normally.

Hot water would not shut off when wash temperature selected was hot or warm.

  • Customer: William from Charleston SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power cord. Shut off water supply. Disconnected hot water supply hose. Removed top cover. Disconnected appliance connection to Hot Water Control Valve. Removed screws holding HWC valve. Removed existing HWC valve. Installed new HWC valve. Reconnected appliance connection. Reconnected water supply hose. Turned on water to check for leaks. Reconnected power supply. Started washer with hot cycle selected. Timed water fill time. Replaced top cover. Washed a load of whites in hot water. Installation and test complete.
All Instructions for the MAH2400AWW
16-19 of 19