Models > MAH2400AWW > Instructions

MAH2400AWW Maytag Washer - Instructions

All installation instructions for MAH2400AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MAH2400AWW
1-15 of 19
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer wouldn't spin / drain

  • Customer: Sarah from Kirkland WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 25 of 30 people found this instruction helpful
First I looked up the error codes in the washing machine technical information pamphlet I got when buying the machine to determine what the problem was. It indicated that the machine wouldn't spin. After doing a few more tests I couldn't find the error code that was displaying, but the machine wouldn't run at all and just did a terrible growling sound. I tilted the machine back to get access to the bottom. Undid the flimsy corregated covering held in by 4 screws. In the right front corner I found the pump. There were 2 tubs connected to the pump; I undid each (a simple squeeze off holder) and found nothing blocking either passage. The type of pump is build as one part, so I was unable to open it up.
I decided to order a new pump assuming that was the problem and in fact it was. Replacing the pump was a piece of case. I undid the two tubes, disconnected the electrical connector then removed it from the washer casing with 4 screws. The new pump was easy to install -- screwed it in place with the 4 screws, reconnect the electrical part (just a simple female / male connection), reconnect the 2 tubs, put the bottom covering back on, and that was it. It's working just fine now.

Coin ruined drain pum impeller blade / SUDS error

  • Customer: Dan from Arlington VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 19 of 21 people found this instruction helpful
Unplug machine, turn on its side (have bucket to drain water from hose), unscrew drain hose bracket on back (so you can fully empty water still inside machine) unscrew bottom plastic cover, locate pump on left, pull out electrical connector, unscrew hose clamps, twist off hoses, unscrew pump and replace, and follow the above steps in reverse. I also made a coin trap from a sawed off plastic drain or downspout cover/protector and installed this inside the hose at the entry point to the pump, enlarging the holes enough to make sure they wouldn't easily clog with lint.

I leaned on the door while open and it broke off!!

  • Customer: Raymond from Fort Myers FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 28 people found this instruction helpful
Removed hinge and all screws holding two halves together with glass between them put glass in new parts and replaced all screws hinge fits in there also
installed back on washer and away we went....

washer did not complete the cycle due to bad pump

  • Customer: judy from aspen CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
I turned the washer on its side disconnected the hoses attached to pump. Then unscrewed the pump attatched to the washer base; undid the power source and ordered the part from you.
Reattached the new pump to the washer: reconnected the power source and hoses to the new pump. Then flipped the washer upright and it works.

A quarter was lodged in the drain pump and demolished the impeller.

  • Customer: Tosca from Mundelein IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
After two weeks with out a Washing machine in the RV, we were finally in a place long enough to order the part to fix it. I replaced this part before through Sears and although the price was similar,'it took two weeks to deliver the part. This was here the next day. One screw, two clamps and it was done.

Wouldn't spin or drain properly, suds error.

  • Customer: Christine from Dysart IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
Since this was our 3rd time to remove this part, due to coins getting stuck in the pump, it went pretty easily. Removed the panel underneath, removed and replaced the pump, replaced everything as it was. Washer works great again!

clinking noise as machine was trying to drain

  • Customer: mildred from castle hayne NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
got on internet found website that would show me how to get to the pump, part select phone number and the part number of drain pump- ordered on thurs night, got part on sat.am, me and my roommate tilted machine removed the 4 screws and 2 pipe clamps, did reverse procedure and machine was fixed- total repair cost was less than a service call

Water leak from draw assy

  • Customer: Dennis from Oxnard CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Undo screws two at the back, take the lid off disconect the pipes to the assy,a little tight for room if you have larger hands.Pipes have spring clamps. Undo screws holding the aasy, in front behind trim and screws at the top.This is the 5th time I have replaced this part the water lines clog up so there for water runs all over.

Main sping wore through Spring support bracket

  • Customer: Paul from Green Bay, WI WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
In this model the 2 main springs hang from a bracket built into the top of the machines frame. For some reason one of the pring was installed without the protective plastic grommet (called the guide spring washer). The handened spring eventually wore through the softer metal bracket due to the vibration of the washer.
The purchsed plastic part fit into the bracket so firlmy that even with part of the bracket wore away it appears to be still strong wnough to support the weight of the tub. It has made it through 10 loads so far and it still working well.
Getting at the spring was easy but lifting the tub was heavy. Thanks - $4 part saved a $1000 washer.

Cold water valve not operating

  • Customer: Chris from Tyler TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 3 of 9 people found this instruction helpful
Simple 2x cross head screws remove water inlet pipe, 2 internal pipes with spring clips, 2 electrical connectors test for leaks and operation perfect

Push buttons broken, missing start button

  • Customer: Sallie from Yuma AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 5 people found this instruction helpful
Took top off & disconnected each connection on the old control board assembly. Attached new one
to wiring. put top back on. Connected to water &
wash 1st load that night.

washer stoped working

  • Customer: Doris from Houston TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 4 people found this instruction helpful
open up the back and listen to the noise then I fixed the problem I me Kevin Isadore the good job. thanks

door cover broke when opening the door and panel draw broke...somehow

  • Customer: Carlotta from New Orleans LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 17 people found this instruction helpful
panel drawer cover required only one screw and the door cover had 8 screws to deal with but was really simple. Love the site!

The boot around the door had a whole in it. The water was comming out of the hole and on to the floor. So we had to shut off the whasher an dtak ethe clothes hom efor over a month. The part we needed was back ordered. Our father in law turned the boot around the other way so the hole was on the bott

  • Customer: Justine from So Dennis MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 29 of 120 people found this instruction helpful
I dont know exactly what he used to put it back. I think it is pretty easy to do. You need to make sure that everything lines up properly.

Would not drain

  • Customer: Thomas from Baytown TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I have a front load washer, from the front of washer, down to the bottom pull off the cap, unscrew drain pump. Very easy to pull out. Also very easy to replace, I give this product a 5 star.
All Instructions for the MAH2400AWW
1-15 of 19