Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LWD70AW > Parts

LWD70AW (PLWD70AW) Amana Washer - Parts

All parts for the Amana Washer LWD70AW

Below is a list of all parts for the Amana Washer LWD70AW - Top Loading. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the LWD70AW
1-14 of 222
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.02

Screw

This screw is sold individually.

$4.63

Washer, Thrust

This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found on dryers around the drum support rollers and idler pulleys, and helps prevent the rollers and pulleys from bumping up against the brackets they are installed on. Your thrust washer could be defective if you notice your dryer wont tumble, rotate, or turn; or there is a load squealing or whining noise when the dryer tumbles. The repair is a relatively easy job. You will require a putty knife, 5/16 inch nut driver, and E-Ring pliers. Remember to disconnect the power to your dryer before you begin the repair.

$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

$7.86

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Your washer should be kept as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This genuine OEM replacement part is sold individually, so be sure to order the amount you need.

$7.00

Retaining Ring

The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has s...

$3.02

Lid Hinge Mounting Screw

Sold individually.

$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washe...

$23.65

Drain Hose with Rubber Elbow

This hose attaches to the pump to help remove the water out of the washer.

$22.43

Idler Pulley Wheel

This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$2.96

Screw

Sold Individually.

$30.11

V-Style Spin and Agitate Belt - 28-3/4 inches long

This v-style spin and agitate belt is 28-3/4 inches long and half of an inch wide. It is all black in color and made entirely of rubber.

$14.42

Idler Pulley Shaft

This shaft is made to fit the center of the idler pulley wheel of many clothes dryers. It is less than two inches long, and is made of metal.

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$4.48

Inlet Hose Washer

This high-pressure inlet hose washer, or gasket, is used with many washing machines, refrigerators, and dishwashers to create a watertight or airtight seal in the appliance. It is black in color, made of rubber, and about 1 inch in diameter. Rubber gaskets can get dry and brittle over time, causing them to lose their integrity and malfunction or crack, which will compromise the seal. It is recommended to check other seals before ordering this part in case they also need to be replaced. This is an OEM part sourced directly from the genuine manufacturer.

All Parts for the LWD70AW
1-14 of 222