Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LWC75AW

LWC75AW (PLWC75AW) Amana Washer - Overview

Get Parts and Repair Help for LWC75AW

If you know the washer repair part you need, you can browse the list of all parts on the LWC75AW, or you can search by name or part description. You can also find your part by where it is located on the LWC75AW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LWC75AW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.35

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Drain Pump

This pump is attached to the motor and helps expel water from the washing machine. It is activated after the spin speed is maintained for a specific period of time.

$63.50

Water Inlet Valve Kit

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount o...

$27.04

Brake Pad Kit

This brake pad kit contains three brake pads and six installation screws. Helps to bring a rotating cycle to a stop.

$24.97

Inlet Hose Kit

This hose is almost 5 feet long and now comes with the washers for proper installation. It is used to bring water into your washer for the cycles.

$19.22

Standpipe Adapter

This part helps stop the washer from overflowing.

$55.15

Flex Vane Agitator

This white agitator is used for belt driven washing machines.

Plastic Washer

This washer is located between the brake and transmission drive pulley.

$28.58

Friction Ring

$7.93

Screw

Sold individually. 1/4-20

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking on floor from "mysterious place underneath washer"

  • Customer: Bryan from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 37 of 42 people found this instruction helpful
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

read more

The Seal On The Bottom Of The Tub Was Leaking

  • Customer: HOWARD from CORTLAND, OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 30 of 38 people found this instruction helpful
Removed the front of the washer, then lifted the top up and held it up with a prop. Pulled the agitator straight up and started the disasembly. Using the photos in the hub and seal kit was a big help. The large nut on the output shaft had to be cut off with my dremel tool and the hub removed with a wheeler puller. Assembly was pretty much straight forwar... read more

Bad shaking During Spin Cycle

  • Customer: Gary from Park Ridge, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 31 of 48 people found this instruction helpful
firsted layed washer back On A Angle For Easy Acess To Motor Removed Both Hoses And Four bolts pulled Motor Assembly out replced belt @ idler Pulley Reinstalled Motor. read more