Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LWC50AW

LWC50AW (PLWC50AW) Amana Washer - Overview

Get Parts and Repair Help for LWC50AW

If you know the washer repair part you need, you can browse the list of all parts on the LWC50AW, or you can search by name or part description. You can also find your part by where it is located on the LWC50AW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LWC50AW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.35

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Order within the next 11 hrs and your part ships today!

Drain Pump

This pump is attached to the motor and helps expel water from the washing machine. It is activated after the spin speed is maintained for a specific period of time.

$63.50

Water Inlet Valve Kit

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount o...

Order within the next 11 hrs and your part ships today!
$27.04

Brake Pad Kit

This brake pad kit contains three brake pads and six installation screws. Helps to bring a rotating cycle to a stop.

Order within the next 11 hrs and your part ships today!
$24.97

Inlet Hose Kit

This hose is almost 5 feet long and now comes with the washers for proper installation. It is used to bring water into your washer for the cycles.

Order within the next 11 hrs and your part ships today!
$19.22

Standpipe Adapter

This part helps stop the washer from overflowing.

Order within the next 11 hrs and your part ships today!
$55.15

Flex Vane Agitator

This white agitator is used for belt driven washing machines.

Order within the next 11 hrs and your part ships today!

Plastic Washer

This washer is located between the brake and transmission drive pulley.

$28.58

Friction Ring

Order within the next 11 hrs and your part ships today!
$7.93

Screw

Sold individually. 1/4-20

Order within the next 11 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Belt wore out

  • Customer: Bruce from Medina, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 163 of 187 people found this instruction helpful
Had to remove pump-not easy. Nothing wrong with pump, but had to trash it to get it off the motor shaft, so I had to replace it, too.

Pop up top of cabinet and remove front panel. (I leaned unit back against a wall to facilitate internal access once panel was removed.)


Remove motor assy - 4 screws & connector.

Remove ... read more

Noisy during spin cycle

  • Customer: Gary from Dousman, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 77 of 83 people found this instruction helpful
This was the second time for the repair. The original bearing lasted 5 years then became noisy. Replaced it, and the unit worked great 5 more years and the noise came back. So I knew exactly what needed fixing what to order, parts wise. This is not a project for the faint of heart, you will completely disassemble your washer to change out the main bearin... read more

Drive Pump Leaked

  • Customer: Stephen from Laveen, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 66 of 78 people found this instruction helpful
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screw... read more