Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LWA80AW

LWA80AW (PLWA80AW) Amana Washer - Overview

Get Parts and Repair Help for LWA80AW

If you know the washer repair part you need, you can browse the list of all parts on the LWA80AW, or you can search by name or part description. You can also find your part by where it is located on the LWA80AW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LWA80AW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.02

Screw

This screw is sold individually.

Order within the next 8 hrs and your part ships today!
$4.63

Washer, Thrust

This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found on dryers around the drum support rollers and idler pulleys, and helps prevent the rollers and pulleys from bumping up against the brackets they are installed on. Your thrust washer could be defective if you notice your dryer wont tumble, rotate, or turn; or there is a load squealing or whining noise when the dryer tumbles. The repair is a relatively easy job. You will require a putty knife, 5/16 inch nut driver, and E-Ring pliers. Remember to disconnect the power to your dryer before you begin the repair.

Order within the next 8 hrs and your part ships today!
$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

Order within the next 8 hrs and your part ships today!
$7.86

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Your washer should be kept as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This genuine OEM replacement part is sold individually, so be sure to order the amount you need.

Order within the next 8 hrs and your part ships today!
$7.00

Retaining Ring

The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has s...

Order within the next 8 hrs and your part ships today!
$3.02

Lid Hinge Mounting Screw

Sold individually.

Order within the next 8 hrs and your part ships today!
$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washe...

Order within the next 8 hrs and your part ships today!
$23.65

Drain Hose with Rubber Elbow

This hose attaches to the pump to help remove the water out of the washer.

Order within the next 8 hrs and your part ships today!
$22.43

Idler Pulley Wheel

This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Order within the next 8 hrs and your part ships today!
$2.96

Screw

Sold Individually.

Order within the next 8 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking on floor from "mysterious place underneath washer"

  • Customer: Bryan from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 42 of 47 people found this instruction helpful
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

read more

The Seal On The Bottom Of The Tub Was Leaking

  • Customer: HOWARD from CORTLAND, OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 30 of 38 people found this instruction helpful
Removed the front of the washer, then lifted the top up and held it up with a prop. Pulled the agitator straight up and started the disasembly. Using the photos in the hub and seal kit was a big help. The large nut on the output shaft had to be cut off with my dremel tool and the hub removed with a wheeler puller. Assembly was pretty much straight forwar... read more

Bad shaking During Spin Cycle

  • Customer: Gary from Park Ridge, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 32 of 49 people found this instruction helpful
firsted layed washer back On A Angle For Easy Acess To Motor Removed Both Hoses And Four bolts pulled Motor Assembly out replced belt @ idler Pulley Reinstalled Motor. read more