Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LW8463L2 (PLW8463L2)

LW8463L2 Amana Washer - Overview

Parts and Repair Help for models starting with LW8463L2

If you know the washer repair part you need, you can browse the list of all parts for models starting with LW8463L2, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LW8463L2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with LW8463L2

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$5.15

Washer, Thrust

This washer is 3/4 inches in diameter.

$5.15

Screw

This screw is sold individually.

$5.15

Hose Clamp

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$5.51

Hose Clamp

This hose clamp is sold individually.

$21.40

Drain Hose with Rubber Elbow

This hose attaches to the pump to help remove the water out of the washer.

$16.82

V-Style Drive Belt (32.5 inches long)

This v-style drive belt is thirty-two and a half inches long and half of an inch wide.

$10.35

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

$10.11

Retaining Ring

This metal retaining ring is well under an inch long. Use it for your Maytag brand clothes washer or your clothes dryer.

$5.15

Lid Hinge Mounting Screw

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Frayed V-belt

  • Customer: John from Milton, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 47 of 53 people found this instruction helpful
VERY EASY!!!
SAFETY FIRST-Always unplug the appliance.
Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, remove 4 mounting bra... read more

Water leaking on floor from "mysterious place underneath washer"

  • Customer: Bryan from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 40 of 45 people found this instruction helpful
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

read more

The Seal On The Bottom Of The Tub Was Leaking

  • Customer: HOWARD from CORTLAND, OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 30 of 38 people found this instruction helpful
Removed the front of the washer, then lifted the top up and held it up with a prop. Pulled the agitator straight up and started the disasembly. Using the photos in the hub and seal kit was a big help. The large nut on the output shaft had to be cut off with my dremel tool and the hub removed with a wheeler puller. Assembly was pretty much straight forwar... read more