Models > LW7503W2 (PLW7503W2 A) > Instructions

LW7503W2 (PLW7503W2 A) Amana Washer - Instructions

All installation instructions for LW7503W2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LW7503W2
61-75 of 115
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Leaky drain hose

  • Customer: Keith from Little Elm TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
First I tried to lift the lid on the top of the washing machine. I eventually realized this model doesn't open up from the top. I removed two screws on the very bottom of the front panel of the washing machine. Then pulled gently downward to release the front panel from the two clips holding it in at the top. Once the front panle was removed, I found I could easily access the drain hose and disconnect it from the pump by loosening the clamp screw. (Be aware, there is still water in the hose and pump that will run out onto the floor; I had a bucket close by and tried to catch most of this water, but its somewhat futile.) There are two additional hose clips one underneath the tub, and one on the back panel of the washer that hold the hose away from other mechanical parts. Once the hose is freed from those clips it could be removed from the washer by feeding the hose out the back panel. The new hose was then inserted and fed down inside the washer, attached to the pump, tighten the hose clamp screw, clip the hose to the other two clamps so it is out of the way of other parts, reattached the front panel and you're done!

One other note about PartSelect.com...A few days after ordering my part, I had an "International Transaction Fee" show up on my debit card statement. I panicked thinking my card number had been stolen only to call my bank and find out PartSelect is based in Canada.

I had no standpipe adapter and water was overflowing

  • Customer: mary ann from edison NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I figured that the best thing to do is buy an adapter for the standpipe and now no more overflowing.

Drain hose sprung a leak

  • Customer: Burton from Sutton MA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
simple as removing front panel from washer held on by two screws and the hose was right their. Took a few minutes to disconnect it from the pump and pull it out through the rear, then feed the replacement in and reverse the process. Piece of cake. Thank you.

TIMER WAS NOT ENGAGE TO TURN WASHER ON TO WASH SyCLE

  • Customer: theo from flemington NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
took the timer nub off by unscrewing then the cover housing the timer unit .6 screws .3 in front 3 in back .
cover came off easy.un plug the power. disconect old timer and replace with the new .plug comes off easy by gently puling it out .
put back cover put back timer nub plug the power on and there it was back as new.

Wouldn't pump out water

  • Customer: Jacob from Clarkston MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 1 of 2 people found this instruction helpful
I found about 2-3 baby socks stuck in the pump and couldnt remove them so I had to replace the part. Unfortunately I found this website AFTER I took the bad pump off. So I ended up removing the lower front panel and then flipping the washer upside down and removing the bottom of the washer and taking the pump off because I couldnt see any other way to get it off. The new pump arrived very quickly and I put it back on and put the bottom panel back on and flipped the washer back right side up. I certainly made it more difficult then it had to be but it was still fairly easy. Now I see all I needed to do was remove the motor to get the pump off. Oh well.

Washer pump was leaking water

  • Customer: Lizandra from Roxbury MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 1 of 2 people found this instruction helpful
Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!

Timer wouldn't stop at the end of a cycle.

  • Customer: Daniel P from Darien IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
Pulled the electrical plug. Unscrewed the control know (counter clockwise). Gently pried off the round plastic plate under the control knob. Took off the outside cover. (2 screws). Took off the inside cover (3 screws). Disconnected the wiring harness from the timer. Unscrewed the 2 holding the timer in place. Replaced in opposite order. Connected timer, connect wiring harness, Attached inside cover, attached outside cover. Pushed in round plastic plate (make sure you line up the notches) screwed on the control knob.

Timer worn out. Wouldn't cycle properly.

  • Customer: Robert from Mobile AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
Removed the screws that held the top console which housed the timer. (5 minutes)

Laid the console over. Just rocked it forward.

Removed the 2 screws holding the timer in place.

Unplugged the wireing harness from the old timer.

Plugged the wiring harness into the new timer.

Replaced the timer and re-screwed it in place. Pulled the top console back up and re-screwed all the screws. Pushed the washer back in place and turned it on. It worked fine.

Took maybe 20 minutes.

Slow fill on cold cycles.

  • Customer: Leonard from Glen Allen VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 2 of 5 people found this instruction helpful
The repair was easy. It took approximately 30 minutes.

Washing Machine was leaking.

  • Customer: Luis from Homestead FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
First, I removed the screws, then removed the pump. I, then, installed a new pump.

washing machine pump repair

  • Customer: Walter from Euless TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 3 of 9 people found this instruction helpful
I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.

We misplaced the fabric softener dispenser.

  • Customer: Larry from Adrian MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
We promptly received the part and easily installed it with no tools. We had an excellent experience. We found the old fabric softener dispenser after installing the new one. Now, we have two.

Blanket jambed drum, belt kept turning burned belt and pump

  • Customer: John from Loganville GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 1 people found this instruction helpful
Unpluged washer, turned off water supply, removed front covers, removed spring on right side to allow drum to lean over, removed the 2 hoses from pump, removed motor (4 bolts), removed 3 screws holding pump. Installed a new belt and replaced the pump. I replaced the hoses on the pump, replaced the spring, and turned on the water, plugged in the washer, turned it on and hoped for the best. Worked fine, no leaks or problems.

belt wore out

  • Customer: Jim from Augusta WV
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
replaced belt that was wore out. decided to replace pump while I had washer apart.

Pump Leaking

  • Customer: Jeffry from Rancho Cucamonga CA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
I seemed to have a more difficult time changing the pump out than others who had left their instructions on line prior to me.
What I has to do is remove the 4 bolts that secured the motor & mount to the frame. I then unplugged the wire harness from the motor leads.
I removed the belt tensioning spring & removed the belt.
I then removed the motor, motor mount and pump assembly. Turned it upside down & removed the pump. When installing the new pump you will need to remember how the belt was routed. A local parts house actually gave me a xeroxed schematic that showed me how to route it. A real life saver.
After that I turned the assembly right side up, bolted the mount into place, installed the new belt onto the large flywheel, attached the belt tension spring, plugged in the wiring harness and ran a rinse cycle. No leaks. Good as new.
Yes. It took a little longer than expected. But it was alot cheaper than having a service man do it.
All Instructions for the LW7503W2
61-75 of 115