Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LW3303L (P1118418W L)

LW3303L (P1118418W L) Amana Washer - Overview

Get Parts and Repair Help for LW3303L

If you know the washer repair part you need, you can browse the list of all parts on the LW3303L, or you can search by name or part description. You can also find your part by where it is located on the LW3303L by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LW3303L parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.35

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

$24.97

Inlet Hose Kit

This hose is almost 5 feet long and now comes with the washers for proper installation. It is used to bring water into your washer for the cycles.

$55.15

Flex Vane Agitator

This white agitator is used for belt driven washing machines.

$21.17

Brake Pad Kit

Included in this kit are three long shoulder bolts, three short boulder bolts, three brake pads, three short rubber grommets, & three long rubber grommets..

$7.93

Screw

Sold individually. 1/4-20

$4.74

Washer

This washer is located between the brake and transmission drive pulley.

Complete Hub and Seal Kit

This kit comes with hub, seal head, gasket, seal shroud, seal seat, screw, spline insert, drive bell and seal.

Drive Bell and Seal Kit

This washing machine drive bell and seal kit comes with a seal, a plug, a shoulder screw, a drive bell, and some grease.

$22.60

Siphon Break Kit

Included in this kit are the clamps for the drain hose.

$5.63

Idler Pulley Lever

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Frayed V-belt

  • Customer: John from Milton, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 46 of 52 people found this instruction helpful
VERY EASY!!!
SAFETY FIRST-Always unplug the appliance.
Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, remove 4 mounting bra... read more

The Seal On The Bottom Of The Tub Was Leaking

  • Customer: HOWARD from CORTLAND, OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 30 of 38 people found this instruction helpful
Removed the front of the washer, then lifted the top up and held it up with a prop. Pulled the agitator straight up and started the disasembly. Using the photos in the hub and seal kit was a big help. The large nut on the output shaft had to be cut off with my dremel tool and the hub removed with a wheeler puller. Assembly was pretty much straight forwar... read more

Bearing went out causing lots of noise.

  • Customer: mike from hull, IA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 20 of 22 people found this instruction helpful
This is not a bad repair, but give yourself some time. I did not have to take the tranny and motor out, but the inner and outer tub and all related parts had to come out, along with the outer tub base. If you are replacing the tub bearing, you HAVE to order the seal kit. Don't try to skimp like I did, since you will need the seal kit as this is what causes t... read more