Models > LTF6000ES1 > Instructions

LTF6000ES1 Frigidaire Washer - Instructions

All installation instructions for LTF6000ES1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LTF6000ES1
61-75 of 208
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Vane broke off inside drum

  • Customer: Glen from Redondo Beach CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 9 people found this instruction helpful
Inserted new vane into slots in the drum. I then held the front of the drum while I slid the vane tabs in place by pushing the vane to the back of the drum. Once the vane was in place, I screwed in the screw that came inside the vane kit.

washer door woild not lock and would not allow washer to operate

  • Customer: Kevin from Merrimack NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Removed top cover of washer to get to the door lock mechanism then used a phillips head screwdriver to remove door lock mechanism. I then replaced door lock mechanism with the new one I bought from PartsSelect. The repair job was very easy and took a total of 15 minutes to remove old part and install new one.

Washer wouldn't enter the spin cycle. Clothes wet at end of wash cycle.

  • Customer: Leslie from Tolland CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Open the door. Pull the clamp off of the boot (locate spring at bottom). Peel back the boot on the right side so that you can get to the door lock and switch assy. Remove the 2 screws in the front that hold in the door lock and switch assy. Remove the wires from the old assy. Transfer the wires to the new assy. Screw in the new assy. Refit the boot and clamp. give it a try.

drum pulley kept getting loose and wobbling. Hub wore out making permanent tightening impossible

  • Customer: Richard from Long Valley NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Simple. Remove the drive belt from the pulley. Next remove the retaining screw and remove the old pulley. Put the new pulley on the hub, then insert the retaining screw and tighten securely. Last, replace the belt over the motor and hub pulley. This was the most difficult part as the new belt was quite tight. But once I convinced myself it was the right belt a little more effort yielded results and the belt fit fine.

One of the wash tub shock absorbers broke.

  • Customer: Joshuah from Indianapolis IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
I heard that the repair job was simple and the part was not expensive (whew!) The repair video on your website was MOST helpful and gave me confidence. At first I tried it exactly as the guy demonstrated and all went well removing the broken support. Installing the new one (on the right side) was impossible for me. I could not get good enough leverage to fully re-insert the lock pins and I was slicing up my arm on the sharp metal edges. I removed the 900+ screws (just kidding- but there were quite a few) from the back panel and could access the lock pins MUCH easier. All four for both shock absorbers snapped right in. Re-attaching the rubber vent hose involved a few cuss words but I got it back on correctly after taking a break. All is great with the little washing machine once again! Thank you for the installation video and amazingly fast shipping, wow.

door slammed shut

  • Customer: May from Abilene KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
door not level son slammed shut and door strike broke

Loud humming noise from the door closure area.

  • Customer: Alyre from Van Buren ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
First,turned the power and water off. I disassembled the door lock and switch assembly by removing two screws from the rear of the top lid to gain access to the switch. Removed two screws from the switch assembly located in the front door latch area. With screws removed, I seperated the three terminal blocks and inspected the assembly for failure potential. Discovered a small crack in the switch housing which created error in relay function. Ordered the part and installed in reverse order of above. Realigned the door for proper closing, turned water and power on and did laundry all night to catch up!!!

Broken shock

  • Customer: Ron from Blaine WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
As others have mentioned, it was pretty straight forward although a bit finicky to get into the tight spots to press out the pins. The little piece of 1x4 block helped press the pins back in. For the right side shock, I had to undo the large rubber hose at the bottom of the drum and also had to remove the sheet metal shield in the back to allow clearance for the pin to come out. There's only 2 screws holding it in so again, not too hard to do.

Washer would not complete the spin cycle

  • Customer: Andrew from Fruitland ID
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.

belt was still on washer, had developed a loose tear

  • Customer: jeffrey from mount juliet TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Very easy to replace belt on this model, belt had spilt and the loose rubber was flopping around and dislodged plug from water pump. Washer would not start cycle, display showed (no spin). Removed back access panel with screwdriver. Spin the pulley and slip belt off pulleys. New belt is very tight but it will go on, no tension adjustment on this model. Thanks part select quick service will order again from this company.

broken shock

  • Customer: John from Glennallen AK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
removed front panel and used deep socket to remove pins that hold shocks. front left shock took most of the time because of hoses and a unit in the back that needed to be released to be able to remove the pin on the bottom. the right shock was a piece of cake to replace. used a hammer to pull the pins into place (i did not use it to tap on them ) . lots of bloddy fingers from sharp edges.

Washer was "clunking" when in use

  • Customer: Mike from Central Square NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
I replaced both shocks, as both shocks were broken! Keep in mind that Parts select packages them in pairs. I order 2 packages or 4 shocks, guess I have another pair for ~ 5 years from now. These are located under the front bottom panel, so no need to isolate water lines or even pull this sucker away from the wall. Tight clearances are the only factor from making this really easy. Use some Vaseline to assist inserting the new plastic pins.

Noisey shock absorber

  • Customer: Ed from Clackamas OR
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
The parts came with instructions They stated to remove the front panel. This only gets to one side for a difficult repair. I removed the back panel then it was a snap. Easiest with two people.

shocks broke away from washer drum

  • Customer: Rita from Cambridge NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 1 of 1 people found this instruction helpful
replaced the two shocks with the new ones by removing the pins that held the old ones in place.

dryer would not spin

  • Customer: Robb from North Huntingdon PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 1 of 1 people found this instruction helpful
Removed old shock abs. (both sides). The one side, I had to remove the speed control board to access the lower nut on the one shock. Install was fairly easy however, it did not fix the washer. Apparently there was something else (either a switch, the control board or the motor) needs replaced too.
All Instructions for the LTF6000ES1
61-75 of 208