Models > LTF6000ES1 > Instructions

LTF6000ES1 Frigidaire Washer - Instructions

All installation instructions for LTF6000ES1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LTF6000ES1
196-210 of 224
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken doorlatch

  • Customer: ricardo from nesa AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Remove the top cover and the doorlacth and unplug the old parts as simple as that

Valve body froze and broke

  • Customer: Jeffrey from Carson City NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The washer was in the garage, and if you take off the top of the washer, the entire inside is un-insulated. THAT is why these things freeze and break in the cold. Turn off the water, un-hook the water hoses, remove the frozen valve body (two screws into the soap dispenser) and replace. The new part doesn't come with the rubber grommets that slide into the soap dispenser, so use your old ones. Put some WD-40 on the rubber grommets and push the valve body into the soap dispenser....it will slide in soooo much easier than without it. After screwing in the two screws to the soap dispenser, wrap the valve body loosely (but completely) with some fiberglass insulation. I insulated the whole inside of the washer (staying clear of the motor and belt) so that it would survive colder temps!

broken shock absorbers

  • Customer: frank from webster NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
took off front an back panels-pushed half inch socket over pins and pulled them out with channel locks from opposite side of socket-need a piece of broom handle or something about 2 ft. long to tap pins back in to make installation easier

Unit did not drain

  • Customer: chris from burleson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed and replaced pump

Tip of piece broke off in lock

  • Customer: Tamara from Elgin SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
It went easy

A part of the door lock assembly was broken, causing the washing machine not to start.

  • Customer: Laura from Opelika AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The entire process, from diagnosing the problem, ordering the part, and instalation was fantastic! I ordered the part Friday afternoon and had it at my door Saturday afternoon. I was so relieved to read the installation posts from other customers demonstrating how common this issue is and how easy it was to fix! I simply watched the installation video that was sent with my confirmation email. It is also conveniently located on your website. I had the new part installed in less than 30 minutes AND before my husband got home! Thank you Partselect.com!

Drum filling up with water

  • Customer: Jake from St. Martinville LA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug washer from wall outlet. Turn off Hot and Cold water at the valves. Place towel below water inlet on washer and remove Hot and Cold water lines. Use channel lock pliers if connections are too tight. Put hose ends in bucket to catch water left in the lines. Remove two Phillips head screws from the rear of washer cover. Slide cover to the rear to remove. Disconnect 4 electrical harness plugs from inlet dispenser valve. 3 valve plugs, red, green, and blue. 1 thermistor sensor plug. Use Flat head screw driver to pry tabs on inlet valve and vent pipe retainer at the rear of washer. Remove retainer. Twist vent pipe counter clockwise and remove. Use Phillips head screw driver to remove 2 screws on the lower right and left sides of the dispenser valve. Recommend using a magnetic screw driver as dropping a screw will prolong the job. Pull back on dispenser valve and save 2 rubber seals that come out. Put the seals on the new dispenser valve and reverse previous steps to re-assemble.

Washer rocking too much

  • Customer: Greg from Mountain Home AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After watching the video, it was easy to chage them out. Very satisfied with getting order quickly and helpful instructions. Pins came out just like the video, new ones went in with no problem. Washer acting normal again.

Washer Would not drain

  • Customer: Benjamin from New York NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Firs things first - get as much water out of the basin as possible using a siphon or a container and a sponge. Have towels ready for inevitable spillage. Dispose of water in a toilet. Remove the front panel of the washer. The pump is attached with 2 screws/nuts. Remove the pump and place in an empty bucket. Then remove the hose clamps from the washer inside the bucket to catch any water left in the hoses. Attach the new pump to the washer. Then attach the hoses to the new pump. Replacement is very fast and easy - total time from setup to testing, to cleanup 1.5 hours.

Both of the shock absorbers had broken off

  • Customer: Hugh Diggins from Pittsford VT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
In the video sent it showed how to replace the shocks with only removing the lower front panel. I found it was easier to also remove the back panel. There are more screws but it provided open access to the pins that needed to be removed. The parts went in easily and when compared to the original equipment looked stronger.

Excess noise in pump, forigien drill bit hitting inpeller blades

  • Customer: Joseph from Magnolia MS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Very simple, unplug washer for safety, remove 2 Phillips screws form bottom of front panel, slide panel down to slip the ears out of their slots. set panel off to side, remove the electrical plug on the pump, unscrew the two hold down Phillips screws, raise the pump up and slid a heavy absorbent towel under the pump, loosen the two clamps, slide the hoses off, remove the sloppy wet towel, install the new pump, and screw it down, push the electrical connection on, slip the hoses on , clamp them in place, install the front cover by aligning the slot and ears up, use a screw driver or something the raise the panel up in place then install the last 2 screws plug it in your done.

The top striker tip broke off....

  • Customer: teresa from brooklyn NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the broken striker, screwed in the new one in less than 2 minutes...this is the second time it was replaced...the first time I was still under warranty...he took about the same amount of time to install ...I ordered 2, because I know it will be broken again....

Washer would not go in high spin

  • Customer: Randall from Doe Run MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
It is a front load washer with a dryer stacked on top of it.Insaw a video on u tube. I took a neddle nose pliers ang took a spring loaded metal ring off that is holding the grey rubber boot on . I peeled it back just enough to reach ih and get the door lock in hand.I then took a phillip screw driver and removed the two screws un the front off holding the door lock..I then reversed instructions,and put the new lock in.The complete job took lease than 5 minutes,and the part did the trick. My washer works as good as new.

Washer would not start after I opened and closed the door.

  • Customer: Sue from Simpsonville SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the door lock and switch assembly. With needle nose pliers, I removed the metal ring around the washer gasket. Removed two screws on assembly and removed the entire assembly. Noted part number and ordered part which came in 3 days. Reversed the above instuctions for removing the assembly. Was washing within the hour. By the way, I am a 65 year old woman.

Brokken Hindges and door Strike

  • Customer: Robert from Diagonal IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove Door and front panel, breakdown door and remove front panel. Reassemble door using new front panel and install door strike and bottom screw on door. align hinge with tabs on hinge assembly and insert tabs on front panel and squeeze door parts together and install rest of screws. Job complete
All Instructions for the LTF6000ES1
196-210 of 224