Models > LTF2112ARW > Instructions

LTF2112ARW Admiral Refrigerator - Instructions

All installation instructions for LTF2112ARW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LTF2112ARW
316-330 of 430
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the 2 yr old icemaker tray had deterioted and the ice stuck

  • Customer: Richard from Mt Airy MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I had to replace the whole unit. The tray should have lasted longer and there should have been a replacement tray available.The installation was easy. 3 screws removed, unplug unit, turn off water and put in new unit.

No ice. Web site explained what to check for ..

  • Customer: Stewart from Ventura CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Just followed directions.Which were clear as could be. I think it took longer to clear the freezer, than to replace the ice maker. Thanks so much.

Fan came off motor shaft and busted a blade off.

  • Customer: Daniel from Hubertus WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Open access cover on the fan compartment. Fish out broken fan. Push on new fan blade onto motor shaft and re-install access cover... Job over! It was awesome to be able to find parts and not have to pay a repairman for such a basic fix.

Replaced ice maker

  • Customer: Christopher from Cave Creek AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged refrigerator and truned off water supply. I then removed old ice maker by first removing screw holding mounting bracket with 1/4 inch nut driver. Then I carefully pulled up and out on the ice maker to remove it from mounting brackets on the side of unit. Once free, I was able to access the wiring harness in the back and remove it from the unit by compressing the clips and gently pulling with an even pressure. Now that the old ice maker was detached I took it to my counter and removed the on/off switch rocker bar and wiring harness. I attached these two pieces to the new ice maker. I then plugged the wiring harness back into unit and lined up the mounting brackets on the side wall and did a reverse tilt to downward pressure onto brackets until they clicked in securely. The last step was to screw in the mounting bracket with nut driver. Turned on water line and plugged machine back in. It took about an hour and a half before it produced its first harvest of ice, but has been working like a charm since.

Ice leaking water.

  • Customer: Paul from Madison WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watch the video on the sight and that was almost all I really needed. The only thing I would add is that it took me some time to get the drawer freezer door off. Lift the front straight up. Don't pull the door slides out.

Ice Maker worked sporadically and then started dropping water into bin, make a large chunk.

  • Customer: Harold from Spring Branch TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Was very happy with the experience of using your company. The man on the phone was helpful. The icemaker shipping was only about $7 and got here in a couple of days. I liked the video, and then including a link to the video with the on-line confirmation. Was not quite sure it was the icemaker or the metering valve on the back, as the latter would make a little grinding noise, but the symptoms matched the dumping of water into the bin. After replacing, everything is working well. The only difficulty was the wire harness plugs into the other side of the back of the box than in the video and I found it a little difficult to route the wires correctly as they seemed too short. But a little trial and error solved that. My model is freezer on the bottom and I didn't notice that the little detachable funnel wasn't quite seated and it was necessary to reinstall, making sure the funnel stayed in place correctly. That was my own error. My overall experience was excellent and I would not hesitate to recommend PartSelect to anyone with an icemaker problem. I'm only sorry I lived with a recalcitrant ice maker for a couple of years before finally acting on it. I am glad I found your website! Lee in Texas

Not making ice, leaking water.

  • Customer: Robert from Youngstown OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed icemaking mechanism replaced with new. Works better than ever

Ice Maker would not make ice

  • Customer: Philip from Hoschton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Quick repair especially with YouTube video; took less that 15 mins including moving ribbon cable & fill wire. Saved at least $200.

Ice cresents froze together in one big lump

  • Customer: Lloyd from Stilwell KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Simple replacement of the icemaker solved the problem. I suspect the icemaker was overfilling resulting in water flowing into the ice reservoir.

Ice Maker not making ice

  • Customer: Ellen from Vienna VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
This was about 10 time easier than I had expected (I'm in my 30s, a mom). I put this off for almost a year groaning that I would have to spend tons of money on a repair man. It was really no big deal and took under 30 minutes. I used the video from PartsSelect, and it was right on. I was initially worried because the description from the website said that the new ice maker didn't come with the 'harness" and I had no idea what that was. Its just the little set of wires that easy unclips from the old unit and pops right into the new unit. Mine was reusable, so pretty easy. The only minor issue I had was that the new bracket didn't line up comepletely with the hole in the fridge where the screw went in, but I solved that with adding a skinny washer. Would definetly recommend any common-sensed person to do this repair yourself.

Ice maker was leaking

  • Customer: William from Noblesville IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I couldn't believe how easy it was since I am not the handiest guy. All it look was to switch over the wires and screw it to the inside of the freezer. I was back in business.

Icemaker had been sluggish for a while. We had to keep the wire (bale) in the off position for half hour or so, then put it back in the down position. After a few months of doing this, it stopped making ice altogether.

  • Customer: Elisabeth N from Katy TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Shut off water and unplug fridge. Remove ice drawer. Unscrew one short nut underneath icemaker, and the two longer ones holding it to the wall of the freezer. Now remove white cover. It just needed a little jiggling w a flat head screwdriver to loosen it. Now you can see where the wire harness is connected, use the same flathead to depress the plastic pin holding it in place, and slide it out. Remove the wire harness from the metal clip on side of icemaker. Now you should be holding the old icemaker in your hands. Remove the bale carefully. Now install the bale into the new icemaker, while making sure it's in the 'down' or 'on' position. Bring the new icemaker into position, gently snap the wire harness into place, sliding the wire into the clip like it originally was. Fasten the three screws again. Then, finally, snap the white cover back into place. Slide the ice drawer back into position, turn on the water, plug the fridge back in and wait 30-45 minutes for your first batch of new ice cubes.

The ice in the ice maker would freeze into a solid block. Upon inspection I realized the ice maker was leaking water into the ice holder which was then freezing solid. Three tray for the ice maker was slightly rusted and caused the water to drip.

  • Customer: sal from lighthouse point FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the video on how to change the ice maker, very easily explained, and removed the old in about 10 minutes.After seeing how the old one came out it only took five minutes to install the new one. The appliance repaircompany wanted$120 just to diagnose the problem,i bought the part from partselect for$104 total. This is the forth time I've used this site and saved a ton of money.

ICE MAKER--NO ICE

  • Customer: ALTON from POQUOSON VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
DISCONNECTED POWER--REMOVED ICE HOLDER TRAY--REMOVED ICE MAKER END CAP--DISCONNECTED ELECTRICAL WIRES--REMOVED ONE SCREW HOLDING ICE MAKER TO REFRIGERATOR--LIFTED UP ON ICE MAKER TO REMOVE IT FROM TWO HOLDERS--TOOK CONTROL WIRE FROM OLD ICEMAKER AND INSTALLED IT ON NEW ONE--REINSTALLED NEW ICEMAKER IN REVERSE ORDER.

Icemaker making a clicking noise not dumping ice.

  • Customer: RICHARD from COLORADO SPRINGS CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Rmoval and replacement is not at all complicated. (1)Reach behind and to the left of the icemaker and release the power plug. There is a release snap on th side of the plug. (2)Using a 1/4" nut driver remove the screw holding the icemaker to the "L" bracket at the bottom of the icemaker. (3)Using the nut driver loosen two self taping screws holding the top of the icemaker to the side of the freezer compartment.(4)Lift up on the icemaker to remove it. (5)remove the white plastic cover from the front of the icemaker (pry out at the bottom) and snap it onto the new icemaker. (6)Remove the wire sensor arm from the old icemaker and place it on the new one. (7) Remove the cable assembly (plug) from the old icemaker and fasten it to the new one. (8)Secure the new icemaker in place using the reverse order as the removal. The icemaker will take a little longer to make its first batch of ice as it will have to attain its proper operating temp (0 degrees to 2 degrees F).
All Instructions for the LTF2112ARW
316-330 of 430