Models > LTF2112ARW > Instructions

LTF2112ARW Admiral Refrigerator - Instructions

All installation instructions for LTF2112ARW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LTF2112ARW
271-285 of 430
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water over flow.

  • Customer: Dennis from Cincinnati OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 3 people found this instruction helpful
First I unplugged wiring harness from the inside of the freezer. Then removed two small bolts on top side and one on the bottom. Then took it out of the freezer. Then unplugged the wiring harness from the ice maker. Then plugged it into the new ice maker. Then reinstalled it back into the freezer with the three bolts.Then plugged it back in.

Black deposits in ice - Ice maker does not stop on its own

  • Customer: Roger from New Bedford MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 4 people found this instruction helpful
Replaced ice maker assembly, 5 screws out, unplug the wire, take some attachments off the old ice maker and put it on the new one, plug it in, 5 screws in...done. I did have to take a mirror to see how to unclip the wire, which turned out to be the hardest part of the whole job..

ice maker not working-components iced up and frozen over

  • Customer: David L from Scottsdale AZ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 4 people found this instruction helpful
It was easy and my daughter did most of the work while I assisted.
Removed contents from freezer, unplugged refrigerator, shut off water to ice maker. Used hairdryer to thaw inside, placed ice catcher in sink to thaw. Removed defective ice maker and transferred trip lever and wire bundle to new unit. Installed new unit, bent mounting bracket located on bottom of new unit so that when installed the ice maker is horozontally level. Plugged refrig in and turned on water. Water does not come in right away as the temp probably has to be restored to freezing level before things start to work....so just let it run. In the morning lots of nice cubes and no leaks...hooray!

Ice maker ejector arm broke into.

  • Customer: Mary L. from Millsboro, DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 26 people found this instruction helpful
Removed old ejector arm and installed new part.

Leaked water as filling

  • Customer: Walter from Torrance CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 43 of 1234 people found this instruction helpful
Removed mounting screws
Disconnected file hose
Flipped unit over to remove connecter
(This was the only difficult operation; unpluging & pluging it in)
New part fit was very good
Reversed the disassembly order to install
New assembly had to cycle a while to produce ice cubes. I'm very happy now, so bring on the hot weather.

Ice maker stopped working. Turned out a connection on the heating bar shorted out.

  • Customer: Russ from Supply NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pulled the plug on the refrig. ( This is important since the heating bar on the bottom of the ice maker could come on as soon as you plug it in and burn your hand ). Removed the ice bin to get it out of the way and then removed the 1/4" hex screw from the support bracket under the old ice maker ( don't lose it ). Pushed up on the old ice maker to dislodge it from the 2 support clips on the top of the ice maker. Squeezed both sides of the wire harness plug and pulled it out and removed the old ice maker. Removed the wire harness and level bar from the old ice maker and installed them on the new ice maker. Plugged the ice maker wire harness into the female receptacle in the freezer. Popped the ice maker in to the top support clips making sure the rubber water chute from the refrig. was in place in the round ice maker receptacle. Plugged bak in the refrig. and I was getting ice in about 2 hours. Working fine after 1 week producing plenty of ice. RussK---

ice maker stopped making ice

  • Customer: David from Jacksonville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
following the advice of this site, purchased a new ice maker. Old one was simple to unhook and remove and new one was just as easy to install. Within no time at all, I had ice being made and it has been working perfect since. Thank you for the help...

Ice Maker was not functioning

  • Customer: BRET from SAN DIEGO CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed your posted video. Did step by step as video instructed and in about 30 minutes finished. Ice was made approx 30 minutes later. I hope you do more videos, a picture is worth a thousand words.

Would not defrost & Refrigerator would not get cold

  • Customer: Robert T from Fresno CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the defrost heater and everything is working now! Thank You for the discount parts and information Fresno Ca.

Leaking water

  • Customer: Terry L. from Glasgow KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed Ice bin, remove rails on left side that hold ice bin. Remove one screw holding ice maker to refrigerator wall,then lift ice maker off holding screws. Unplug wire harness from back of refrigerator. Remove wire harness and loading wire from old ice maker and install on new unit. Re-install new ice maker by reversing steps. Videos where very helpful.

Ice maker not working

  • Customer: Charles from Middletown OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed on line instructions. Instructions were very helpful. The part was an exact replacement. Everything went as planned.

Was Not Making Ice

  • Customer: Don from Desert Hot Springs CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the Video, and it went almost as the video, except for the rails for the ice tub, so instead of the nut driver, had to use an open end 1/4" wrench. Now its a working with lots a ice....

ICEMAKER

  • Customer: BETTY from HOCKLEY TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I RECEIVED THE NEW ICEMAKER THE NEXT DAY AFTER I HAD ORDERED IT.AFTER WATCHING THE VIDEO ON HOW TO INSTALL THE ICEMAKER I INSTALLED IT WITHIN A FEW MINUTES WHICH I REALLY SURPRISED MYSELF SINCE THIS WAS MY FIRST REPAIR JOB TO DO BY MYSELF.THE NEW ICE MAKER HAS BEEN WORKING GREAT AND I AM VERY PLEASED WITH PARTSELECT AND WILL CONTINUE TO CONTACT YOU WHEN I AM IN NEED OF ANY PARTS. THANK YOU, BETTY

dripping and making globs of ice

  • Customer: Edward from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1 removed ice basket 2 remove cover over basket 3 unplug power cord 4 loosen top screws with 1/4 in nut driver (do not remove the completely) 5 remove lower mounting screw ( not necessary to remove basket rail) 6 remove ice maker from unit 7 remove bale from old unit 8 install bale on new unit 9 remove front cover from old unit 10 remove power cord from old unit 11 plug in cord to new unit 12 install old front cover on new unit 13 mount unit in freezer 14 hang unit on top screws 15 install bottom screw 16 plug in unit 17 put in ice basket and cover. no runs, no drips, no errors. Ice was made in about 2 hours.

Ice Maker stops working..

  • Customer: Tony from Litchfield Park AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Fast delivery...Great video instructions..The only difficulty is when I tried to take the cable out. It's kind of hard and far away from my reach. So, I took only the cable out on Ice Maker end.
All Instructions for the LTF2112ARW
271-285 of 430