Models > LTF2112ARB > Instructions

LTF2112ARB Admiral Refrigerator - Instructions

All installation instructions for LTF2112ARB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LTF2112ARB
376-390 of 407
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

While closing the door, I somehow cracked off the light switch button.

  • Customer: Bruce from Duluth GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Popped out the old one......plugged in the new one and popped it back into place. My wife was happy in have light again in the fridge!

no ice ,dead ice maker

  • Customer: brett from chicago IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
turned off freezer unplugged ice maker ,unscrewed 3 screws, removed ice maker,wiring harness and wire that goes up and down to control ice maker. installed all in reverse put back in and turned on waited and waited no ice ,theres a little control valve that let's the water in as well that was shot as well had to go get one at a local shop fairly interchangable just pull the other out and take with you,or just order one with your ice maker if you have the fridge out you might as well change it as it's just as old as the ice maker as well .everything pumping well,like never before, tons of ice all the time also put in filter on the water line as well really good tasteing ice now.

broken spring in the light switch in refer

  • Customer: Peter from Avila Beach CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Initially thought I could repair switch, but then discovered spring was broken. Ordered the new switch (Parts Select is very efficient - received switch in 3 days). Was encouraged by the posts regarding the switch installation. I had some difficulty removing the old switch. Used a pocket knife to ease the switch out of the hole to reveal the clip/spring. After noting the clip/spring location I used a small flat-blade screwdriver to release the clip. Even though I released the "molded" clip/spring(be sure to note where the spring is on the new switch and release it on the switch it was tight in the hole and had to use pliers to carefully remove the old switch. After removing the old switch, used pliers to gently remove the wire leads. Then install the leads on the new switch. Note the orientation for replacing the switch and gently feed the connecting wires into the hole so they won't kink or prevent the switch from entering the hole. Install the switch noting the clip/spring location and the orientation of the lever that the door closes on to turn off the light. Be sure to put it in without binding at an angle. Thanks to Parts Select for this service! I'll definitely be back.

Replace Ice Maker

  • Customer: Terri from Manhattan Beach CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The fix was relatively easy but I could not get 2 of the screws removed. They were in very tight and I didn't have the right tools. Also, in the Amana refridgerator, they are in a "difficult to get at" location. I called my plumber friend and he helped me. Once the screws were out, the rest of the job went very smoothly as others have described. We took out the bad icemaker and reconnected the new one to the existing harness. I had ice in an about an hour. Thanks so much, PartSelect. The delivery was quick and the install was as many described on your website. You provide a wonderful service for the "do it yourselfer". Terri

Noise coming from freezer section

  • Customer: Jim from East Canton OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took freezer rack out of freezer,took 4 screws out of back freezer panel, removed ice maker plug from panel and pulled panel out only needed to get panel to come out so far pushed on clips to remove fan cover it's easier to get behind cover to push on these clips then it is to do it from the front of cover and these clips are plastic so they can brake easy when they are cold.I put freezer panel back in place the old fan blade came off fan motor shaft I took old fan blade out and installed new fan and put new fan blade on pushing it on till it stops on fan motor shaft, I put new fan blade clamp on used a flat tip screw driver to help a little bit reinstalled fan cover making sure clips on cover snap back in place put freezer rack back in and everything works great took about 15 to 20 minutes to do.

The ice tub corroded so the ice would stick.

  • Customer: Hal from Marathon FL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Couldn't believe how complicated this part is with heaters. It is used in at least a billion refrigerators and functions well. But I had to tear it all apart to adopt it. Got it all done and stayed awake all night for waiting for Ice. Nothing! Then a Erika moment! Turn the ice arm full switch off! Then Ice poured out every hour. Expecting many years of ice. Thanks for speedy delivery especially before Christmas..

new prob. ice dispencer door seal leaks

  • Customer: vern from lake placid FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
need instr. to repair

Ice maker was dripping water in two different area's

  • Customer: Michael from Maplewood MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The repair was a lot easier than I thought. I first ordered the ice-maker part from PartSelect. Followed the instructions from the how-to video and I was done within 30 minutes. Unplugged the fridge, took out the two 1/4" nut screws holding up the ice-maker, disconnected the wiring harness and then re-attached the new ice-maker in reverse order. Had to use some of the parts from the old ice-maker, like the cover, ice wire (the wire that moves up and down, letting you know when the ice box was full or starts the ice-making process) The whole process along the PartSelect video made it easy.

follow the video that PartSelect has online

  • Customer: Rich from Wickenburg AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watch the video and then do the repair.

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Ice maker not making ice

  • Customer: JOHN from SAINT PETERS MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First of all, I do not consider myself very handy. Most of my simple home repair projects include at least 2 trips to the local hardware store and take twice as long as they probably should. So if I can do this anyone can. For once, rather than just blindly throw new parts at a problem I did check the water pressure to the icemaker first and then even tested the icemaker with a multi-tester to determine what was wrong. I had $5.00 mulit-tester in my workbench but had never actually used it before, so I found step by step instructions on another website on how to test the motor and it turned out that one of the circuits in the main motor was in fact bad. Since the motor was around $80.00 dollars and the Whole unit that's inside your freezer is about $120.00 I decided it was best to just go ahead and replace the entire unit rather than just the motor. From what I saw online normally replacing an Ice maker is fairly simple. Remove 3 screws swap the prewired plug along with the metal arm then just reinstall it. Somehow whenever I try a home repair it's never that simple. First of all, our freezer is on the bottom so removing the screws holding the ice maker meant that I had to climb over, around and under the freezer shelves in order to get to the ice maker itself. Also one of the screws is not visible from the front so I had to hold a mirror in one hand while I tried loosening the screw with the other. Since the metal arm that turns off the ice maker is not included in the replacement it had to be moved over. Of course it was stuck, so it did take a little time to get it loose because I was being careful not to bend it and have to order another one. Finally installing the new icemaker meant once again that i was climbing over under and around the basket in the bottom level freezer. There is probably an easy way to remove the entire drawer but I couldn't find the release tabs so when just pulling harder on the drawer didn't work, I thought it best to just work around it. Still all in all, not a difficult job, just a little time consuming. The guy in the video did the swap in about 6 minutes, it took me about 45.

The ice maker was leaking into the holding container and had black chips of paint or plastic from the inside of the icemaker

  • Customer: Gerald from Waukesha WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Installation was really easy since the replacement part was identical to the OEM part. Removed the three mounting screws with a nut driver. This allows one to remove the icemaker from the wall and disconnect the wire harness plug from the icemaker. I never unplugged the harness from the rear wall of the refrigerator. Put the new icemaker in place, making sure to place the water fill tube in the proper hole. Plugged the wire harness into the new icemaker and tightened the three mounting screws. The icemaker worked perfectly from then on with clean ice cubes and no leaks.

PART WHERE ICE MAKER ARM FIT IN BROKE OFF

  • Customer: Yvonne from Worthington IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK ICE MAKER OUT ALL TOGETHER WE REMOVED 4 TO 5 SCREWS HAD TO REMOVE AXEL TO GET THE BROKEN PIECE OUT AND NEW ONE IN MY HUSBAND SAID IT WAS EASY IN AND OUT IN ABOUT 15 MINUTES SAVED ABOUT 150.00 THANKS PARTSLECT

Icemaker leaking water and creating ice jams in freezer

  • Customer: David from Houston TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced icemaker by using total kit. Watched youtube video put on by partselect folks. Very easy to follow.

Ice maker leaking water dripping into the bin and freezing the dispensing unit

  • Customer: Richard from Port Orange FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I checked the part number and an exact replacement was ordered. The old unit was removed and what I failed to note was that the water supply hose for the new unit entered from the side. Further examination showed a small "break-out" piece at the rear of the unit. but I still had to do something about the hole in the side. I used a piece of metal tape to close off that hole, trimmed it to size, and installed the unit. It was really an easy install after I figured out what to do about the hole. Evidently, this unit is mounted on the side of the freezer compartment in some models. Reading the reports of others was a big help.
All Instructions for the LTF2112ARB
376-390 of 407